How to stick stickers on wooden cabinets, how to get rid of stickers stuck to cabinets

Remove the door panel and handle, and attach the sticker to both sides of the bookcase and the door panel, a total of three sides, please start from one side.

When pasting, use a scraper to squeeze out the air between the sticker and the wooden cabinet to make it flat.

After attaching the three sides, carefully cut off the sticker in the middle with a utility knife on the door frame side.

Attach the sticker to the top of the wooden cabinet and cut off any excess stickers around the edges.

Attach the cut sticker to the door panel, paying attention to whether the pattern is connected to the pattern on the edge of the door frame.

Finally, the door panel is put back on, and the stylish wooden cabinet is completed!

To prepare the furniture ready to be renovated, the stickers are ready, if the furniture is directly on the surface of the paint before, to scrape off all the paint, when scraping, be careful, try not to hurt the surface of the furniture.

Once all the paint has been removed, rinse the furniture with water, let it dry naturally, and wipe the dust off the table with a clean cloth.

Of course, it is easier to paste stickers, mainly because the preliminary work must be done well, and the choice of stickers must be consistent with the style of the furniture. Before the sticker renovation process, it is best to repaint the furniture for protection.

If you are self-adhesive, you can tear off the paper behind it and paste it directly, and if you are not self-adhesive, you have to buy glue to paste it.

1. Soak in hot water for a while, and then you can remove it.

2. Use a hair dryer to blow the glue and bake it hot.

3. Wipe it with wind oil essence, and it will fall off after a while, try it.

4. You can try the eraser. But at the beginning, you may feel that the more you rub, the dirtier it gets, but if you wipe it for a longer time, you will see the effect.

5. Soak it in water, put a little dish soap, and then brush it with an old toothbrush.

6. It is also OK to wipe it with a cloth dipped in alcohol or a second pot head.

Material preparation: a large piece of cabinet sticker, a paper cutter, and a rag.

1. First of all, take a large sticker, remove the plastic film under the sticker, and leak out the sticky finger surface of the sticker.

2. Place the adhesive side down and lay it flat on the flat surface of the cabinet. Then start from one side of the cabinet and slowly and firmly til it to bond the adhesive surface of the sticker to the cabinet.

3. After bonding, if there is a place that is not too peaceful, use a small scraper or cardboard shell given by the manufacturer to slowly scrape the uneven place.

4. Cut off the excess part of the sticker with a paper cutter.

5. Finally, wipe the surface of the cabinet with a clean rag. Potato source.

After the above 5 steps, the sticker is ready.

Note: The area of the sticker should be slightly larger than the surface of the cabinet, and the surface of the cabinet cannot be completely covered by the province.

The practice of stickers on the board: the surface of the board is treated, both to fill the gaps, cavities, etc., it is best to scrape off the putty, to dry and polish the ash, and then brush the white glue, to dry a little after the wood grain paper, the best wood grain paper brush glue can improve the firmness of the post, and then use an electric iron to iron the surface and then polish.

It should be noted that a layer of adhesive substances such as glue is applied on the board and paper, wait for the glue to dry naturally to 30%, and then fit, if it is a painted surface, you have to wipe it with alcohol or squeeze some with hand cream on it, and slowly rub it with your thumb will not hurt the painted surface of the furniture, if it is a tile surface, you can use toilet paper to dip it in water or nail polish polish remover, if you directly batch putty on the board, and then paste wallpaper, it will definitely fall off. The correct way is to brush the varnish on the surface of the wooden board, and then use the wallpaper glue to paste the wallpaper, first treat the surface of the wooden board, fill the gaps, holes, etc., it is best to scrape off the putty, to dry and polish the ash, you can brush the white glue, and paste the wood grain paper after the white glue is slightly dry, the best wood grain paper is also brushed with glue to improve the firmness of the post, and then use an electric iron to iron the surface and then polish it.

Thinner of the Bauhinia brand.

Shops that sell paint sell it.

It is possible to buy the smallest cans.

Ordinary glue can be dissolved.

Do not hurt wood, tiles, if the cabinet is made of plastic.

It needs to be used with care.

Rubbing too much may stain the plastic surface.

But it won't dissolve the plastic.

Just take a piece of cloth and wipe it.

How to remove stickers from cabinets:

1.The eraser can be removed by rubbing it slowly.

2.Use the hand wash solution, apply it to the glue stain, do not add water, slowly rub it repeatedly with your hands, slowly the glue stain will dissolve, wipe off the foam with a dry cloth, and then apply and rub it a few times to completely remove. You can tear it off by blowing it hot with an electric wind.

3.Wind oil essence. Apply a little and wait for two minutes to easily remove it by hand.

4.You can tear off a layer of paper on the sticker, then apply alcohol or gasoline, and then rub it back and forth on the surface with your hands, and finally wipe it off with a cloth.

5.Nail polish and hand cream can be applied to stickers to dilute and dissolve those non-sticky adhesives.

Hair dryer method: Use a hair dryer to blow the glue hot, and then slowly tear off the sticker. Wind Oil Essence Method:

Apply wind oil essence to the sticker and let it stand for a while, then tear off the sticker. Eraser method: Use an eraser to slowly wipe the stickers on the cabinet, at first it may get dirtier and dirtier, but after wiping for a long time, the stickers will slowly be wiped off.

Dish soap method: Fill a basin with water, then pour in dish soap and stir to foam, then use an old toothbrush to stick to the dish soap water to brush off. <

1. Hair dryer method: blow with a hair dryer, bake the glue hot, and then slowly tear off the sticker.

2. Wind oil essence method: Use wind oil essence to apply to the sticker and let it stand for a period of time, and then tear off the sticker.

3. Eraser method: Use an eraser to slowly wipe the stickers on the cabinet, at first it may become more and more dirty, but after wiping for a long time, the stickers will be slowly wiped off.

4. Detergent method: fill a basin with water, then pour in dish soap and stir to foam, and then use an old toothbrush to stick to the dish soap water to brush off.

Use tools scissors, paper cutting blades, dry towels, scrapers

The function of the dry towel is the same as that of the scraper, in order to flatten the sticker without leaving air bubbles. But it's easy to scratch the wallpaper with a scraper alone! And it will hurt with my hands for a while, and when I pasted it, I took it up and rolled it up slowly from the middle to both sides, basically sticking it relatively flat.

I don't have a concave and convex pattern on the cabinet door, which is still easy to paste, but the area is too large so it takes a long time.

Wipe the surface of the furniture you want to stick to!

Step 1) First of all, start with a large area, measure the size according to the width of the cabinet door and the thickness of the cabinet door, and calculate a few centimeters more to leave some leeway.

2) Take the thickness of my cabinet door about 2cm as an example, when pasting, first fold about 3cm vertically based on the side with the cabinet door hinge z (there is a lattice at the back, 1cm per grid), and the upper and lower sides can be left a little more so that they can be folded to the back and pasted.

3) After the top and the page are folded, tear off the sticker at the back Align the line of the top and the page to the cabinet door, and slowly remove the paper behind it from top to bottom, and wipe it flat with a dry towel while peeling it off. The bubbles are relatively large, you can slowly lift them up and re-level them with a towel (take them off to pull both sides up), and pay attention to the alignment of the folded lines. Be patient, be patient, be patient!

Say the important thing three times!

4) Stick the hinge along the corner of the side, the extra part is cut off with a blade, and the other three sides are pasted, and the extra part is folded inside.

After pasting the cabinet door, cut it according to the width of the seam between the cabinet door and the cabinet door, and stick it one by one, even if the paste is not so good. If you don't stick it, cut it a little more and stick it, and you can't see the seams if you don't look carefully.

You're talking about Boeing soft film, it's better to stick it when you make a cabinet. This will not peel. Sand the layout with sandpaper, wipe it clean, and remember to use a towel when pasting.