Ford Edge new car exhaust smoke, imported Ford Edge engine black smoke what s going on

There are several situations of exhaust smoke:

1. If it is black smoke, it means that the mixture is too thick, which is a manifestation of insufficient combustion.

Several ways to solve the problem: clean the throttle, fuel injector, intake tract; Match the data of the driving computer; The gasoline added is not very pure, try adding a higher grade gasoline.

2. If it is white smoke: this means that there is a small amount of water in the cylinder, which becomes white gas and is discharged after combustion.

Cause of the problem and solution: It may be that the cylinder gasket between the engine cylinder head and the cylinder block is broken down (easy to break down at high temperatures), and the cylinder gasket can be replaced.

3. If it is blue smoke: this is the manifestation of burning engine oil, the cause of the problem and the solution: Generally, when the car is long or the number of kilometers is more than 100,000, there will be a situation, and the parts related to burning engine oil are generally

Valve seals, valve guides, cylinder liners, piston rings, pistons, etc., can be disassembled at the repair shop to check the damaged parts, and then replaced.

Tips: If you find light smoke around the engine cover when driving, it may be that the engine water temperature is too high, and the pot is boiling!! Here is a reminder that you need to pay more attention to the water temperature when driving in summer, if the water temperature is too high, it will accelerate wear and shorten the normal service life of the engine.

Hope it helps.

Is it blue smoke? Blue smoke is to burn engine oil.

There are two ways to solve the problem of burning engine oil

Overhaul. PNF restoratives.

Benefits of this one:In the case of overhaul, the cost is very high, the vehicle depreciates quickly, and the later run-in is also very troublesome. First of all, you need to find out the reason for your burning oil, oil circuit blockage, carbon deposits, piston ring stagnation can be repaired with PNF repair agent, there are many riders who have successfully repaired through PNF repair agent, you can refer to it.

Summary. This can be caused by insufficient engine oil or low transmission oil. It is recommended to check whether the grade and amount of engine oil and transmission oil are normal, and if not, change the engine oil as soon as possible to ensure the normal operation of the engine.

This can be caused by insufficient engine oil or low transmission oil. It is recommended to check whether the grade and amount of engine oil and transmission key oil Zhaoliang are normal, if not, change the engine oil as soon as possible to ensure the normal operation of the engine.

I can't hit the fire.

It's too cold, what's the matter with the black smoke that can't be emitted?

If the car does not start, it may be caused by a malfunction of the battery, internal components of the engine, gasoline supply, exhaust pipe, or other components. If the fault occurs, it is recommended that you immediately send the vehicle to a professional maintenance station for diagnosis, and handle it accordingly according to the maintenance suggestions to ensure the safe operation of the vehicle.

Summary. Dear, I'm glad to answer your <>

The Ford Edge will shake when it starts in the morning, and the engine needs to be dismantled with white smoke. To disassemble the head for inspection and maintenance, 2800 yuan of working hours. The result of Zui bad is to replace the head. <>

<> Ford Edge will shake when it starts in the morning, and the engine needs to be dismantled with white smoke.

Dear, very happy to answer for you<>

The Ford Edge will shake when it starts in the morning, and the engine needs to be dismantled with white smoke. To disassemble the head for inspection and maintenance, 2800 yuan of working hours to read the wheel celebration fee. The result of Zui bad is to replace the head. <>

Big Red Flower Tung Eyes] <>

Hello dear, extended content: General causes of engine shaking: engine lack of cylinder Engine lack of cylinder mainly refers to the engine missing chain has one or more cylinders that do not work normally, which is generally manifested as:

There is a significant intermittent exhaust gas flow from the car, and at the same time, the exhaust pipe shakes so badly that the engine can be clearly felt, sometimes accompanied by a sudden sound. This is mostly related to ignition coil failure. <>

Is it possible that the antifreeze is leaking?

The 4S shop said that the engine needed to be dismantled.

Kiss, it may be that the antifreeze is leaking. <>

Does that need to be dismantled for engine inspection? Does replacing the spark plug work.

Dear, the 4S shop is right to say that the Yuansheng Sparrow needs to disassemble the engine, because there is also an antifreeze orange early channel in the engine, and you are not the first owner of this situation. <>

Big saffron laughing limb].

Dear, you need to disassemble the engine for inspection, it is useless to replace the spark plug, and the white smoke is because the antifreeze is burned. <>

Okay, if that's the case, what will be replaced, and how much will it cost?

Kiss, if so, to replace the cylinder gasket, the cost is 150 yuan. Specific issues also need to be taken apart for inspection. There is a serious need to change the engine.

Dear, the engine ** is 15,000 yuan. <>

Due to processing and assembly errors, the frictional resistance of the moving parts of the new car is always much greater than normal when it starts to run, and the running-in (also known as walking) effect in the early stage of the car will have a great impact on the service life, working reliability and economy of the car. Therefore, the run-in regulations must be strictly implemented when using new cars.

1. Run-in regulations for new cars within 1000 kilometers:

1) Never drive at full speed.

2) - Generally not to drive at a speed of more than 100 km/h.

3) Avoid driving at high speeds in all gears.

2) The run-in of the vehicle between 1,000 and 15,000 km: it can be gradually increased to the maximum speed or at the maximum permissible speed of the engine.

2. After the run-in period, attention should be paid to:

1) When driving a car with a tachometer and shifting into the approaching high speed, the maximum engine speed allowed for a short time is 5 500 rpm when the pointer reaches the red indication zone at the latest. The maximum permissible speed in each gear is 40 kmh in the first gear, 65 kmh in the second gear, 100 kmh in the third gear, 135 km/h in the fourth gear, and 165 kmh in the fifth gear.

2) Avoid running the engine at unnecessarily high revs, and switch to high gear early to save fuel and reduce noise.

3) Do not drive the engine speed too low, and only change to low gear when the engine is working hard.

4) The speeds and rotational speeds listed in the instructions are only applicable to engines with normal temperatures. When driving cold, do not allow the engine to work at the highest revs, whether in neutral or in other gears.

5) New tires don't have optimal adhesion when they start with use, so new tires also need to be walked, slower for the first 100 km, and driven with care.

6) The new brake friction plate also needs to be run-in, in the first 200 kilometers of driving, there is not yet the ideal friction, if the braking effect is slightly worse at this stage, the pressure of the pedal can be appropriately increased. The same applies after each subsequent replacement of the brake pads.

7) Under possible conditions, the new car should avoid continuous driving for a long time during the run-in period, so as to avoid the engine and chassis parts continue to work for too long, resulting in the aggravation of the wear of the parts, and directly affect the service life of the car. Also avoid running at full load, generally in the first 1000 kilometers of driving, it is best to run below 80% of the rated load. Also, try to avoid driving at high speeds, and don't go faster than 70% of the top speed with the throttle open for the first 2,000 km/h.

8) during the run-in of the new car, the driver should heat up in situ after the new car starts at the beginning, and then start after the water temperature rises to the working temperature range, and should choose a good road surface during driving, and slow down when the road condition is poor; When driving, the throttle should be smaller, the operation should be light, once the engine or chassis sound is found to be abnormal, it should be stopped to check the fault in the embryonic period.