What does it mean to install 3dmax9 0 when you install something in English? What to do? 5

The English meaning is:

The installer detected that the following programs are running.

In order to complete the installation, these programs must be closed.

Select OK to proceed with the installation.

Select Cancel to pause the installation.

You just shut down the process!

The way to abort the process is to open the task manager (start menu Run can be entered and press enter), then click on the "Process" property page, find the process, select it and click the "End Process" button, OK. Once the process is aborted, it can be continued.

Judging from the information on the Internet, there are often some problems with the installation and uninstallation of 3DMAX, so I can only wish you good luck!

This program is running, click OK to install it, and click cancel to stop.

You close the software and install it.

Open the task manager and take a look, it should be running, it may be a background operation.

The device detects that these programs are running, and in order to complete the installation, you must close them, select OK to continue the installation, and select cancel to stop the installation.

After 3DMAX is installed, the default English interface is in English, how to change the English interface to the Chinese interface?

Here's how: <>

Figure 1<>

Figure 2<>

Figure 3<>

Figure 4 Step 4: Select the shortcut "3dmax-simplified Chinese" file, right-click "Properties", select the address of the "Target" column in the "Shortcut Bar", and press CTRL+C to copy; See Figure 5

Figure 5 Step 5: Go back to the desktop, select the shortcut "3ds Max" file, right-click "Properties", select the address of the "Target" column in the "Shortcut Bar", press Ctrl+V to paste, click "Apply" and "OK" in the lower right corner to close the window. See Figure 6

Figure 6 If it helps, please like it, thank you!

Figure 7

There are some differences between 3ds Max 9 and previous versions in terms of installation, and here we will introduce readers to the detailed installation process of 3ds Max 9, as well as some things to pay attention to when installing.

2) Click the [Next] button, select the [I accept the license agreement] radio button in the next interface, and click the [Next] button, and fill in the user information in the next interface, as shown in the figure.

3) Click the [Next] button to enter the custom installation interface of the program, as shown in the figure. In this interface, the reader can customize the installation location of the program by clicking the Browse button.

4) Select the Autodesk 3ds Max 9 option in the above interface, click the [Next] button, and the installation wizard will continue to guide the reader through the installation settings. Be sure to select this option in this step, otherwise the installation will fail. This is one of the direct reasons why a lot of readers get errors during the installation process.

6) Click the [Next] button, the wizard will list the information filled in the above steps, if you confirm that it is correct, click the [Next] button to start the installation operation, as shown in the Huihui diagram.

7) After the installation is completed, click the [Finish] button to complete the installation of the whole program.

Unlike previous releases, a welcome screen has been added in 3ds Max 9. The interface shows some of the most common modules in 3ds Max, such as creating objects. Readers can follow the corresponding tutorial by clicking on the corresponding button.

The following image shows the tutorial interface for transforming an object.

Double-click directly to run the installation package, run the software after installation, and you will be prompted to enter the registration code, and use the keygen to calculate the input.

Here's how:1Open the VR panel of the VR system as shown in the figure, adjust the "maximum depth" to 60 (this is the occupation of computer resources per unit time, and lowering it will slow down, but it is safer, and it is only used in this case);

Set the "dynamic limit memory" to between 1200 and 1400 (for example, 1400m is the limit memory of VR, and it will jump out if it exceeds 1400).

Set the Default Geometry to Dynamic

Through the above three steps, the limit memory of VR was adjusted to 70% of the limit memory of 3D, which is in the "low-speed safe rendering range" (I just acquired this term).

Finally, check Low thread rendering priority.

Test if it is feasible with a success rate of 60

Continue above. 2 Open the VR panel Secondary** VR light cache (if you are using another engine, also according to the following rule), reduce the parameter value related to the fineness of the light by half, such as 1000 to 500 below and do not change the other (this will cause a sharp drop in photon quality, of course, the speed and memory footprint will be optimized).

After rendering once, check Save to light.

Using the previous step may cause light leakage or dark spots, turn on the VR Light Map column Set the hemisphere subdivision and differential sampling to 150,100 (increasing the hemisphere subdivision will slow down the speed and increase the memory, the same is true for differential sampling, but it can effectively eliminate light leakage and dark spots) (this step is contrary to the original question, and is considered an additional reminder).

Test if it is feasible with a success rate of 75

3.Modify the panel of the model with a large number of faces in the model (take an appropriate amount of value to ensure that the model does not change greatly, which can greatly reduce the number of faces of the model and save computer resources.)

Or through the model out of the specific operation method is very simple and will not be repeated.

Turn on 3DMAX

Test for success with a success rate of 90

There is a fatal weakness in the default parameters, resulting in a large number of models that cannot be rendered, and 3dmax9 itself has "cerebral thrombosis" You can create a panel tool last reactor collision Storage collision If a number is displayed in it, please select Clear, and check Do not save for file** ** After saving the file, you will find that the file size will usually be reduced by 3-10 times.

Test if it is feasible with a success rate of 100

Please refer to the above 5 steps in detail. Bonus points Good luck.

I've had this kind of problem, which is to hide some things in the scene, and use less points and more models, and it's good.

Pretending to be 64-bit is no problem.

This kind of error is more common in China, and the solutions are:

Mine used to have this kind of problem, but changing to a higher version solved it. It may be caused by a higher version of the framework program Microsoft Visual C++ required by the MAX software, so changing to the corresponding higher version will solve the problem.

Personal opinion, hope it helps you -