The gas stove keeps clattering, but what s the matter if there is no fire?

Cause 1: The battery is too low

The gas stove has a clattering sound and does not catch fire, which may be caused by the low battery. You will need to replace the battery and try to light it again in the future.

Reason 2: Dirt on the stove head of the gas stove

If the gas stove has been used for a long time and has not been cleaned, then the stove will produce dirt, and even block the gap (or a few small holes) sprayed to the ignition, and when the fire is lit, the gas cannot be effectively sprayed at the ignition place, although there is a clatter sound but there is no fire, which is a normal phenomenon.

Reason 3: Poor switch contact

When the gas stove has a clattering sound and does not fire, we should also pay attention to whether the shrapnel switch under the handle of the lighter is not in good contact. In the gas furnace that has been used for many years, the oil stain has penetrated into the switch shrapnel of the battery inside the igniter, resulting in poor contact, which is similar to a phenomenon of insufficient battery.

Reason 4: Clogged pipes

If there is a blockage in the gas pipeline, it is time to check the outlet valve. If the gas stove does not catch fire and you can still smell the gas, the gas pipe is blocked.

No powerIn the case of determining whether the gas stove has gas, whether the spark is weak when igniting, and whether the ignition sound is weak and weak, and the discharge frequency becomes obviously slow, in this case, the battery is usually dead, and the new battery can be replaced. Another possibility is that the battery is in poor contact.

Ignition needle and flame-out protection needle are dirty: Check whether the ignition needle or flame-out protection needle is covered by dirt, which will affect the ignition. If you have one, wipe it clean with a dry towel.

Precautions for gas stoves.

1. When stewing vegetables or making soup, some people like to turn the flame very small, which is also easy to cause air leakage or incomplete combustion. Therefore, when the gas stove is in use, the fire should not be turned on too small.

2. When using, you should always pay attention to the color of the stove. An orange flame indicates that the gas is not fully burned, in which case carbon monoxide is released. The flame can be adjusted by adjusting the damper under the cooktop, whichever is the blue flame.

First, the stove has been lit all the time.

First of all, see if the gas valve of the stove is open, if it is opened, then see if the battery of the stove is still charged, if the battery is used up, replace the No. 1 battery in time; If the circuit of the stove is not in good contact, there will also be a phenomenon that it cannot be ignited, at this time, the rust needs to be removed, and then the line is reconnected; If the ignition needle is not cleaned in time after a long time, it will also be easy to be contaminated with oil, resulting in the sound of ignition, at this time, as long as you use a cotton swab to clean the oil scale of the ignition needle, and then try to ignite. Regular home maintenance, just find a woodpecker for free** repair.

Summary. Reason 2: If the gas stove has been used for a long time and has not been cleaned, then the stove will produce dirt, and even block the gap (or a few small holes) that spray to the ignition.

The gas stove keeps clattering, but what is the reason why there is no fire?

The reply time period is filial piety: 10 a.m. - 1 a.m. In order to ensure the quality of our service, please do not send questions and inquiries during other time periods

The gas stove keeps clattering, but the reason why there is no fire is as follows:

Reason 1: The power is too low, and the gas stove does not catch fire, which may be caused by the low power. You will need to replace the battery and try to light it again in the future.

Reason 2: If the gas stove has been used for a long time, and it has not been cleaned, then the stove will produce dirt, and even plug the gap that sprays to the ignition (or a few small holes to make a bridge), when ignition, the gas can not be effectively sprayed on the ignition, although there is a clattering sound but no fire, this is a normal phenomenon.

Reason 3: Poor contact of the switchWhen the gas stove has a clattering sound and no fire, we should also turn off and roughly note whether the shrapnel switch under the handle of the lighter is in poor contact. In the gas furnace that has been used for many years, the oil stain penetrates into the ignition to turn on the battery inside the shrapnel, causing poor contact, which makes the phenomenon like a lack of battery.

Reason 4: Pipeline blockageIf the gas pipeline is blocked, it is necessary to check the gas outlet valve at this time. If the gas stove is rattling and the gas is not on fire, and you can still smell the gas, the gas pipe is blocked. Swim to take it.

1. Whether the battery has electricity.

In the case of determining whether the gas stove has gas, whether the spark is weak when igniting, and whether the ignition sound is weak and weak, and the discharge frequency becomes obviously slow, in this case, the battery is usually dead, and the new battery can be replaced. Another possibility is that the battery is in poor contact.

2. Ignition needle.

There is dirt in the flame-out protection needle.

Check whether the ignition needle or flame-out protection needle is covered with dirt, which may affect the ignition. If you have one, wipe it clean with a dry towel.

3. The nozzle is blocked.

If both of the above conditions are fine, you can check whether the nozzle is blocked. If there is, take out the fire cover first, and then use a thin iron wire to pass through the nozzle hole on the fire cover.

4. The ignition needle is not properly positioned.

Usually the distance between the fire needle and the fire bracket is about 4mm, and it should be aimed at the fire hole, so that the fire can be ignited.

5. The damper is adjusted too much.

If the damper of the gas stove valve body is adjusted too large, it is easy to cause the air flow from the fire hole to be too large, which will affect the electric spark. In addition, the air pressure is too high, and the high-voltage line.

The aging and damage of the microswitch will also cause the gas stove to not catch fire, and it is recommended to ask a professional to solve these problems.

Summary. 1.If the battery is not charged enough, it will make a slight noise when it is ignited, and the speed of discharge will be lower than normal. If that's the case, you'll need to get a new battery and then light it again.

The gas stove keeps clattering, but what's the matter if there is no fire?

1.The power of the battery is not enough, there will be a slight noise when ignition, and the speed cavity of the discharge will be lower than normal. If that's the case, you'll need to replace it with a new battery and light it again.

2.If the ignition makes a sound, but there is no fire, it may be that the gas pipe is blocked. It is necessary to check whether the tube has been bent and then flatten the tube.

If the fire hole of the furnace mouth or fire lid is blocked, and the gas cannot escape, the tomato cannot be ignited. The lid must be removed, cleaned with a thin wire or toothpick, and then re-lit.

Ignition with a lighter is still on fire normally.

3.There is a problem with the flame-out setting, the gas furnace has a temperature detection device, and the flame on the stove will burn stably only after the flame nozzle reaches a certain temperature roundness. In this case, it only needs to be lit with a lid and it will catch fire in a few seconds.

You can try changing the battery on your gas stove.

Also, pro. Note: When using the gas stove, ensure ventilation, there should be a window in the kitchen, which can be directly led to the outside, and the height of the kitchen should not be staring at the rice.

Avoid flammable things. Many people like to place food near the gas stove and place food bags near the gas stove at will, which is very dangerous. Refractory materials should be used around the gas stove, and flammable materials should not be piled up nearby.

Always check the air for leaks. Pay special attention to whether there is any air leakage on the gas stove. The most prone areas for gas leaks are:

Gas meter shell, gas pipeline connection points, valve, hose, etc. When the gas leaks to the extremities and to a certain extent, a violent ** is produced.

Ignition needle, no fire, no ignition.

How to adjust the ignition setting.

I am a double stove, the left side is not good, the right side is good, the ignition sound on the left side is also small, there is no fire.

Do you remember how much you would replace the new battery?

Changed. I've read yours on the Internet, can you tell me to be specific and don't let me spend money in vain.

The gas stove has changed to tease one side can not catch fire may be the chain source of the connection, the left is in front, the left is not open to the right is out of gas, the right can not be ignited may be the commonly used ignition needle and the corresponding stove is dirty, the ignition of the spark jumped off or due to dirty leakage caused by the ignition operation of the spark no spark, clean and wipe the dirt around the stove and the ignition needle, pay attention to the ignition needle connection to be firm, and then try to re-ignite the fire to sell fire.

It is also possible that the ignition needle is not in the right position, adjust the distance between the ignition base hole needle and the fire cover by 4-6mm, and align the fire hole well, because too close and too far may cause the ignition not to ignite, and it is best to ask a professional maintenance person to repair it.

Also, you can adjust the gas stove damper.

If it still can't be done, you need to consider that the micro switch may be damaged or the solenoid valve may be damaged, and ask an expert to replace it.

Hello, dear, I am happy to answer for you, according to the inquiry, the gas stove has not been lit and the cause and solution have been clattering: 1One situation is that the gas stove electric ignition is always non-stop, and the electronic ignition is broken.

2.In the second case, the coke on the surface of the gas stove was not cleaned in time. 3.

The three cases are that the switch button is not reset in time, and the battery can be replaced. 4. The four situations should be short circuits, and professionals should repair them. Please first check whether the white point needle has sparks, if there is no sparks, it means that the discharge needle is leaked and replaced, if there is a spark, it means that the discharge is normal, but the sparks are weak and can not be pointed.

The solution is to adjust the discharge needle backwards, that is, away from the stove, and see if the central fire is not oxygen-sufficient, and adjust the damper from the stove. It's good to adjust the damper in the place where Haida Wuyin is high. 5.There is also a situation where the lighter switch is flooded, you can take off the battery and install it after a few hours of drying!

Summary. The first reason is that the voltage of the gas stove battery is insufficient and it keeps ringing, and the battery can be replaced with a new one; <>

The gas stove keeps clattering, but what's the matter if there is no fire?

Hello dear, I am inquiring about you about the matter, please wait a minute<>

Dear, I found the following reasons for your inquiry.

The first reason is that the voltage of the gas stove battery is insufficient and it keeps ringing, and the battery can be replaced with a new one; <>

The second reason is that the gas stove has dirt on the empty stove, and after the gas stove is used for a long time, its stove will produce some dirty dirt, <>

It will block the outlet that sprays to the ignition, so when the fire is lit, the ventilation will not penetrate the fingers and can spray to the place where the ignition is ignited, and it can be cleaned and blinded and dredged without sound. <>

When the gas stove has a clattering sound and does not catch fire, we should also pay attention to whether the shrapnel switch under the handle of the lighter is not in contact with the good things. In the gas furnace that has been used for many years, the oil stain penetrates into the liquid sheet of the switch chamber of the battery inside the igniter, resulting in poor contact, which is similar to the <> of insufficient battery

When the gas stove has a clattering sound and does not catch fire, we should also pay attention to whether the shrapnel switch under the handle of the lighter is not in contact with the good things. In the gas furnace that has been used for many years, the oil stain penetrates into the liquid sheet of the switch chamber of the battery inside the igniter, resulting in poor contact, which is similar to the <> of insufficient battery

I hope mine is helpful to you.

<> have a great day<>

Thank you! How to solve the poor contact of the shrapnel switch under the handle?

Dear, the switch is in poor contact, it is easy to leak, you need to replace it in time.

<> it's dangerous.

<>Oh, thanks! You're welcome yo <>

Dear, I'm glad to answer for you! 1. The gas stove does not catch fire but there is a clicking sound, which may also be caused by the valve in front of the stove not being opened. 2. It is also possible that the high-voltage output wire is broken down or cracked, resulting in leakage, and then it cannot catch fire, and the fault can be eliminated by replacing the new wire.

3. If there is too much fouling in the electrode needle, the discharge will be weak, and it may also cause ignition failure. In daily life, the gas stove should be cleaned frequently and the electrode needle should be kept clean. 4. If the gas stove does not catch fire but there is a sound of clicking, it may be caused by the improper distance between the electrode needle and the ignition bracket, and the discharge is weak or not discharged, and the distance should be adjusted to 3-4mm.