Why can my A10 dual core receive wireless routing signals but can t access the network?

Because you didn't enter the wireless password.

It is a matter of common sense that you can't use a broadband connection if you use wireless routing.

So, if your broadband connection works, you can't go up the wireless route.

First of all, you need to enter the settings interface of your wireless router and set up your broadband account and password in it. Then set the wireless password.

Then, on your computer's local connection, set the IP address of the same network segment as your wireless router.

If the IP of your route is yes. Just set it to if yes, set it to the subnet mask is the gateway is the IP of your router

In this way, you can surf the Internet at the same time on your computer and mobile phone. But remember, don't use a broadband connection on your computer.

Because the cable out of the cat is plugged into the LAN port of the router, there is no routing function, and only one device can dial up the Internet.

You need to add a switch to distribute the line out of the cat to IPTV and the router WAN port, and set the router WAN port to PPPOE mode, so that the router can automatically dial the number, so that the computers connected to the router can share an account to surf the Internet.

If you don't understand the router, you should be able to see it in a stupid way, one interface is connected to the network cable, and the other is used for device connection, so the network cable should be connected to the inter port, and then connected to the computer from any LAN port, and then open the browser to enter the router settings.

I've encountered this problem, and I have to use two home swappers or routers to solve it. The line out of the cat passes through the router 1, connected to the LAN port, and if it is connected to the WAN port, it will be GGsmecta. Then divide it into two cables, one for ITV and one for Internet access.

The one that goes online can be connected to Router 2 again, so that Router 2 is the same as being connected directly from the cat. For this point, I was tired of fighting.

You're wrong with this wiring method.。。 Use the router as a switch... The line out of the cat is connected to the WAN port, which is what you call the inter port, and then the computer TV is connected to any port of the LAN port.

Don't make a mistake about the input and output. It's not good to practice the line, you have to log in to the router for further settings, select PPPoe mode there in the WAN port settings, and enter the broadband account password. In this way, the router will automatically help you complete the dialing action,Computer TV can be connected directly through the router,And you don't need to dial again,At the same time, the router can output wifi signal,Mobile phones and other devices can also be networked。

The cable out of the cat must be connected to the inter port of the router, so that the router can dial up, and the computer connected to the wireless and LAN port can access the Internet after the dialing is successful. If the ITV is connected from the router, the dialing of the ITV and the dialing of the router are conflicting, and only one of the two can be used, so you also need to buy a switch. The network cable from the cat is connected to the switch, and the switch leads out two lines, one to the ITV and the other to the inter port of the wireless router.

Then enter the router settings, enter your home broadband Internet account and password in the router, and after the router is successfully dialed up, the wireless and the computer can be used. Please refer to the manual for the settings of the router.

It stands to reason that if you take the host away, it will not affect the router, you just think about the computer is not turned on, and your mobile phone is not the same as the wireless one. Now there may be a few points: one is that when you dismantle the host, the switch where the router is located is turned off, the second is that you change the order of the two routers, and the third is that the wireless function is turned off by you, check it yourself.

Computers and networks are two different things, and they have nothing to do with each other.

You still need to start with the router to find the problem, first see if the egress router is normal, try to surf the Internet through the egress router, at least you can log in and see the running status, according to your exit ISP. After making sure that the egress router is normal, check the secondary router again.

Send the wireless signal of the mobile phone to receive the home router: Settings - Wi-Fi connection - Wireless LAN - Add (OK) The wifi signal is sent by the operator's AP base station Wifi, after turning on the wifi function of the mobile phone, there is an obvious prompt, wifi is a way to dial up the Internet, connect with a mobile phone, and charge for the mobile phone network card, regardless of the wireless router signal (wireless LAN) at home!

The phone can't connect to the Internet, and it has nothing to do with your host. You should look for the reason on the router.

Let's see if the router is powered on?..

If you can't do it, you can use the network cable that was originally connected to the computer case to connect the laptop. Then set it up again. What the host and router are one, this is said by people who don't understand computers at all.

The router and the computer are integrated, and you just want him to separate when you install the router, and just look for the broadband one to turn down the router from the new.

Is the phone module broken? I've had this problem too.

It's funny, this kind of problem doesn't happen.

1. It is best to enable the DHCP function on the router.

2. The wireless network card does not set the IP, and the pure spine is automatically obtained (router DHCP allocation). Otherwise, you can only set the address with the same IP segment as the router LAN.

3. Set up the encryption authentication function of the router wireless, select WEP if you are not clear, and set the password. When connecting to the Internet, just enter the password to do Wang infiltration.

At present, some routers use WPA PSK or WPA2 PSK authentication protocol, if your network card does not support it, it will not work. It's not a big problem to press 3 points, it's just not very safe.

Open IE browsing, enter, password and username should be adminThen you can set up your router and you're good to go.

The mobile phone can receive a wireless signal but cannot access the Internet, which proves that there is no problem with the router. Router issues. For example, the crystal head is bad, the cat is bad, and the broadband signal is abnormal.

The router is not set up, and the router is not automatically connected to the network. Set up your router again.

The router has to fill in your network username and password, as well as the gateway and the like, as well as your computer IP settings automatically best.

If you want to reset the router name, you can do it with the password or something, and you can use it, I have had this problem.

Unplug the router and check it again.

Restore factory settings, there is a problem with the general settings.

or restart the router (frozen).

Restart the route, not in the reconfiguration.

Can't you just use a wireless router, it's so troublesome, and there is a route with a route. Whether your computer is connected to a wired or wireless router. If the computer is connected to a wired connection, it is estimated that there is a problem with your wireless routing settings.

Don't bother typing, take a look at the setup here.

Are your two routers connected?,When the router is connected, you need to use the network cable of the crossed wire to connect.。 Open the next-level router settings interface, if the WAN shows a prompt such as not connected, then the network cable is not suitable, redo it, and the two routers cannot be set in the same network segment.

It is estimated that the DHCP function of your router is not turned on or the settings are incorrect, resulting in the phone not receiving the correct IP parameters.

The computer can be connected to wireless Internet access, but the mobile phone connection can not be connected to the Internet, reason:

1. The wireless name problem causes the mobile phone to not be able to access the Internet normally;

2. The mobile phone itself is set up in a problem, resulting in the inability to access the Internet normally;

3. Wireless router failure.

Solution: 1. Log in to the router, log in to the router (this case takes TP-Link as an example, the default address of the general router is, the username and password are admin, and the specific data can refer to the back of the router or the manual), find the [Wireless Settings] option on the left side, select [Basic Settings], enter the SSID number (wireless wifi name), it is recommended not to use Chinese characters, click [Save];

3. Change a router, re-dial the network and set the wireless wifi name, log in to the router, find the [Network Parameters] option on the left side, select [WAN port settings], enter the correct Internet account and password, set the connection method (the default is to connect on demand, change the automatic disconnection time to 0, or select automatic connection), and click [Save].

Your question is not very clear, and now there are three questions that need to be clarified, 1. What equipment is your landlord using for ADSL triage?

2. How is your wireless router connected and set up?

3. When the tenant does not use the router, whether to use broadband dial-up Internet access?

Only by understanding the above three points can we determine how to connect and set up routing!