-
FAW-Volkswagen Lingdu door drain is located under the front machine cover, inside the engine compartment, between the gearbox and the battery, and the specific operation steps to find the FAW-Volkswagen Lingdu door drain are as follows
1. Open the driver's door of the FAW-Volkswagen Lingdu car.
2. Pull the hood switch on the left side of the driver's leg of the FAW-Volkswagen Lingdu.
3. Lift the engine hood of the FAW-Volkswagen Lingdu upward.
4. Use the support rod to support the engine hood of the FAW-Volkswagen Lingdu car, and ensure that the support is firm to avoid danger during operation.
5. The door drain of FAW-Volkswagen Lingdu is located under the front machine cover, inside the engine compartment, and between the gearbox and the battery.
-
Generally, the drainage holes of the vehicle are in the following parts: the front windshield of the engine compartment, the four corners of the sunroof, the lower part of the front and rear doors, the fuel tank cap, the bottom of the trunk spare tire, and the gap between the front and rear headlights and the body fender. One of the most likely areas for blockages is the drain holes in the engine compartment and sunroof.
Requirements for stamping positioning holes: the position and quantity of two stamping positioning holes for each part, the main and secondary two positioning holes, generally distributed in the diagonal direction of the sheet metal parts, there should be a certain distance, which is conducive to the positioning of the sheet metal parts in the stamping die; The two positioning holes should be distributed in a relatively flat area of the part, and the plane should be parallel. Due to stamping deformation, the positioning hole should not be too close to the edge of the sheet metal part.
Requirements for welding locating holes:
The position and quantity generally have two positioning holes in each part or welding assembly, and the primary and secondary positioning holes are distributed in the diagonal direction, and there should be a certain distance, which is conducive to the positioning of sheet metal parts in the welding fixture.
The two positioning holes are best distributed in the relatively flat area of the part, and the plane where they are located should be parallel, preferably parallel to the coordinate system of the whole vehicle; The positioning hole should not be too close to the edge of the part, the main positioning hole is a round hole, and the secondary positioning hole can be designed with a long round waist hole.
The above content reference: Encyclopedia - Leakage hole.
-
Lingdu ( Check price |.)The door drain is located under the front machine cover, inside the engine compartment, between the gearbox and the battery, and can be seen from under the front windshield. It does not need to be opened manually, and the drainage hole is originally open.
Generally, the drainage holes of new cars are blocked with tape or other things. After buying a new car, be sure to check the drain hole in the door in time to see if it has been opened. If you don't open the drain hole, it will easily cause water to accumulate in the door when it rains or washes the car, and it will rust over time.
According to the different locations of the displacement, the drain on the car can be divided into door drain, sunroof drain, air conditioning drain, oil slag hole drain and drain under the front windshield. Door drain opening, although the door glass is closely connected to the sealing strip, when it rains, more or less water will still flow into the door through the gap between the sealing strip and the glass. This water flowing into the door is drained through the drain in the lower part of the door.
When using the car in a daily life, you should often clean up the obvious leaves and debris near the drainage holes in the car. If the drainage hole is blocked, the water will be deposited in the door, and over time, it will cause rust and rot of the sheet metal in the door, and even if the water is too large at one time, it will also cause the water to flow out of the gap between the door inner panel and the door sheet metal and flow into the cab. You must pay attention to the small advertisements that are usually stuffed on the glass, so as not to let them fall into the door, as it is very easy to block the door drain hole after rotting.
Photo by Zhang Guiye) @2019
-
The Lingdu door drain is located under the front bonnet in the engine compartment, between the gearbox and the battery, which can be seen from under the front windshield. It does not need to be opened manually. The drain hole is always open.
Generally, the drainage holes of new cars are blocked with tape or other things. After buying a new car, be sure to check the drain hole in the door in time to see if it has been opened. If you don't open the drain hole, it is easy to cause water to accumulate in the door when it rains or washes the car, and it will rust over time.
According to the different distribution locations, the water outlets on the car can be divided into door outlets, sunroof outlets, air adjustable outlets, oil hole outlets and front windshield outlets. Door drainage, although the door glass is tightly connected to the sealing strip, when it rains, more or less water will flow into the door through the gap between the sealing strip and the glass. The stagnant water flowing into the door will be discharged through the outlet at the lower part of the door.
When using the car on a daily basis, it is necessary to frequently clean up the obvious leaves and debris near the drainage holes in the car. If the drain hole is blocked, stagnant water will be deposited inside the door, which will cause the metal plate inside the door to rust and rot over time. Even if too much water rolls at a time, the water will flow out of the gap between the inner door panel and the door sheet metal and flow into the cab.
Usually, small advertisements stuffed in glass must be careful not to let them fall into the door. After decay, it is easy to clog the door drain hole.
-
If you find that the antifreeze in the water tank of the water tank in the engine compartment is found to be lower than the minimum scale value (the normal value of antifreeze should be between max and min), it is necessary to add it in time, and the amount of addition depends on the specific lack of amount, otherwise it will affect the antifreeze performance of the engine.
Volkswagen Lingdu opens the engine compartment, and the antifreeze can be unscrewed and added, but be careful not to exceed the upper limit of the scale, and you can add water and antifreeze by opening the water tank cover. Generally, the water tank is inside the front face of the middle net.
Volkswagen Lingdu's water tank, also known as radiator, is the main part of the automotive cooling system; The function is to dissipate heat, the cooling water absorbs heat in the water jacket, dissipates the heat after flowing to the radiator, and then returns to the water jacket to circulate to achieve temperature regulation. It is an integral part of the engine of the car.
The water tank is an important part of the water-cooled engine, as an important component of the water-cooled engine heat dissipation circuit, it can absorb the heat of the cylinder block and prevent the engine from overheating due to the large specific heat capacity of the water, and the temperature increase after absorbing the heat of the cylinder is not very much, so the heat of the engine is called through the liquid circuit of the cooling water backup base, and the water is used as the heat carrier to conduct heat, and then the heat dissipation is dissipated in a convection mode through a large area of heat sink to maintain the appropriate working temperature of the engine.
1.Make sure the engine and radiator are cold and that the discharge at the bottom of the radiator is closed.
2.Check the owner's manual to determine the mixing ratio of antifreeze to water in the coolant and the appropriate dosage.
3.Place a funnel inside the radiator neck.
4.Carefully pour the recommended amount of antifreeze inside the radiator through the funnel and radiator neck.
5.Pour in water as needed for the mixing ratio.
6.Install a radiator cover, preferably a new one.
7.As recommended by the manufacturer, fill the ** container with coolant.
8.Run the engine, remove the air that has entered the coolant, and check the coolant level again.
Photo by the text: Pacific Automobile Network Q&A called the beast).
The Civic and Lingdu, as two A-class cars, are really very competitive models, and there are many consumers hovering between them. The Civic entered the Chinese market very early, has experienced the test of the market, and has many loyal fans. Lingdu is known as the most beautiful model of Volkswagen, and it is very eye-catching as soon as it is launched. >>>More
The original engine oil is generally fully synthetic or semi-synthetic, and the maintenance mileage is 5000 kilometers, and the fully synthetic engine oil can be used if it is extended, and the maintenance mileage is about 8000-10000, if you want to extend it, you need to use PAO level engine oil, like I am now using German GT Magic Red engine oil, which belongs to the real fully synthetic engine oil, and there is no problem with running 12000 normally, and it is a linear recession, not like the general engine oil has an obvious sense of decline, The power boost is also better than the average fully synthetic motor oil, and I am now in the fourth pot, and the power of the car has not decreased at all.