What is the installation method of the floor drain joint of the washing machine? How to choose a flo

Nowadays, there are many types of floor drains, and explosion-proof floor drains are a very important category. Of course, if you install an explosion-proof floor drain at home, it is completely fine. Many people like to buy and use explosion-proof floor drains, but buy home but do not know how to install, this article collects information, introduces the installation method and steps of explosion-proof floor drains, and also introduces the installation precautions of explosion-proof floor drains.

1. Introduction to the installation steps of explosion-proof floor drain.

First of all, find a good slope of the flowing water to ensure that the water can flow in all positions, leave the tiles on the edge of the floor drain, measure the size, cut the notch, and achieve the perfect effect. Cut the tiles and lay them on, such as the size of the floor drain 10cm x 10cm to cut to the right one, and leave a little gap appropriately. Brush the back of the floor drain with cement and mud around it to make it firmly bonded to the ground.

Don't brush too much. The center of the floor drain is facing the center of the drain pipe, put it into the pipe, and press the floor drain level slightly below the tile surface. Wipe off excess cement and remove rubbish from the floor.

Close the panel lid and the installation is complete. After the cement is dry, the floor drain core is installed, and the floor drain core can be taken out and cleaned at any time.

2. Introduction to the precautions for the installation of explosion-proof floor drains.

After the construction is completed, don't forget to seal the side seams; The installation of floor drain is more complicated, so it must be completed by professionals; Trim the drainage reserved holes to make them completely consistent with the floor drain bought, because the reserved holes for drainage are relatively large when the real estate developer delivers the house. Among them, the opening aperture of the floor drain grate should be controlled between 6-8mm, which can prevent the entry of hair, sludge, sand and other dirt;

It should be grasped that the water inlet of the multi-channel floor drain should not be too much. Multi-channel floor drain is a product developed in recent years, and a body usually has 3 to 4 water inlets (for washbasins, bathtubs, washing machines, and floor drainage), which not only affects the drainage volume of the floor drain, but also does not conform to the actual design situation. Therefore, the water inlet of the multi-channel floor drain should not be too much, and there are two (floor and bathtub or floor and washing machine) can fully meet the needs.

Floor drain installation step method.

Washing clothes easily should be more cautious when installing floor drains, do you know how to install washing machine floor drains? Although the steps of installing the washing machine floor drain are very simple, if you want to present the best effect, then you should pay attention to these places when installing the washing machine floor drain, and what problems should be paid attention to when installing the washing machine floor drain? In the home, floor drains are quite widely used, especially washing machine floor drains .

In order to wash clothes easily in the future, you should be more cautious when installing the floor drain, do you know how to install the floor drain of the washing machine? Although the steps of installing the washing machine floor drain are very simple, if you want to present the effect, then you should pay attention to these places when installing the washing machine floor drain, and what problems should be paid attention to when installing the washing machine floor drain?

How to install the floor drain of the washing machine?

1. There are many types of floor drains, and here we introduce a simple model, which does not require special tools to install; Look at the main body, there is mainly a sealing core, which is used to pass the water while preventing the odor from drifting in reverse, the adapter is used to connect the floor drain and the washing machine drain pipe, and the floor drain cover is used to connect the adapter and the sealing core.

2. First of all, take out the small sealing ring and put it into the upper end of the floor drain cover, which is used for sealing when the adapter and the floor drain cover are connected to prevent water leakage.

3. Unscrew the adapter nut, then align it with the floor drain cover, and tighten the connection between the two.

4. Pull out the sealing ring of the water at the lower end of the floor drain cover and remove it.

5. Put the sealing core in the place where the water outlet at the lower end of the floor drain cover, and then the sealing ring passes through the core and is screwed back on.

6. The main body of the floor drain has been installed, and the sealing ring connected to the washing machine drain pipe at the other end of the adapter is removed.

7. Then the sealing ring is first installed into the drainage pipe, and the floor drain is screwed on to connect the two.

8. In this way, the floor drain and the washing machine drain pipe are connected, and the angle is rotated so that the floor drain can cover the sewer pipe, so that it is OK.

What problems should be paid attention to when installing a washing machine floor drain?

1. Trim the reserved hole for drainage so that it is completely consistent with the floor drain that is bought, because the reserved hole for drainage of real estate developers is relatively large when handing over the house. The opening aperture of the floor drain grate should be controlled between 6 and 8mm, which can prevent the entry of hair, sludge, sand and other dirt.

2. In the bathroom, the floor drain of the washing machine in a plane will always be in the position, and the slope is 1 2 degrees compared with the position, so that the smaller water can be discharged into the floor drain.

After reading the above content, I believe you should already know how to install the floor drain of the washing machine! If you want to make the floor drain last longer, then you must know how to clean the floor drain, so that there will be no water blockage. What problems should be paid attention to when installing a washing machine floor drain?

Be sure to pay attention to the steps, the specific installation method, the staff will give you a detailed introduction or they will directly come to the door to install, so don't worry that you can't.

The washing machine is not able to achieve satisfactory results in the later stage and many factors are inseparable, first of all, the choice of products, followed by the correct installation method and the reference and purchase of some spare parts. Starting from this, we can know that one aspect, the special floor drain of the washing machine is often different from the ordinary floor drain, they can be coordinated with the hose of the washing machine, and secondly, the appropriate floor drain can maximize the value of the product through the correct installation.

1. Installation method of special floor drain for washing machine

1. First of all, correct the reserved drainage holes. In order to avoid hair, grit and other stains from entering the pipe, causing blockage, etc., it is necessary to correct them first to ensure that the orifice is completely consistent with the interface bought. At this time, tools such as chisels or hammers are needed to deal with it, and the opening diameter of the floor drain grate should be kept between 6-8mm.

2. The terrain should be low. In the bathroom, the floor drain of the washing machine should be in the lowest position, so as to ensure the smooth discharge of sewage. Attention should also be paid to this in the installation of joints, in general, it is enough to have an inclination between 1 and 2 compared to the highest position.

It should not be on high ground, otherwise it will be difficult to remove sewage or overflow the bathroom.

Second, the purchase of professional floor drain of washing machine

1. Observe the structure. There is a difference between the professional floor drain of the washing machine and the ordinary drainage floor drain, in terms of structure, the professional floor drain will have a hole on the surface in order to facilitate the insertion of the drainage pipe, while the ordinary floor drain does not. When purchasing, you should pay attention to the selection and observation, and choose the right floor drain for washing machines.

2. Look at the material. The floor drain of the washing machine is divided into two types: the water seal floor drain and the air seal floor drain, of which the air seal floor drain is direct drainage, which is more suitable, because it can meet the maximum displacement of the washing machine. When purchasing, you need to pay attention to the material of the floor drain.

At present, there are various materials on the market, and the quality will be different in the past, among which stainless steel and copper alloy floor drains are more cost-effective and the most widely used.

3. Look at performance. The instantaneous water output of the washing machine will be a lot, so the requirements for drainage performance are high, and you should pay attention to the speed of draining when purchasing. In addition, it is also necessary to consider the brand of the product, generally a good brand is better in the quality, workmanship and drainage performance of the floor drain, and it is also reliable to use.

The above recommendation for you is a common and special floor drain, that is, a special floor drain for washing machines, so how should it be installed? What are the precautions that need to be focused on understanding and analyzing in the process of operation? Through the example, it can be seen that the special floor drain of the washing machine has a certain arc, which can be coordinated with the hose of the washing machine.

In this way, it can discharge sewage in time and will not affect the surrounding floors and furniture, and there are many precautions for reference in the installation process of this floor drain, which you can learn from the above.

You can get it for free

Although the floor drain of the washing machine is a small part, but a big problem, we often encounter such a problem, the size of the washing machine drain and the floor drain do not match, resulting in the inability to plug in, every time the washing clothes are released, it will spread out, flowing everywhere, so that many people are very distressed. Therefore, let's introduce how to choose the floor drain of the washing machine and the installation method of the floor drain of the washing machine.

1. How to buy a floor drain for washing machines.

1. Select the floor drain to see the material.

Now there are mainly cast iron, PVC, zinc alloy, ceramic, cast aluminum, stainless steel, brass, copper alloy and other materials on the market. Among them, stainless steel and copper alloy floor drains are moderate, beautiful and durable; Brass floor drain has the best performance in all aspects.

2. Select the floor drain to see the launching speed.

The space in the drain is large, and the water flow is not obstructed, and the core head ridge leaks quickly, so you can choose it when purchasing.

3. The selection of the floor drain casing of the washing machine is changed to seepage.

There are single and double pipes for washing machine floor drain casing, and the washing machine can drain directly to the floor drain. Tee-double pipe is to realize 2 washing machines, or the washing machine and the pier cloth pool are drained together, and the single pipe is dedicated to washing machines.

Second, the installation method of washing machine floor drain.

1. Trim the reserved hole for drainage so that it is completely consistent with the floor drain that is bought, because the reserved hole for drainage of real estate developers is relatively large when handing over the house. The opening aperture of the floor drain grate should be controlled between 6 and 8mm, which can prevent the entry of hair, sludge, sand and other dirt.

2. The floor drain of the washing machine in a plane of the bathroom must always be in the lowest position, and the slope is 1-2 degrees compared with the highest position, so that smaller water can be discharged into the floor drain.

1.Introduction to the special interface of the floor drain of the washing machine.

The special interface for the floor drain of the washing machine is an important part that connects the washing machine and the drainage pipe, which is used to prevent water leakage and ensure the normal use of the washing machine. Now there are many models of washing machine floor drain special interfaces on the market, which can be selected according to different needs.

2.Precautions before installing the special interface for the floor drain of the washing machine.

Before installing the special interface for the floor drain of the washing machine, you need to pay attention to the following:

1.Locate the outlet of the waste pipe and make sure that the dedicated interface for the floor drain of the washing machine matches the outlet.

2.Make sure that the distance between the special interface of the floor drain of the washing machine and the drain pipe meets the standards on the installation instructions of the washing machine.

3.Before installing the special interface for the floor drain of the washing machine, it is necessary to move the washing machine to the installation position and connect the power supply and water inlet pipes.

4.During installation, it is necessary to ensure that all connecting parts are tight and secure, and that no water leakage occurs.

3.The installation steps of the special interface for the floor drain of the washing machine are molded.

Follow the steps below to install the special interface for the floor drain of the washing machine:

1.Insert the special interface of the floor drain of the washing machine into the drain of the washing machine, and rotate the interface to fix it.

2.Insert the connecting pipe into the outlet pipe above the special connection for the floor drain of the washing machine and tighten it.

3.Insert the connecting pipe into the outlet of the wastewater pipe and screw it tight.

4.Make sure all connecting parts are securely fastened and there are no water leaks.

5.Move the washing machine back to its installation position and connect the power supply and water inlet pipes.

4.Maintenance of the special interface for the floor drain of the washing machine.

The special interface of the floor drain of the washing machine needs to be kept clean during use to avoid blockage caused by not cleaning for a long time. It is recommended to clean up every once in a while, and the specific steps are as follows:

1.Disassemble the special connection and connection pipe of the floor drain of the washing machine and clean all the parts.

2.Inspect the connecting pipes for cracks or other damage, and replace them if necessary.

3.Check the special interface of the floor drain of the washing machine for foreign objects or blockages, and clean or replace it if necessary.

4.Reinstall all parts and secure them tightly.

5.Recommendations for the purchase of special interfaces for floor drains for washing machines.

Before buying a special interface for the floor drain of the washing machine, you need to choose according to your washing machine model and the caliber of the drain pipe. At the same time, the following points need to be noted:

1.Product quality: Choose a brand with better quality to avoid accidents such as water leakage.

2.Material: The special interface of the floor drain of the washing machine can be made of plastic or metal, of which the plastic material can prevent oxidation and have a longer service life.

3.Installation method: You can choose to install it by yourself or ask professionals to install it to ensure the quality and effect of installation.

6.Summary.

The special interface of the floor drain of the washing machine is a key component to ensure the normal use of the washing machine, and the correct installation and maintenance can prolong its service life. When purchasing a special interface for the floor drain of the washing machine, you need to pay attention to factors such as product quality, material and installation method to meet your own needs.