-
The router and wifi are not easy to use, and the settings are generally wrong
If you didn't enter the password incorrectly, just set it up again, and the steps are:
1.Turn on the power supply, and then plug in the network cable, plug the line into the WAN port (usually the blue port), and then connect with the computer network cable just plug in which LAN port, after doing these jobs, then you will see that there is an address and account password behind the router, after connecting, enter the address you see in the router in the browser, generally of course, if you are using ** online Internet access at home, then you have to prepare an additional modem, commonly known as "cat").
2.Then enter, enter the corresponding account and password, generally the new ones are admin
3.After entering the operation screen, you will see a setup wizard on the left, Attack on the entry (usually it pops up automatically).
4.Click Next, enter the Internet access method settings, we can see that there are three Internet access options, if your home is dial-up, then use PPPOE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer.
The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP. I chose PPPoE because I dialed.
5.If you choose PPPOE dial-up Internet access, you need to fill in the Internet account and password, which should be understood by everyone, and there will be an account number to open broadband, and it is OK to fill it in!!
6.Then the next step is to enter the wireless settings, we can see the channel, mode, security options, SSID, etc., generally SSID is a name, you can fill in as you like, and then the mode mostly uses 11BGNFor wireless security options, we need to choose WPA-PSK WPA2-PSK, which is so safe that it will not be hacked and rubbed by the network.
-
What do you mean, can't you do it?
-
Computer network Lianjia Zheng sedan car connection shows unknown solution:
Tools Ingredients: Computer, computer manager.
1. First turn on the computer, then enter the computer desktop, then double-click to open the "Computer Manager", and then click "Toolbox".
2. Then click on "Computer Diagnosis".
<>4. Then click "Disk icon shows unknown icon L", and then click "Fix Now".
5. Then it should be noted that to fix this item, you need to temporarily close the "Explorer".
6. Finally, wait for the repair to be completed.
-
The computer cannot access the Internet and the network connection is displayed as unknown, which is caused by an error in the broadband configuration of the Rubber Sun machine in the calculation, and the specific repair methods are as follows:
1. First, find the icon of the computer on the desktop of the computer, and then right-click and select Device Manager
2. Then find the network adapter in it, that is, the optical modem of the computer, and update its drivers
3. Then go back to the desktop, find the icon of network connection in the lower right corner of the taskbar, and click Open:
4. Then in the local connection status window that appears, click the properties button at the bottom left:
-
Cause: The network icon is turned off in the system icon in the notification bar. The following uses the win7 system to demonstrate the solution process:
1. Turn on the computer, right-click on the blank space of the taskbar, right-click on the dish-car-click properties.
Second, then enter the taskbar interface and click the custom button in the notification area.
3. Find the link to open or close the system icon and click to enter.
Fourth, finally set the network display status to open, and destroy it before clicking to hit the Wisdom Hengding button.
5. As shown in the figure below, after setting, the network icon will be displayed in the notification bar.
-
You try to install a driver wizard first, and after installing it, backup the network card driver first, and then restore the driver. If the network card driver is updated, you can choose to update it.
-
Is it a wired network or a wireless network, I said I also shared?
-
Leave it alone, maybe you'll be fine sometime.
Your problem should be caused by the deactivation of some services on your computer, please enable the deactivated services, and then start these services You can click Start, press the right mouse button on my computer, and then click Manage. Double-click Services & Apps, then double-click Services. Press the right mouse button on telephony once and click on the content. >>>More
You look at the back of your route.,There's a **.,Like mine, you can see a login page after entering the password After entering, click on the setup wizard You put your Internet password back in.,That's it
Listen to you, you should use the dial number. You should use the cat directly on the net. No routing, only you are using your network cable? >>>More
In fact, it's very simple, don't be so troublesome, if you change the network environment, directly delete all the connection methods of the network connection, let the wireless network automatically find a new connection, it will definitely find the connection of your wireless route (here does not rule out that your neighbors have wireless routes, if there is a possibility to find several connections), but this premise is that your wireless route must be set up. >>>More
First of all, it feels like you are sharing the Internet in a local area network, and we will analyze it with the elimination method. First of all, you said that the network cable can be plugged into other computers to access the Internet, indicating that the end of the network cable interface is normal, and the conclusion is that 1. Your computer may have software and hardware problems that cause you to not be able to access the Internet. 2. Your computer is restricted by the server or router. >>>More