What happens when the air conditioner stops after a while?

The reasons why the air conditioner stops after blowing for a while are as follows: 1. The air conditioner reaches the set temperature standard. When the air conditioner reaches the set temperature standard, the air conditioner will stop supplying air, which is a power-saving mechanism of the air conditioner, and it can be resumed only after the temperature rises again.

2. The position of the air conditioning baffle is incorrect. Some users will not be able to reach the standard due to the incorrect position of the baffle of the air conditioner during the use of the air conditioner, but because the air conditioner has its own thermostat, the temperature around the air conditioner will automatically shut down when it reaches the set standard, and the position of the baffle needs to be adjusted. 3. The air conditioner is in defrosting work.

Because the air conditioner will frost due to heat exchange when the air conditioner is heating, the air conditioner will automatically defrost after working for a period of time, and the internal unit will not continue to supply air at this time, so the air conditioner will shut down.

There may be: 1. The automatic mode may be turned on, and when the set temperature is close to the room temperature, it will stop when the set temperature is reached. It creates the illusion of failure when it is turned on and stops, but there is no problem with the actual air conditioner.

2. The voltage is abnormal and unstable. Compressor overcurrent protection. It is recommended to try a different voltage stabilizing device.

3. The temperature of the indoor coil is too high, resulting in protective shutdown. When the indoor temperature is 26 degrees Celsius and the outdoor temperature is above 20 degrees, the air conditioner cannot heat normally, which is easy to cause protection.

4. The failure of the indoor fan causes no blowing and protects the shutdown. If the outdoor fan fails, causing serious frosting, defrost is carried out, and the indoor air prevention function is entered.

Check whether the power supply voltage is normal, if there is no problem, it may be that the air conditioner is protected, clean the condenser of the external unit.

After the air conditioner is turned on, it will stop for a while, there may be an alarm, you have to see the alarm**.

1. There is no problem with the air conditioner, it is the self-protection function that is working. At present, most air conditioners have automatic protection function, which means that frequent power on and off will seriously affect the life of the air conditioner, and it will not pay attention to you. The normal operation should be after shutting down, at least three minutes before turning on the machine normally.

2. The power module is broken and needs to be replaced. The basic methods for judging the common faults of household air conditioners are: looking, listening, touching, measuring and analyzing.

a. Look: Carefully observe the situation of each component of the air conditioner, focusing on the three parts of the refrigeration system, electrical system and wind system, and judge whether they are normal. Refrigeration oil), you can also use a clean soft cloth and soft paper to wipe the connection between the pipe weld and the joint, and observe whether there is oil stain to judge whether there is leakage.

b. Listen: Turn on the power and listen carefully to whether the sound of the air conditioner compressor is normal, whether there is abnormal sound, whether there is noise in the operation of the fan, whether the noise is too loud, etc. In the operation of the air conditioner, the vibration is slight and the noise is small under normal circumstances, generally below 50db.

If the vibration and noise are too large, the possible reasons are: foam plastic pads, etc., which can make the vibration of the air conditioner increase and the noise becomes louder during operation.

c. Touch: touch the relevant parts of the air conditioner with your hands to feel its cold, heat, vibration, etc., which is helpful to judge the fault quality and location. Under normal circumstances, the degree of the condenser is gradually decreasing from top to bottom, and the degree of the lower part is slightly higher than the ambient degree.

If the whole condenser is not hot or the upper part is slightly hot, or although it is hot, there is a significant difference in the degree of the upper and lower adjacent pipes, it is abnormal. Under normal circumstances, if you put your finger dipped in water on the surface of the evaporator, it will feel cold and sticky.

d. Measurement: In order to accurately judge the quality and location of the branch fault, it is often necessary to measure the energy parameters and status of the air conditioner with instruments and meters. If there is any refrigerant leakage with the leak detector; Use a multimeter to measure whether the power supply voltage, the current to the ground at each terminal and the operating current meet the requirements, and the air conditioner controlled by the computer should also measure whether the potential of each control point is normal.

e. Analysis: Most of the results of the above means can only reflect a certain state of the department. The various parts of the air conditioner are mutually influencing each other, and a fault phenomenon may have multiple causes, and a cause may also produce a variety of failures.

Therefore, it is necessary to conduct a comprehensive comparative analysis of the local factors, so as to comprehensively and accurately determine the quality and location of the fault.

Check that the timer switch option on the aircon remote control is turned on. If yes, turn it off.

Or check if the remote control is in sleep mode, when the temperature reaches the adjusted temperature, the remote control will automatically turn off, and the mode will be converted to normal mode.

If all the above methods have been tried and still do not solve the problem, then we must check if there is a problem with the manual switch, which is as follows:

I suggest you look at the air conditioner emergency switch (manual switch), (some are on the panel inside the machine, some need to open the panel to see the internal machine), unplug the power supply, pick it up with your hand and go back and forth, probably the reason why it is not reset.

The air conditioner will stop automatically when it is turned on.

This could also be due to poor contact between the pins and sockets of the air conditioner lines. You can try unplugging the air conditioner switch and plugging it into a different pin to see if it turns off automatically.

Grid voltage can lead to other types of air conditioners:

Due to the automatic protection function of air conditioners against overvoltage and undervoltage, they will automatically shut down when the grid voltage is unstable beyond the allowable range. If this happens frequently in the grid, air conditioning cannot be used. It can only be solved by the power supply department.

It is impractical to install a voltage regulator, it is very expensive to drive an air conditioning regulator (to 5-10 kVA), and the voltage regulator itself has its own range of adaptation, the power grid fluctuates too much, it cannot be tuned, and thus appears in the automatic shutdown of the air conditioner.

Finally, when you can no longer solve this problem, you need to find a sales service. Have a professional maintenance personnel check the internal circuit of the air conditioner to see if it is an abnormal operating parameter. Only on-site inspections are the most specific. It is also the most authoritative.

The air conditioner will stop automatically when it is turned on.

It is recommended that people need to open the windows for ventilation again, and generally need to open the windows for ventilation for 15 minutes. At the same time, people need to exercise more. The nameless swollen air-conditioned room is closed, the air is not circulated, there is no fresh air to replace, and if you catch a cold, there will be a large number of cold viruses in the room.

In such an environment, the virus can be easily inhaled into the body. Frequent opening of windows to ventilate the air is conducive to indoor air circulation, dilute the concentration of viruses, and reduce the chance of cold transmission; At the same time, it is necessary to strengthen one's own immunity and do regular aerobic exercises, such as cycling, brisk walking, mountaineering, swimming, etc. To boost immunity and prevent colds, drinking enough water not only helps eliminate dryness but also reduces the number of cold viruses in the body.

Therefore, drink at least eight glasses of water or a certain amount of fruit juice a day.

Hope it can help you, satisfied. Thank you.

Check whether a scheduled shutdown is set.

If you have set the automatic scheduled shutdown, it will be turned off at a timed after it is enabled.

Causes of compressor overheating.

The external unit should be cleaned first, and the external unit is most afraid of dirty. Dust gets stuck in the heat sink, which will cause poor heat dissipation and overheating of the compressor protection.

Problems with the cooling fan of the external unit can also cause poor heat dissipation.

If there is a problem of failure in the machine, you should contact after-sales or professional maintenance personnel for on-site repair in time, and it is best not to repair it yourself without relevant experience.

Why does the air conditioner stop after a while, stop and turn on again?

Here's what could be the reason: Auto mode may be turned on. When the set temperature is close to room temperature, the machine stops when the set temperature is reached.

Causing the illusion of failure to stop driving for a while, the actual air conditioner is no problem. The voltage is abnormal, unresponsive and stable. Compressor overload protection is grinding.

It is recommended to try replacing a voltage regulator. 3. The temperature of the indoor coil is too high, resulting in protective shutdown. When the indoor temperature is 26 and the outdoor temperature is above 20, the air conditioner cannot be heated normally, which is easy to cause protection.

Failure of the indoor fan, resulting in no blowing and protection shut-off. The outdoor fan is faulty, and the frost is severe. Perform defrosting and enter the room air protection function.

1.Auto mode may be enabled. When the set temperature is close to room temperature, the machine will stop working at the set temperature.

Causing the illusion of failure to stop driving for a while, the actual air conditioner is no problem. The voltage is abnormal and unstable. Compressor overload protection.

It is recommended to try replacing a voltage regulator. 3. The temperature of the indoor coil is too high, resulting in protective shutdown. When the indoor temperature is 26 and the outdoor temperature is above 20, the air conditioner cannot be heated normally, which is easy to cause protection.

Failure of the indoor fan, resulting in no blowing and protection shut-off. The outdoor fan is faulty, and the frost is severe. Perform defrosting and enter the room air protection function.

Summary. Dear, according to the encyclopedia related information query, the reason why the air conditioner stopped for a while was 1Indoor temperature conditions, according to the needs of the environment to set the temperature of the air conditioner, once the air conditioner set the temperature benchmark, there will be the phenomenon of the air conditioner stopping the air supply, only need to increase the set temperature of the air conditioner, after a while the air conditioner will continue to work.

2.Caused by the defrosting of the air conditioner, the air conditioner is heated by the heat exchange of the outside air and frosts, and the air conditioner will automatically defrost after running for a certain period of time. Hope it helps.

Dear, according to the encyclopedia related information query, the reason why the air conditioner stopped for a while was 1Indoor temperature conditions, according to the needs of the environment to set the temperature of the air conditioner, once the air conditioner set the temperature benchmark, there will be the air conditioner stop the air supply of the phenomenon of the year, only need to increase the air conditioner set temperature, after a while the air conditioner will continue to work. 2.

The defrosting of the air conditioner starts from the side gear, the air conditioner is heated by the heat exchange of the outside air and frosts, the air conditioner will automatically defrost after running for a certain period of time, at this time, the internal machine does not continue to supply air, so it stops working, but after the defrosting is over, it starts working again. Hope it can help you

Dear, according to the encyclopedia related information query, I hope it can help you.

Pro,According to the encyclopedia related information query,The reason why the air conditioner is turned on for a while and stops the source of the tour is 1.Indoor temperature conditions, according to the needs of the environment to set the temperature of the air conditioner, once the air conditioner set the temperature benchmark, there will be the phenomenon of the air conditioner stopping the air supply, only need to increase the set temperature of the air conditioner, after a while the air conditioner will continue to work. 2.

Caused by the defrosting of the air conditioner, the air conditioner is frosted by the heat exchange of the external air when the heating is cracked, and the air conditioner will automatically defrost after running for a certain period of time, at this time, the internal machine does not continue to supply air, so it stops working, but after the defrosting is over, it starts working again. Hope it helps.

Summary. Hello dear, the air conditioner will automatically stop after a while, because the current air conditioner is basically inverted, as long as the set temperature is reached, it will automatically stop, but it can bring the effect of saving electricity. If this is the case, the indoor temperature is relatively high and has reached the temperature of the air conditioner you set, so you don't have to worry about it being normal.

2. It is also possible that we have set the timing function of the air conditioner, such as automatically turning off after an hour or two hours, and it may stop automatically after a while. If this is the case, you need to select the timer switch off through the remote control. 3. It is also possible that the remote control is in sleep mode, if the temperature is reached, the remote control will automatically turn off, and convert it to normal mode, which is also a normal phenomenon<>

<> the air conditioner turned on and stopped by itself for a while.

About 10 minutes after the air conditioner was turned on, it shut down by itself, what is the reason?

Hello dear, the air conditioner will automatically stop after a while, because the current air conditioner is basically inverted, as long as the set temperature is reached, it will automatically stop, but it can bring the effect of saving electricity. If this is the case, the indoor temperature is relatively high and has reached the temperature of the air conditioner you set, so you don't have to worry about the normal phenomenon base state. 2. It is also possible that we have set the timing function of the air conditioner, such as automatically turning off after an hour or two hours, and it may stop automatically after a while.

If this is the case, you need to turn off the timing switch through the remote control. 3. There is also a respectable hall can be the remote control is in sleep mode, if the temperature after the setting is reached, the remote control will automatically turn off, and convert it to normal mode, this is also a normal phenomenon<>

<> there is a blockage problem in the pipeline, such as once the connecting pipeline or outdoor pipeline is blocked, the slag will cause the whole system to be unable to return oil normally, that is, the cold enzyme direction, resulting in excessive pressure and the problem of stopping the compressor, and then the transportation hall will automatically start.

It stopped before I could reach the temperature I set.

Plumbing check it out.

It is common for a pipeline to have problems leading to downtime.

You can clean the pipes.