Subject 2 How to pass a right angle turn, Section 2 right angle turning tips

When turning at a right angle, try to stick to the right sideline as closely as possible, and pass in first gear.

The following are the specific tips for clearing the right angle turn in subject 2:

1. Control the speed of the car: the timing of the direction is the most important, to control the speed of the car, rather slow than fast. 2. Cornering skills:

In the process of turning, pay attention to the left rearview mirror, the distance between the left rear wheel of the car and the corner, if you are about to crush the corner, you should quickly return to the right half a circle, and wait for the wheel to cross the right angle and then kill the direction. 3. Kill the steering wheel: When the left rearview mirror is in the same parallel line as the transverse road, the steering wheel needs to be killed when the handle in the left door is about to coincide with the corner of the road or when the front of the car is pressed against the yellow line in front.

Subject 2: Essentials of right-angle turning.

<> "Branch Blind Quarrel Two Right Angle Turning Tips."

1. Step 1 into the right-angle turning test area, turn on the left turn signal and keep for 3 seconds, the vehicle is close to the solid line on the right side of the road, and you can rely on the front right corner of the hood and the curb line to be attached when chasing the line, the purpose is to keep a distance of about 30cm between the body and the left side line.

2. Step 2: Go straight slowly, and quickly fill the direction to the left when you observe that the edge of the window is aligned with the inward right-angle curve turning point.

3. Observe the left rearview mirror during the turning process of step 3 to ensure that the left rear wheel is not pressed to the corner line.

4. Step 4: When the front of the car is aligned with the exit of the test road, quickly return to the right direction, and at the same time, you can observe the left and right rearview mirrors to ensure that the body is in the center of the roadside line on the left and right sides. Just drive out of the test area.

The right-angle turn is the easiest subject of the five infield and has only two points. The first step is to confirm the point where the vehicle is in the lateral position. When turning left in a narrow area, the vehicle should keep to the right as much as possible, usually leaving only a safe distance of 30 cm from the right-hand side of the road.

Then there is the point where the timing of the steering wheel is operated. This is the point where the vehicle kills the steering wheel to the left when it is in the longitudinal position, and it will press the inner corner if it is early, and the edge line of the front road will be pressed if it is late. First of all, use the wiper protrusion point to align and keep driving on the right side of the road to confirm the accuracy of the vehicle's lateral position.

Align the center point of the front edge of the hood to the right and keep driving on the right-hand sideline.

Secondly, when the lower left corner of the front windshield is "against the edge line" of the front road, the steering wheel should be hit to the left to the end. Or, when your shoulders are close to the inside corner, hit the steering wheel all the way to the left. The speed and direction rhythm of the vehicle should be well controlled during operation, otherwise it will increase the probability of error.

The right-angle turning event is not very difficult, and it requires repeated practice to accumulate experience and increase operational ability. As long as you practice repeatedly, you will pass without a hitch.

The simple right-angle turning trick is as follows:

1.Adjust the position of the right rearview mirror, try to keep it low, and it is best to look sideways at the right rear tire;

2.Try to slow down as much as possible when the car is about to enter a right-angled curve;

3.The fulcrum of the left wiper is glued to the left line of the right-angled bend. This point will vary according to the position and body type of each person, mainly to ensure that the distance from the left tire to the left line of the right-angle bend is 15 20cm, and to ensure that the body is positive;

4.After the front part of the car passes the horizontal line before the right-angle bend, turn your head to observe the position of the extension line in the right-angle bend at the handle of the window door (the position grasped when closing the door), and stop the car;

5.The steering wheel was killed to the right, and the car moved slowly forward, successfully completing a right-angle turn. Note:

It's best to pay attention to the right rearview mirror when turning. When the rearview mirror sees the right rear wheel approaching a right-angle turn, observe whether the right rear wheel will snap the line. If there is, immediately hit the steering wheel back to the right, drive forward, and then kill to the right to complete the right-angle turn.

Specific right-angle turning techniques:

First, the speed is slow before bending, and straightening the body is the key. Before the vehicle makes a right-angle turn, it is necessary to judge the width of the road surface. When the vehicle deviates from the right angle of 5-6m, reduce the speed, hang to a low gear, honk the horn, avoid other vehicles and pedestrians, drive as close to the outside of the road as possible, turn left and right, correct the body, and drive slowly.

The second and second gears are inclined outward at low speed and cannot be pressed. When the body is straightened and the speed is reduced, it is engaged in second gear to make the vehicle run smoothly close to the outer edge of the road and control the lateral spacing. It is advisable to keep a distance of about 10cm between the outer wheel and the outer edge line, and keep moving in parallel.

When approaching the turning point in the front of the car, immediately make a sharp turn. When the current bumper is flush with the protruding point, quickly turn the steering wheel to the left (right) to the limit position. At this time, it is necessary to pay attention to Lu Chun, observe the swing of the body and the trajectory of the wheels, use idle or lightly press the accelerator pedal to move forward, and avoid slamming the accelerator pedal.

There are also driving test mock tests.

3.If you are passing through a right-angled bend of a road about 7m wide, turn right and cross the road centerline. When the front of the car is close to the turning point of the road about 1m, quickly turn the steering wheel to the right to the limit position; When turning left, you should first drive on the right side of the road.

When the front of the car approaches the turning point, it starts to turn the steering wheel and reaches the limit position. Let's see if we can get past the front, and consider moving forward slowly. If you are unsure or unsure of a right-angle bend, you can stop and check it in advance.

During the passage, keep calm and always pay attention to the movement of the body and the position of the wheels. 4.When the front of the car is close to the right-angle turning point, turn the steering wheel in time; As the front of the car's call turns in a new direction, it gradually regains alignment, allowing the vehicle to move forward.

At the same time, it is also possible to check the position of movement of the rear wheels by looking in the rearview mirror, i.e. when the rear wheels are about to cross the turning point, they return to the steering wheel.

Millions of car purchase subsidies.

The right-angle turn is an assessment point in subject 2 of the driver test, which assesses the ability of the motor vehicle driver to correctly control the steering, accurately judge the inside of the vehicle, and dismantle the difference between the outer wheels when driving the vehicle on a rapidly changing road section.

Right Angle Turning Site Requirements:

The right-angled turning field looks like an L lying flat on the ground. After the implementation of the new regulations, the road length of the right-angle turning site is equal to the length of the vehicle, and the road width is the wheelbase of small vehicles plus 1 meter.

Diagram of a right-angle turn:

Right Angle Turn Exam Tips:

The driving technique for right-angle turns is to enter the curve and stick the parking space to the right for about 30 to 40 cm with the right side line. When the first vertical bar of the left window coincides with a right angle, the steering wheel is killed to the left. The right side of the body is close to the right-angled edge line outside the world, and the left and right front door triangle windows are aligned with the inner and outer right-angle lines in the middle of the direction, and the car is back to the right at the right time.

2. When driving into the examination room, try to stick to the right side of the road;

3. Once the front curb is blocked by the hood, you should slam the direction to the left until you hit the end;

4. When you see the front of the car aligned with the exit, quickly turn the direction back to the right.

Right Angle Turn Test Criteria.

100 points will be deducted for any wheel pressing the edge of the road (20 points will be deducted for the original wheel extrusion edge line, and 100 points will be deducted for crossing the line.) The new standard search high standard extrusion edge has also been increased to 100 points. )

100 points will be deducted for stopping in the middle of the trip.