Bandai Gundam BB Fighter Coloring Problem 30

1.Of course, this is a must-know to get started.

2.。In terms of technology, the technical airbrush spray paint, the bad one, wash and brush...

3.There is it in the manual.

4。Dedicated to sanding, it can eliminate the nozzle, and it can help with coloring when sanding the whole (there are several kinds of it) Matting paint is recommended that you don't use it, he can improve the realism of Gundam, but it is difficult to master the amount (my Zagu died under his clutches...).

I wish you a speedy success o(o

1.Some can be used directly with a marker, and the technical ones can be used with bleeding threads.

2.The spray gun is more even, and the hand application is suitable for small parts.

3.See what you like.

4.Grinding is convenient for spray paint to adhere to coloring, and matting can reduce reflection after spraying.

1. GUNPLA always lusts over each part, dries it, and then assembles it.

2. That kind of pen is called a marker. It is normal to have different shades of pen painting, you must know that the surface of the plastic parts is very smooth, and as soon as the pigment flows, the uneven color will naturally appear.

Players with a livery have two options: hand painting and spraying. Hand painting, as the name suggests, is to paint with bare hands, generally buying a bottle of paint, diluting it with solvent and multiplying it in a palette with a model pen (similar to an oil paintbrush) to apply it to the surface of the part; The paint in the marker has been diluted and can be squeezed into a palette for use, and the parts are generally painted without a marker, and the color of the marker is relatively simple.

It should be noted that no matter how high the technique of hand painting is, the coloring will not be satisfactory. If you want to color evenly and beautifully, LZ can consider buying an air pump and an airbrush, spraying. Of course, these two add up to hundreds, but if you have been making a model for a long time and need to color, it is recommended to use spraying, and small details are supplemented by hand painting.

I also use a pen to paint Gundam, paint Gundam to paint one part by one, it is best to buy a fade pen, painted in the wrong place can be used to fade, by the way tell you how to fade, the fade than painted in the place to fade, painted with the sharpest place, and then wiped off with toilet paper, this step is repeated several times, until the basic fade, the fade pen and the paint pen you bought a brand, it is best to paint it at one time when painting Gundam, so as to avoid the color is too dark and too shallow, and wait for it to dry by itself after painting (it will be completely dry in 20 minutes,Slow to do it in twelve hours.,For example, white.,It takes almost a day to completely dry) And don't touch it after painting.,There's another way to paint one side of the part.,Wait for this side to dry and then paint the other side.,This is the method I summarized after painting Gundam.,I hope it's useful to you.。

First answer the last question of lz, but where to paint the model with a pen, due to the different speed and slow time of the paint drying, it looks natural and uneven, and the depth is not the same, so it has something to do with the pen itself and the feel of lz, and moreover, the marker is generally used to supplement the color in a small area, so it is recommended to use a spray can for a large area, about 30 yuan for a can, and it can be used for a long time to do bb, and as long as it has a feel, it is much more uniform than the pen. To answer the previous question, GUNPLA is almost always painted first and then put together according to the drawings when they are dry. If you are a newcomer to lz, the current model is generally done well, as long as it is done well, you don't need to spray paint and color, and you can also have a good effect with a hook pen.

Gundam's practical pencil will do just that. Small areas of the place of the complementary color with a marker. If you use a spray can, you should first spray paint and then seep the line, otherwise the line will be covered - I don't think you can use the varnish, if you really want to get it well, you should fill the soil with water as a whole.

In this way, there is a background color, and the paint color is good, but it is a little more troublesome. Finally, the spray is dulled.

Side C, for example, this is side A, this is side B, it's side C, it's actually used for transition, and it's not too stiff.

Airbrush investment is large, a set of low-end domestic also needs hundreds to 1,000 yuan of input brushwork, that is, you say that the hand-painted has fatal shortcomings, first of all, the brush painting will leave traces, in response to a large area of flat surface operations is likely to appear uneven paint division, hand-painted for some complex, and the pattern has high-precision requirements for the coloring operation can not be competent, because how smart the hand painting is after all human hands, deviations will always appear, and airbrush coloring is the use of various props and means of the way, Therefore, as long as the preparation is sufficient in advance, the effect will naturally be satisfactory.

The marker is not a tool that can be used to color the gunpla, and the number of GUNPLA parts of one MG is as high as 200 or more, and the marker is somewhat similar to a paint, which is just a pre-prepared paint prepared by the manufacturer in the general marker, and the marker is generally used to make up the color of the nozzle or a small area of parts.

In the end, you ask the novice what is the best way, I think the question itself is ambiguous: in that way should not be distinguished by newcomers or veterans, first of all, the most important thing is to see your enthusiasm for the production of models, if you plan to take it as an important hobby for long-term development, and secondly, if the economy allows, it is recommended to go directly into the airbrush tool, don't worry that you won't use it, this thing does not require a very high level of technology, look at the manual to the forum to post you can get started. If the economy does not allow it, you can consider starting with the brush, the brush painting is not only a disadvantage, playing well with the brush is definitely good for coloring, and some coloring (mostly involving the weathering effect) effect can only be completed by the brush.

However, it is not recommended to use pen painting to complete large models, such as models above MG specifications, ......

If you are a novice, we recommend a marker, which can be sprayed with a layer of protective paint after application

(1) Use an airbrush to matte the model. It is recommended to be around 50 100mm. As for the specific distance. It depends on the user's habits. ~~

2) The ratio of matting paint to solvent. Personally, I feel that it is after stirring well. Press 1 : 4 (one part paint: four parts solvent).

3) The cause of whitishness is that the solvent is too concentrated. Not thin enough.

So it will leave a layer of powder on the surface. Because matting paint is a resin-based paint. It contains a solvent solution.

If it is diluted and sprayed with an airbrush, the solvent will evaporate before being sprayed on the surface of the part. So the paint particles have not yet reached the surface of the model and the solvent has evaporated. You will find that the paint particles are large.

It's like a powder.

It is recommended to spray thinly several times. Then it is not easy to turn white. ~~

A little advice. Hope it helps. Please laugh. ~

It is usually 1:2 to 1:3 (1 represents paint), if it is Gaia's matting paint, be careful not to add too much solvent, it will become a varnish.

In addition to spraying, you can also use a marker pen for the model to paint directly, but the effect is very bad, and it is easy to see the traces of painting.

If you spray, you first need an airbrush, and the domestic S-130 can make do with it, and the better one is recommended to be the 289 airbrush, but it's more expensive.

Then you need an air pump, and you can't use it without an air pump pen.

Then you need clips and foam boxes, clamp and spray on the plugs, and cover the belt or something if you make a human shape.

Then it's time to paint, first of all, you need water to replenish the soil as a primer. 30 yuan a bottle. Then there is the ordinary model paint, and the solvent of the model paint is also necessary. Depending on what kind of paint you want to make, you can choose what kind of lacquer to use.

Electroplating also needs varnish, ordinary is to use matting paint, this is good with sprinkler irrigation.

In general, the main thing is the above things. In addition to this, there is another must: a gas mask.

Paints are highly toxic, especially oil-based paints, and spraying paint without protective measures will cause too much harm to the body. At the very least, wear a mask and spray it in a ventilated environment. Smelling too much paint is easy to get leukemia.