Can the Reiz car adjust the kilometers of one way?

Ruizhi. The car can adjust the number of kilometers per way. If you look at the dashboard or the trip computer, it is usually the switch of Tripa B.

One-way kilometres are a kilometre subtotal. REIZ is the name of Toyota's Mark X model in Japan, which was launched in October 2005 at Tianjin FAW Toyota.

Plant 2 and Crown share a common chassis and are equipped with the same six-speed automatic manual transmission as Crown. The Mark X is the successor to the Mark II, which has a front-rear-wheel drive design and is the third best-selling model among all Toyota models, second only to the Crown in terms of positioning.

Hello, take a look at the dashboard or whether there is an adjustment in the driving computer, which is generally the switch of Tripa B.

Trip A and Trip B are two odometers that function identically. It can be cleared, it is not the same as the total odometer (ODO). The odo cannot be cleared.

If a new car or A and B are cleared, if you don't touch it, the same count of both equals ODO.

When one of A or B has not cleared zero since the start of the new car, its count = total odometer

Application 1), when a counter is zeroed out from a starting point, the counter will show the mileage at the end.

Application 3), whether to record with A or with B is entirely up to you. Just remember why you cleared it at the time. (For example, I went from being very bored to running 5 kilometers now).

QPN is in development and large.

Through a series of questions to check the DAO table, check the development progress and problems in the development to avoid later changes. Similar to the Ford APQP Status Report.

QPN is also the abbreviation of strong mud discharge! Q The first letter of the strong word pinyin p The first letter of the word pinyin n The first letter of the mud word pinyin The strong sludge discharge is a device used to discharge the sedimentary sludge at the bottom of the oilfield sewage settlement tank It is composed of sewage discharge pipe, diffusion pipe, upper mixing pipe, lower mixing pipe, nozzle, mud collection room, suction cup, auxiliary drainage pipe, etc.

QPN, Volkswagen's new zero-piece pre-existing self.

Quality planning is a platform for regular communication with Volkswagen in the development of BAI, through a series of questions and checklists, check the development progress and problems in development, and avoid later changes. Similar to the Ford APQP Status Report, friends who have been with Ford should know.

QPN is the abbreviation of strong mud discharge! q "Strong"The first letter of the word pinyin, p"Platoon"The first letter n of the word pinyin"Inside the mud"The first letter of the word pinyin is used for.

A device that can accommodate the sedimentation of sludge at the bottom of the oilfield sewage sedimentation tank. It is composed of sewage pipe, diffusion pipe, upper mixer, lower mixer, nozzle, mud collection chamber, suction cup, auxiliary discharge pipe, etc.

QPN strong sludge discharge, a new type of sludge discharge equipment for oilfield oil production plants, joint station settling tanks, settling tanks, and sewage oil tanks, which can replace manual tank clearance.

As of 2019, automobile-related accessories are available.

As of 2019, the relevant departments have not been strictly inspected, but from the perspective of the interests of the user's operating company, it is recommended to operate automobile equipment, and the profit margin of automobile equipment is large.

Some common parts used by parts companies should be had, but it is recommended not to operate parts related to the safety performance of automobiles, and the user's company is mainly sales-oriented.

In fact, the relevant departments are not strictly inspected now, but from the perspective of the interests of your operating company, it is recommended to operate car equipment, and the profit margin of automobile equipment is large. Of course, as a parts company, some common and commonly used parts should be there. However, it is recommended not to deal in parts related to the safety performance of automobiles, one is that your company is mainly sales, which means that you lack professionals in automobile maintenance, and second, the parts and components linked to automobile safety have to bear certain risks.

Automobile-related accessories can be loosely managed.

In the past five years, a number of Japanese parts manufacturers have been exposed to fraud.

The reporter noticed that in the past few years, the problem of "counterfeiting" of Japanese auto parts companies and car companies has occurred frequently. Due to the exposure of counterfeiting, Japanese parts giants and Japanese car companies were caught in large-scale recalls. Due to quality defects, Japanese parts giants and Japanese car companies have also encountered trouble.

According to the data, in 2017, Japan's Kobe Steel was exposed to the strength and other performance data of aluminum products that were tampered with, and many Japanese car companies such as Toyota used the product. In 2017, Subaru admitted that in the past 30 years, the company's two factories used unqualified inspectors to "fool" the vehicle inspection of new vehicles before leaving the factory, recalling 10,000 vehicles, and Subaru President Yasuyuki Yoshinaga bowed and apologized at a press conference. In 2020, the Japanese auto parts giant "Denso Corporation" caused the vehicle to stall during driving due to a defect in the fuel pump produced, and many Japanese car companies were affected, resulting in Toyota, Honda, Subaru, Mazda and other car companies accumulating more than 5 million vehicles being recalled.

In the Chinese market, some of the Japanese joint ventures involved have also announced large-scale recall plans for this reason.

1. Engine parts.

Cylinder heads, airframes, oil pans, etc.

Crank connecting rod mechanism: piston, connecting rod, crankshaft, connecting rod bearing, crankshaft bearing, piston ring, etc.

Valve mechanism: camshaft, intake valve, exhaust valve, rocker arm, rocker arm shaft, tappet, push rod, etc.

Air intake system: air cleaner, throttle, intake resonator, intake manifold, etc.

Exhaust system: ternary catalyst, exhaust manifold, exhaust pipe.

2. Drive train accessories.

Flywheels, pressure plates, clutch plates, transmissions, shift control mechanisms, transmission shafts (universal joints), wheel hubs, etc.

3. Brake system accessories.

Brake master cylinder, brake cylinder, vacuum booster, brake pedal assembly, brake disc, brake drum, brake pad, brake oil pipe, ABS pump, etc.

4. Steering system accessories.

Steering knuckles, steering machines, steering columns, steering wheels, steering levers, etc.

5. Driving system accessories.

Steel rims, tires.

Suspension class. Front axle, rear axle, swing arm, ball joint, shock absorber, coil spring, etc.

6. Ignition accessories.

Spark plugs, high-voltage wires, ignition coils, ignition switches, ignition modules, etc.

7. Fuel accessories.

Fuel pumps, fuel pipes, fuel filters, fuel injectors, oil pressure regulators, fuel tanks, etc.

8. Cooling system accessories.

Water pumps, water pipes, radiators (tanks), radiator fans.

9. Lubrication system accessories.

Oil pump, oil filter, oil pressure sensor.

10. Electrical instrument accessories.

Sensors, lamps, ECUs, switches, air conditioners, wiring harnesses, fuses, motors, relays, horns, actuators.

Lamps and lanterns Decorative lights, anti-fog lights, indoor lights, headlights, front turn signals, side turn signals, rear combination lights, license plate lights, all kinds of bulbs.

Switches. Combination switches, glass lifting switches, temperature control switches, etc.

Air conditioners. Compressors, condensers, drying bottles, air conditioning tubes, evaporation tanks, blowers, air conditioning fans.

Sensors. Water temperature sensor, inlet air pressure sensor, inlet air temperature sensor, air flow meter, oil pressure sensor, oxygen sensor, knock sensor, etc.

11. Other accessories: airbags, seat belts, etc.

The test equipment for auto parts generally includes: sand and dust test chamber, rain test chamber, sandblasting test chamber, water test device, and vibration table vibration.

1.Low temperature environment.

The low temperature environment will cause physical shrinkage, oil solidification, reduction of mechanical strength, embrittlement of materials, loss of elasticity and icing of automobile parts, and the corresponding automobile will have cracks, mechanical failures, increased wear, sealing failures and poor insulation of circuit systems. The equipment used in the use is: high and low temperature test chamber, low temperature test chamber.

2.High temperature environment.

The high-temperature environment will produce thermal effects, which will cause softening, expansion and evaporation, gasification, cracking, melting and aging of automobile parts, and the corresponding automobile will have mechanical failures, lubrication seal failures, poor circuit system insulation, mechanical stress increase and strength weakening and other failures. The equipment commonly used includes high and low temperature test chambers, high temperature aging chambers, precision ovens, etc. For example, rubber products on automobiles, including floor glue, rubber on electronic components, etc.

3.Hot and humid conditions.

The environmental humidity will cause the deterioration of the material produced on the metal surface, the reduction of electrical strength and insulation resistance, and the degradation of electrical properties. The equipment commonly used is: constant temperature and humidity test chamber, high and low temperature damp-heat alternating test chamber.

4.Low air pressure conditions.

The low air pressure effect can degrade engine and emission performance, resulting in difficult start-up, unstable operation, seal failure, and reduced electrical performance. The equipment commonly used is: high and low temperature and low pressure test chamber.

5.Radiation conditions.

Solar radiation produces heating and photochemical effects that cause aging, embrittlement, expansion, softening, stickiness and seal failure. The equipment commonly used is: ultraviolet aging test chamber, xenon lamp aging test chamber, ozone aging test chamber.

6.Sand and dust environment.

The sand and dust environment is easy to cause wear and tear of parts and gambling plugs, which makes the filter fail and the electrical sealing performance is reduced. The equipment commonly used is: sand and dust test chamber.

7.Rainwater environment.

The rainwater environment will produce a landing and infiltration effect, which can easily cause the engine to stall, the electrical equipment to fail, and accelerate the corrosion of the metal surface. The equipment commonly used is: rain test chamber.

8.Salt spray environment.

Salt spray environments can cause chemical reactions that reduce mechanical strength, corrosion of materials, and changes in electrical properties. The equipment commonly used is: salt spray corrosion test chamber. For example, metal products include electroplating parts for automobiles, screws, nuts (including building materials) and other plating parts.

Environmental Reliability Testing.

High temperature test (can with IR).

Low temperature test: Hemperature & humidity test (can with IR).

Condensation test, low pressure test, thermal shock test, dust & water resistant test, salt spray test

Car, rickshaw, motor vehicle, car, bicycle, electric car, spark plug, manual transmission, gasoline, spare tire, recorder, auto parts can do 710 some environmental testing?

In a certain period of time, most of the domestic auto parts enterprises have low sales volume, and the sales volume is as high as 10 billion US dollars.

Compared with Zhitou, the scale of China's auto parts DAO enterprises is obviously small. Moreover, China's manufacturing exports have always been known for being cheap, and large multinational enterprises have not only transferred manufacturing links to low-cost countries and regions on a large scale to open up emerging markets in order to effectively reduce production costs, but also gradually extended the scope of transfer to R&D, design, procurement, sales and after-sales service, and the scale of transfer is getting larger and higher. With the change in the organizational structure of the auto parts industry, more and more automakers will implement global procurement of parts.

However, China's huge manufacturing industry and the characteristics of high quality and low price are unlikely to change in a short period of time, so auto parts will still be exported and internationalized as the main theme in the future. The development of new technologies for auto parts presents the following major trends: the depth of development is deepening; The degree of generalization and standardization of parts and components has been improved; The level of electronic and intelligent parts has been improved; The lightweight of vehicles and parts has become the future development trend; Clean and environmentally friendly technology has become the commanding heights of future industrial competition.

In a certain period of time, China's auto parts industry still has many deficiencies, such as poor industrial foundation, unreasonable structure, insufficient research and development and lack of famous brands.

In recent years, China's automobile industry has maintained rapid development, and the demand scale of the auto parts market has also grown rapidly. The construction of the auto parts industrial park has become an effective means for the local government to stimulate economic growth and promote industrial agglomeration. The "2015-2020 China Auto Parts Manufacturing Industry In-depth Market Research and Investment Prospect Analysis Report" released by the Prospective Industry Research Institute.

Prospect research shows that in recent years, the investment in the automobile industrial park has shown the characteristics of large area, large investment amount and wide coverage, only in 2013, there are a number of parts industrial parks with an investment of 10 billion yuan to start construction or will be built. For example, Xiantao Jianhuazhong Auto Parts Industrial Park, with an initial investment of 5 billion yuan, will have a total investment of more than 20 billion yuan in the next four years; Hangzhou Economic Development Zone has built an auto parts industrial park, with an investment scale of more than 10 billion.

The inevitable result of large-scale investment in the auto parts market is the large-scale growth of parts output value and sales revenue. According to the research of the Prospective Industry Research Institute, from 2005 to 2012, the output value of China's auto parts increased from 401.7 billion yuan to 2,661.9 billion yuan, with a compound annual growth rate of 100.7 billion yuan; The sales revenue of auto parts increased from 100 million yuan to 100 million yuan, with a compound annual growth rate.

The rapid expansion of the scale of the auto parts industrial park will lead to the intensification of competition in the entire auto supporting market, which will cause the decline in profits of the entire industry. How to digest such a large output and promote the benign development of the auto parts industrial park has become a problem that needs to be solved by the local government. At the end of November 2013, Guangdong Province held the "2013 Guangdong Auto Parts Industry Investment Promotion Conference" to create a global investment promotion platform for auto parts, of which 6 auto parts industrial parks also actively participated, finding an effective model for the auto parts industrial park.

With the globalization of the automobile production market, auto parts resources have also begun to be allocated globally. As a big country in the automobile industry, China's export market for auto parts has gradually opened. In 2012, the export value reached 100 million US dollars, of which the export value of auto parts, accessories and body reached 100 million US dollars, a year-on-year increase.

Forward-looking analysis believes that the "2013 Guangdong Auto Parts Industry Investment Promotion Conference" held by Guangdong Province has made a demonstration for the domestic auto parts industrial park. In the next few years, global investment will become an inevitable choice for the development of auto parts industrial parks. Through global investment, the contradiction between supply and demand in the domestic market can be solved and the competition between enterprises can be reduced.

At the same time, it can also expand the overseas market share of domestic parts enterprises and improve the visibility of enterprises.