Samsung washing machine to 8 minutes single spin dry does not work, what s wrong

Hello dear Samsung users:

The drum washing machine automatically stops without dehydration, and the time remains the same, only the inner drum runs at low speed, which is not a fault. The drum washing machine has high requirements for the balance of the clothes, and is equipped with an eccentric automatic protection function when designing, which can automatically detect the eccentricity of the washed clothes. When dehydrating, it is necessary to adjust the balance state of the clothes on both sides of the inner cylinder, there are few clothes, when adjusting, it is easy to turn to the side of the machine, and it is difficult to perceive the balance of the clothes on both sides of the inner cylinder, especially for washing a single piece of clothing with large water absorption, such as:

Cardigans, towel quilts, thick coats, curtains, etc. Therefore, it is necessary to adjust the balance of the garment by repeated rotation to reach a balanced state before it can be dehydrated normally.

It is recommended that you test the empty machine to see if the machine can run normally, if the empty machine is dehydrated normally, it means that there is no problem with the machine. If the empty machine is dehydrated and cannot work normally, it is recommended that you log on to Samsung's official website for repair.

The engineer will come to inspect and repair for you.

Samsung knows that we will provide you with high-quality solutions and answer your questions attentively, and hope to get your satisfactory evaluation.

Broken washing machine, blind design, not good at all.

The reason for this is that there are a lot of dehydrated clothes that are put into the washing machine at one time, and the clothes are offset unbalanced during dehydration. The washing machine automatically enters the self-balancing program (it looks like the washing machine is turning again, but the time remains the same).

1. If the dehydration before rinsing (starting after draining), it is not particularly serious clothing imbalance, and the dehydration bucket (including the dehydration outer barrel) will swing and collide with the safety switch due to the action of centrifugal force, and the washing machine will self-dehydrate to carry out the self-balancing procedure, that is, stop the dehydration and turn to water injection - wave wheel swing (balance clothes) - drainage - dehydration again.

2. If the balance requirements of dehydration of clothes are not met, the washing machine will automatically carry out several self-balancing procedures, and then buzz to inform and shut down (the set program cannot be carried out normally).

3. For automatic washing machines, the solution is to appropriately reduce the amount of laundry that can be rented by putting it into the washing machine for washing dehydrated clothes at one time.

If the Samsung washing machine is set to stay unchanged for 7 minutes, the first thing to do is to check whether the power supply is connected, check whether the plug is connected, check whether any buttons are pressed on the lifting board of the control surface, check whether the water level of the washing machine is normal, check whether the filter screen of the washing machine is blocked, and check whether the circuit of the washing machine is faulty.

Samsung washing machines are one of the most common household appliances in modern homes, and their diverse functions and ease of use have always been welcomed and trusted by consumers. However, during use, we may encounter some problems, such as the washing machine suddenly stopped moving at a certain time. Today, this article will take you through the causes of this problem and possible solutions.

When a Samsung washing machine is set to stay still for 7 minutes, this situation is most likely caused by a faulty power supply and circuit. Maybe the power outlet is not plugged in properly, or the power supply voltage is unstable, which can cause the washing machine to not work properly. In addition, if there is a problem with the circuit of the washing machine, it is also easy to cause such problems.

For example, a damaged circuit board or other malfunction can affect the normal operation of the washing machine.

So, how do you fix it? First of all, we can check if the power outlet is plugged in correctly, try to replace the power outlet or power cord, and see if that solves the problem. If it still can't be solved, you need to consider the problem of slag circuit.

At this time, we can unplug the power cord of the washing machine, wait about 10 minutes, and then plug it back in. This can try restarting the washing machine, which may solve the problem. If the heading problem persists, you need to contact a professional maintenance personnel for repair.

In short, when the Samsung washing machine is set to stay unchanged for 7 minutes, we don't have to be too nervous, and we don't need to disassemble and repair it ourselves, but patiently investigate and solve it. If the problem is more serious, it is best to call in a professional to repair it to avoid more serious consequences. In addition, in the usual use process, we should also pay attention to the care and maintenance of the washing and sailing machine to avoid problems and ensure its normal service life.

If your Samsung washing machine is scheduled to stop after 7 minutes, it may be due to a malfunction. You can try to follow the next steps to exclude:

1.Check if the washing machine has a power source**. If there is no power supply, you can try to check the plug and power cord for damage, or check for leaks in the circuit to clear up the fault.

2.Check that the washing machine has enough water**. If the water pressure is insufficient or the faucet is not turned on, the washing machine may not be working properly.

3.Check that the door lock of the washing machine is working properly. If the door lock is not locked before returning to the forest, the washing machine may not start.

The Samsung washing machine is set to stay unchanged for 7 minutes, that is, there is a problem with the dehydration link, which may be that the clothes are biased.

Samsung Drum Washing and Washing Half of the Clothes Machine Will Stop Working by Itself 1, the control circuit board of the washing machine is faulty, check the circuit board, and replace the circuit board if it does not work. 2. It may be the fault caused by the wet or water ingress of the control circuit board, replace the circuit board. 3. It may be that the power supply line is faulty or the program controller is faulty, and the fault can be removed by replacing the power fuse and capacitor.

4. Please ask professional maintenance personnel to provide door-to-door service.

Summary. Hello, there are three main situations when the drum washing machine works and automatically stops:

1.The remaining time is displayed, the inner cylinder does not work and there is no action sound, and the machine can continue to work by pressing the start button.

Cause of failure: imbalance of underwear.

2.Displays faults**, e.g. 4e 5e

Cause of failure: no water inlet No drainage, it is recommended to clean the inlet valve filter screen and residue filter, the specific operation method can refer to the manual.

3.The remaining time is displayed, the inner cylinder does not work but the drain pump has an action sound, and the machine can continue to work by pressing the start button.

Cause of failure: too much laundry detergent, the machine itself carries out a defoaming program, and the next time you use less detergent, you can avoid it.

Samsung's fully automatic washing machine stopped working after 17 minutes.

Hello dear. I'm Mentor Jinx, and I'm happy to serve you Zen Sen. Your problem has been received, and it is being solved for you, and the number of people who have been consulted by the limb is currently decreasing, and you will be able to wait a little longer in about 3 minutes

Hello, there are three main situations in which the drum washing machine works automatically and disturbs the shutdown: 1The remaining time is displayed, the inner cylinder is not working and there is no action sound, and the machine can continue to work by pressing the start button.

The cause of the failure of God: the imbalance of the inner clothes. 2.

Display fault**, such as 4e 5e fault reason: no water inlet no drainage, it is recommended to clean the inlet valve filter screen and residue filter, the specific operation method can refer to the manual. 3.

The remaining time is displayed, the inner cylinder does not work but the drain pump has an action sound, and the machine can continue to work by pressing the start button. Cause of failure: too much laundry detergent, the machine itself carries out a defoaming program, and the next time you use less detergent, you can avoid it.

If my answer is helpful to you, please click to end the consultation, please give a thumbs up (in the lower left corner of the filial piety evaluation), looking forward to your praise Your efforts are very important to me, and your support is also the motivation for my progress and celebration. If you feel that my answer is still satisfactory, you can click on my avatar for one-on-one consultation. Finally, once again, I wish you good health and a good mood!

Hello, the Samsung washing machine washes clothes normally but doesn't dry out, what's the matter? The washing machine is not dehydrated.

1. Unbalanced clothes: When the washing cannot be adjusted to balance, the washing machine will automatically set a low speed, and the dehydration effect will be slightly worse at this speed. The washing machine does not dehydrate.

Second, the switch of the top cover is damaged, and the washing machine is not allowed to open the top cover because it is a high-speed action when dehydrating, so there is a linkage switch on the top cover, which will be automatically disconnected as soon as the cover circuit is opened. If it is damaged and dehydrated, it will not move! The washing machine is not dehydrated.

3. Clothing texture: high-speed dehydration is recommended for washing products with strong water absorption performance (high-speed dehydration cannot be used for some high-end clothes). The washing machine is not dehydrated.

Fourth, the drainage system is blocked. The washing liquid in the water cylinder can not be discharged, or there is too much foam in the water cylinder, the washing liquid in the cylinder is difficult to drain for a while, the water level switch can not be reset, and the washing machine can not enter the dehydration program. The washing machine is not dehydrated.

5. The water level switch cannot be reset. The washing machine dehydration process starts with the water level switch reset after the washing liquid has been drained. If the drain level switch is damaged, dewatering is a procedure that needs to be carried out after draining, and if the water level switch is damaged, the dewatering procedure will not be entered.

Hello dear, it's a pleasure to serve you: the Samsung washing machine is no longer working after 1 minute of running; 1. In order to perceive the weight of the clothes, the washing machine will perceive the difficulty of rotation through the rotation of a small radian, and the signal fed back to the computer board by the large current of the motor is strong, and the water level required by the washing machine is set by the perceived weight of the clothes, and the washing machine will stop rotating and then start to enter the water. 2. The washing machine has started the soaking program, and the washing machine will generally turn a few times (to soak the clothes) and stop for a period of time when the washing machine is immersed in the section, and then start to turn again, then stop again, and turn the closed combustion to stop.

When it comes to the washing program or the spinning program, there is no problem with the washing machine, which is normal. 3. If it is not for the above two reasons, the drain pipe of the washing machine is leaking. Because the drain pipe is connected to the floor drain, you won't know when the water leaks, but when the water level drops, the washing machine stops and automatically replenishes the water, and when the water level reaches the set level, it will continue to operate, but it will not be affected in any way when the water level is dehydrated.

4. If the Samsung car washing machine does not turn for a minute at the beginning, and then does not turn, the main engine of the washing machine is broken, and you need to find a professional after-sales maintenance personnel of Guangzhou Samsung washing machine for repair. Thank you for your patience, the answer has been found for you, please check it Oh I hope it can help you, I wish you a happy life.

Summary. 3. The drain valve does not open the clutch conversion, and the washing and dewatering of the automatic and automatic washing machine are completed by the gear at the bottom of the solenoid valve conversion, and the damage of the solenoid valve will also make the dehydration unable to operate normally. 4. Poor motor performance and capacitor problems, resulting in insufficient output power, can be solved by replacing the capacitor 5. The tightening screws of the inner barrel of the washing machine are loose, or the bottom bracket of the inner barrel of the washing machine is damaged.

If this is the case, in most cases, an empty washing machine can be dehydrated. 6. The washing and dehydration of the automatic automatic washing machine is completed by the gear at the bottom of the solenoid valve conversion, and the damage of the solenoid valve will also make the dehydration unable to operate normally, remember to collect this site.

The Samsung washing machine was washed and dried with 1 hour and 5 minutes left each time, and it stopped without drying.

There are several reasons why kissing can lead to this.

1. The washing machine panel door is not closed well or the switch of the top cover is damaged, it may also be that the switch is in poor contact, and the washing machine is not allowed to open the top cover because it is a high-speed action when the washing machine is dehydrated, so there is a linkage switch on the top cover, which will be automatically disconnected as soon as the cover circuit is opened. If it is damaged and dehydrated, it will not move!

2. The drainage system of the washing machine is blocked or the drain valve is broken, the washing liquid in the water cylinder can be discharged without staring at the mu before it is filled or there is too much foam in the water cylinder, the washing liquid in the cylinder is difficult to drain for a while, the water level switch cannot be reset, and the washing machine cannot enter the dehydration program. The Samsung washing machine will be washed until 12 minutes) The Samsung washing machine will be washed to.

3. The drain valve does not open the clutch conversion, and the washing and dewatering of the automatic and automatic washing machine are completed by the gear at the bottom of the solenoid valve conversion, and the damage of the solenoid valve will also make the dehydration unable to operate normally. 4. The motor performance is poor, the lead capacitance problem leads to insufficient output power, and the replacement of the capacitor can be solved 5. The tightening screws of the inner barrel of the washing machine are loose, the hall is rotten or the bottom bracket of the inner barrel of the washing machine is damaged. If this is the case, in most cases, an empty washing machine can be dehydrated.

6. The washing and dehydration of the automatic washing machine is completed by the gear at the bottom of the solenoid valve, and the leakage damage of the solenoid valve will also make the dehydration unable to operate normally, remember to collect this site.

Summary. Hello dear, the Samsung washing machine will automatically stop when it is in use, there are two situations: first, after the set laundry program is over, it will automatically stop and turn off the power; Second, because there are a lot of clothes that are put into the washing machine for washing and dehydration at one time, the clothes are seriously unbalanced when the dehydration starts at the end of drainage, and when the spinning bucket starts to rotate, the outer cylinder of the washing machine will directly touch the safety interlock switch, causing the washing machine to stop working; If it is not particularly serious clothing imbalance, in the process of high-speed rotation of the dehydration bucket, due to the action of centrifugal force, the dehydration bucket (including the dehydration outer bucket) will swing and collide with the safety switch, at this time, the washing machine will automatically carry out the self-balancing program, that is, stop dehydration, transfer to water injection - wave wheel swing (balance clothes) - drainage - dehydration again; If the laundry dehydration balance requirement is not met, the washing machine will automatically perform several self-balancing programs, then beep to inform and shut down (the set program does not work properly).

The Samsung washing machine stops washing until 43 minutes, and it doesn't stop if you don't put clothes.

Hello dear, the Samsung washing machine will automatically stop when it is in use, there are two situations: first, after the set laundry program is over, it will automatically stop and turn off the power; Second, because there are too many clothes that are put into the washing machine for washing and dehydration at one time, the clothes are seriously unbalanced when the dehydration starts at the end of drainage, and when the dehydration bucket starts to rotate, the outer cylinder of the washing machine will directly touch the safety interlocking slag switch, causing the washing machine to stop working; If it is not particularly serious clothing imbalance, in the process of high-speed rotation of the dehydration bucket, due to the action of centrifugal force, the dehydration bucket (including the dehydration outer bucket) will swing and collide with the safety switch, at this time, the washing machine will automatically carry out the self-balancing program, that is, stop dehydration, transfer to water injection - wave wheel swing (balance clothes) - drainage - dehydration again; If the balance requirement of dehydration is not reached, the washing and balancing machine will automatically perform several self-balancing procedures, and then beep to inform and pat the shutdown (the set program cannot be carried out normally).

For the second case, the solution is to reduce the number of relatives and put it in the washing machine to wash the dehydrated clothes at a time. I hope my Hui Zheng Zai Bi Ta can help you!