Royalstar Sanyo washing machine does not drain fault

Clause. First, first of all, start with the drain pipe of the Royalstar washing machine

1. Make sure that the Royalstar washing machine has been put down the drain pipe;

2. Check whether the drain pipe of Royalstar washing machine is deformed or twisted;

3. Make sure that the drain pipe of the Royalstar washing machine is unblocked, and there is no foreign object blocking the drain pipe. The above three points are all common causes of Royalstar washing machines that do not drain or drain slowly, and if these faults occur, they may be easily eliminated.

Clause. 2. After clearing the drainage fault caused by the above drainage pipes, if the Royalstar washing machine still does not drain, adjust the Royalstar washing machine program to single dehydration, and then start the Royalstar washing machine. If there is a sucking sound, it means that the circuit and drain solenoid are properly engaged.

Clause. Third, the next step should be to check whether the drain valve of the Royalstar washing machine is blocked; Determine whether the tension spring of the drain valve is falling off or whether it is rusted and broken, and if this happens, the damaged parts need to be cleaned and replaced. If there is no suction sound, the Royalstar washing machine may be faulty in the circuit, and the circuit failure is generally due to the failure of the circuit or electromagnet that controls the drainage switch.

If it does not fall off, use a multimeter to measure the resistance of the two terminals of the drain solenoid, if the resistance value is infinity or less than 30 ohms, it means that the drain solenoid has been broken or short-circuited, and should be replaced.

Clause. Fourth, if it still does not work normally after replacement, it may cause the failure of the program controller due to the burning of the drainage electromagnet (generally the thyristor that controls the drainage), and the controller needs to be overhauled. The reason why Royalstar washing machine does not drain is basically caused by the above faults, as long as you check them one by one, it is not difficult to discharge the fault.

Partnership. Hefei Royalstar.

Sanyo Electric Co., Ltd. is a company owned by the former Hefei Royalstar Group Co., Ltd. and Japan's Sanyo Electric Co., Ltd.

It is a Sino-Japanese joint venture established in 1994.

The company mainly produces washing machines, microwave ovens and core components and other products, and has a market share of washing machines and microwave ovens.

Both ranked third in the industry, first among international brands, and entered the first camp of China's home appliance industry. The construction of new refrigerators and household appliances is being stepped up. The company has been rated as "National Excellent Foreign-invested Enterprise".

China's Most Innovative Enterprise".

Partnership.

Hefei Royalstar Sanyo Electric Co., Ltd. is a Sino-Japanese joint venture jointly invested and established in 1994 by the former Hefei Royalstar Group Company and Japan's Sanyo Electric Co., Ltd.

The company mainly produces washing machines, microwave ovens and core components and other products, and the market share of washing machines and microwave ovens ranks third in the industry, the first place in international brands, and enters the first camp of China's home appliance industry. The construction of new refrigerators and household appliances is being stepped up. The company has been rated as "National Excellent Foreign-invested Enterprise" and "China's Most Innovative Enterprise".

Sanyo washing machine and Royalstar washing machine in China are one family.

Royalstar is a local brand in Hefei, Anhui Province, founded in 92 (estimated); In 94, a joint venture company was established with Sanyo of Japan called Royalstar Sanyo Electric Appliances, which produces Sanyo washing machines and does not produce any products of the Royalstar brand.

In the past nine years, the investment of Royalstar Group has failed, and the brand has been sold to Midea Group, and the Royalstar ice washing products in recent years are all produced by Midea.

It was not until the first half of 2014 that the Royalstar brand expired and returned to Royalstar Sanyo Electric Company, which began to produce and sell ice washing products under the Royalstar and Sanyo brands. (Royalstar Sanyo Electric Company also has a brand called Didu).

Hello dear <>, Royalstar Sanyo accompanies the automatic washing machine does not turn. The reasons are as follows: 1. If the motor has a humming sound, but does not rotate, it may be a problem with the starting capacitor. If there is no sound from the motor, it may be that the lid linkage switch of the dehydration bucket is faulty.

2. It may be that the belt is loose, or the mechanism piece on the drum cover is broken. 3. The automatic washing machine does not rotate, and some motors with clutches may be very hot, and the starting capacitor may be broken, or the wire head will fall off and the motor will not start. If there is no clutch, the reed may be stuck.

Pro-<>

Fresh loss and leaking flowers].

What to do if the washing machine does not drain water:

1. The washing machine is clogged

Check that the drain filter on the lower right side of the washing machine is not clogged with fluff and dirt, and if so, clean it up. Rotate the filter in a counterclockwise direction and gently pull it out, remove the fluff and dirt, wash it with water, and then put it in place and tighten it. Small pieces of clothing can enter between the inner and outer cylinders and press against the lower drain of the outer cylinder, which can also block the drain opening.

At this point, open the back cover of the washing machine, remove the heater or bellows, and remove the laundry with tweezers.

Second, the connection pipe problem

Check and clean the connecting pipe between the bellows and the drain filter, and remove the dirt in the connecting pipe between the filter and the washing machine drain pump and the drain pipeline to ensure that the drain pipe is unblocked. For washing machines with shaded displacement pumps, check whether the cooling fan of the drainage pump is blocked. Due to transportation or other reasons, the plastic cooling fan of the dewatering pump is likely to be entangled or blocked by debris, which prevents the fan from rotating and prevents the dewatering pump from rotating.

3. The wire falls off

Check whether the two wires of the washing machine drain pump have fallen off, and if the wires connected to the drain pump are intact, use a multimeter to measure the DC resistance of the drain pump. The dewatering pump is controlled by the two pairs of contacts -30 of the program controller, and the dewatering pump only works when both pairs of contacts are switched on at the same time.

Fourth, the drainage pump does not move

Due to improper use, coins, buttons and other objects fell into the chamber of the drainage pump, blocking the rotation of the impeller of the drainage pump and making it unable to drain water. Open the impeller chamber cover of the drain pump and remove the foreign object, and the fault can be eliminated.

Fifth, the drainage pump is damp

The drain pump is damp and rusty, causing the rotor to fail to rotate, resulting in the drain pump being unable to drain water. Remove the drain pump, remove the rust spots and add lubricant to eliminate the fault.

There are many reasons why Royalstar washing machine drain failure can occur, including the following situations:

1.Drain blockage: Drainage failure occurs when the drain mouth is blocked, causing water to not flow out. It is possible to check if the drain pipe is blocked.

2.Drain pump failure: The drain pump is responsible for pumping the water out of the washing machine, if the drain pump fails, the drain will not change or even fail to drain at all. You can check if the drain pump is working properly.

3.Drain cover problem: Some washing machines have a drain cover inside, and if the drain cover is not closed properly, it will cause the water to not drain out. You can check if the drain cover is closed properly.

4.Faulty water level sensor: If the water level sensor fails, the washing machine will not be able to detect the water level correctly and will not automatically enter the drain mode. You can check if the water level sensor is working properly.

There are many ways to solve the drainage fault of Royalstar washing machine, which is repaired according to the cause of the failure. For example, cleaning drain pipes, replacing drain pumps, reinstalling drain covers, repairing or replacing water level sensor coders, and more. It should be noted that caution must be exercised during the repair process to ensure safety and effectiveness.

If you really can't solve the problem by yourself, you can seek professional help or contact Royalstar customer service for repair.