After the washing machine is turned off, it will automatically power on again

Forehead. Well, this one. It is estimated that the button of the washing machine may be soaked in water! This causes the switch to be in an abnormal state of long-term semi-conduction. In this way, the washing machine will not turn on abnormally.

It is recommended that the panel be taken apart and used for a hair dryer.

Blow dry carefully--- preferably on the balcony, so that the moisture can be fully dissipated!

It's actually very easy to disassemble the washing machine. Any man can do it. Just remove a few screws on the side.

Well. There are several other possibilities:

Check the order, hehe, remember, I'll tell you the common ones to try.

First, the water pressure is low or the filter screen at the water inlet is blocked, which is manifested as the water inlet is very slow, and the eye can see that the specified water level has not reached the specified water level for more than eight minutes, showing E4

Second, the drain is blocked, and the drain pipe can be taken out to see it, and E1 will be displayed after the specified time

Thirdly, the upper cover switch is in poor contact and displays E2

Fourth, the clothing is biased, and the number of repeated corrections exceeds the specified display e3

Fifth, the water level sensor is damp, heavy dampness shows E6, and light dampness shows no water when booted? Commonly used? The program time does not display two horizontal lines to display the time directly, the low water level may judge that there is water to start directly, when the water is drained, it is thought that the water will continue to drain without draining, and the dehydration will not be started.

If none of the above is true, I'm sorry to tell you, it's better to find a professional master to repair it.

Good luck!

1. If the computer board that controls the forward and reverse rotation fails, replace the computer board. 2. If the clutch fails to perform forward and reverse rotation, replace the clutch. The fully automatic washing machine is controlled by the water level switch and the electromagnetic water inlet valve to control the water intake, drainage and motor on/off

So as to achieve automatic control. The solenoid water inlet valve plays the role of turning on and off the water source. When the electromagnetic coil is powered off, the moving core is tightly pressed against the rubber diaphragm under the action of gravity and spring force, and the central hole of the diaphragm is blocked, so that the valve is closed and the water flow is blocked.

When the solenoid coil is energized, the moving core moves up under the magnetic force, leaves the diaphragm, and makes the center hole of the diaphragm open, so that the water above the diaphragm flows into the laundry bucket through the center hole. Since the flow capacity of the central hole is greater than that of the holes on both sides of the diaphragm, the pressure above the diaphragm decreases rapidly, and the diaphragm will move up under the action of pressure difference, close the door and open it, and the water flow will be conducted.

Hello, this may be caused by aging, after all, it can be turned on normally and the circuit is not too problematic, and the automatic shutdown occurs halfway, it may be that the temperature is too high to cause the system to start the protection or reputation protection mechanism, or the motor has been used for too long or the quality of the burner is not up to par, it is recommended to find a professional repairer in the shirt section to see, now the washing machine is also very cheap, it is not worth repairing to buy a new one.

The washing machine turns off automatically after a while. That is willing to take the blind must be a small fault or a small part in the washing machine, the fuse is broken. You can call someone who understands this to help you see what the problem is in Xiangshan.

There are two possible reasons why the washing machine stops after a while:

1. Due to the external environment and excessive washing of clothes, the washing machine Zheng Zhen infiltrates the motor overheating, the motor thermal protector automatically disconnects the circuit, so that the washing machine stops working, after a while, the washing machine motor cools down, and starts to work again. In this case, please unplug the power plug first to see if the location of the washing machine is not well ventilated, or the ventilation hole at the bottom of the washing machine is blocked, and the heat dissipation is poor.

2. There are too many clothes in the washing machine, which is caused by exceeding its load, so take some clothes outside.

3. When the voltage is too high or too low or the motor fails, the washing machine may also have the above-mentioned situation, at this time, you need to wait for the voltage to be normal before using the washing machine, or find a professional maintenance master to repair it.

When using the washing machine, you need to pay attention to the fact that no matter what kind of laundry you wash, it should not exceed the rated capacity, so as not to overload and damage the motor. Do not use too much or too little water. Excessive spillage, affecting the completeness and service life of the machine; Too little will affect the washing effect, increase the wear and tear of the washed object, and the water temperature should not be too high.

When adding water, add cold water first, and then heat the water, generally the water temperature is below 40, because the high temperature is not good for some synthetic material parts in the machine.

When washing clothes in the washing machine, avoid sediment, waste water and sundries. Sand drilling into the shaft seal will wear the shaft and shaft seal, causing water leakage. If the clothes are soaked in the washing machine for a long time, the long-term water accumulation in the machine will affect the service life.

Generally speaking, there are several reasons for the sudden power failure of the washing machine during operation:

1. Each type of washing machine is marked with xx kg of washing capacity in the shopping mall, and if the weight of the laundry put in at one time exceeds this washing capacity, then it may cause the motor to be unable to withstand the phenomenon of sudden shutdown;

2. The shell of each washing machine has a special vent for the motor heat dissipation, if the vent is blocked by foreign objects, which causes the motor to overheat, the system will start the self-protection program to make the motor drive the drum to work;

3. If you have an electrical outlet at home.

If two or more high-power appliances are used at the same time, it will also cause sudden disconnection when the power consumption is reduced.

Suggested approach:

1. Put the clothes to be washed into the washing machine in batches, so that not only the washed clothes are cleaner, but also the service life of the washing machine will not be seriously shortened.

2. If the external vent of the washing machine is blocked, you only need to clean the debris that blocks the vent, and it is recommended to clean the shell of the washing machine regularly.

3. Under the condition of conditions, a special socket should be set up for high-power electrical appliances such as washing machines, so as to avoid power failure due to circuit power problems at any time.

1. When there are too many clothes in the washing machine, the washing machine is overloaded, causing the motor to overheat, and the washing machine will start the protection function and then power off. 2. When the ventilation hole of the washing machine is blocked, it will affect the heat dissipation of the washing machine, resulting in automatic power failure. 3. If the socket of the washing machine is connected to other electrical appliances, the voltage will be too low, and the power will be cut off.

Cause analysis:1In this case, it may be due to the overheating of the washing machine motor caused by the external environment and the excessive amount of washing clothes, and the motor thermal protector automatically disconnects the circuit to stop the washing machine.

2.In this case, please unplug the power plug first to see if the ventilation of the washing machine is not very good, or the ventilation hole at the bottom of the washing machine is blocked, and the heat dissipation is poor; Whether the laundry washed in the washing machine is excessive, if it is excessive, please take out part of the laundry before washing; When the voltage is too high or too low, the washing machine may also have the above situation, and it is necessary to wait for the voltage to be normal before using the washing machine.

Hello, thank you for asking the company.

Cause analysis:1In this case, it may be due to the overheating of the washing machine motor caused by the external environment and excessive washing of clothes, and the motor thermal protector automatically disconnects the circuit to stop the washing machine, and after a while, the washing machine motor cools down and starts to work again.

2.In this case, please unplug the power plug first to see if the ventilation of the washing machine is not very good, or the ventilation hole at the bottom of the washing machine is blocked, and the heat dissipation is poor; Whether the laundry washed in the washing machine is excessive, if it is excessive, please take out part of the laundry before washing; When the voltage is too high or too low, the washing machine may also have the above situation, in which case it is necessary to wait for the voltage to be normal before using the washing machine.

You are welcome to ask the company questions again.

I wish you a happy work life.

Check the power contact points, check the washing machine setting program, check the circuit board for short circuits, and check the drain sensor for foreign objects blockage.

1. It may be due to the overheating of the washing machine motor due to the external environment and excessive washing of clothes, and the motor thermal protector automatically disconnects the circuit to stop the washing machine.

2. Please unplug the power plug first, and see if the ventilation of the washing machine is not very good, or the ventilation hole at the bottom of the washing machine is blocked, and the heat dissipation is poor; Whether the laundry washed in the washing machine is excessive, if it is excessive, please take out part of the laundry before washing; When the voltage is too high or too low, the washing machine may also have the above situation, in which case it is necessary to wait for the voltage to be normal before using the washing machine.

3. For socket problems, it is recommended to use an independent socket and do not share it with other electrical appliances. It is possible that other electrical appliances have pulled the voltage of the switch down, causing the washing machine motor to shut down.

4. The computer version has loose accessories, and when the washing machine is working, the loose accessories are intermittent. It is recommended to find maintenance personnel to dismantle the cover and inspect the machine.

1. When there are too many clothes in the washing machine, the washing machine is overloaded, causing the motor to overheat, the washing machine will start the protection function, and then power off. 2. When the ventilation hole of the washing machine is blocked, it will affect the washing machine Sanzhou Li Youhe, resulting in automatic power failure. 3. If the socket of the washing machine is connected to other electrical appliances, the voltage will be too low, and the power will be cut off.

The power switch of the automatic washing machine will automatically turn off after two seconds after being pressed because there are internal parts leaking, check if there are parts of the washing machine that have touched the water, such as the computer board.

Common faults and solutions of automatic luggage washing machine:

1. The power supply voltage is unstable, check the power supply voltage.

2. The computer board is broken, and the cavity is late to replace the computer board.

3. If the communication fails, check the communication line.

4. Control loop fault, check the line.

5. The program is chaotic, replace the chip.

1. The panel door of the washing machine is not closed well or the switch of the top cover is damaged, it may also be that the switch is in poor contact, the washing machine is not allowed to open the top cover because it is a high-speed action when dehydrating, so there is a linkage switch on the top cover, and the cover circuit will be automatically disconnected as soon as the cover circuit is opened. If it is damaged, it will not move. 2. The drainage system of the washing machine is blocked or the drain valve is broken, the washing liquid in the water cylinder cannot be discharged, or there is too much foam in the water cylinder, the washing liquid in the cylinder is difficult to be discharged for a while, the water level switch cannot be reset, and the washing machine cannot enter the dehydration program.

3. The drain valve does not open the clutch conversion, and the washing and dewatering of the automatic and automatic washing machine are completed by the gear at the bottom of the solenoid valve conversion, and the damage of the solenoid valve will also make the dehydration unable to operate normally. 4. The motor performance is poor, the capacitance is problematic, resulting in insufficient output power, and the capacitor can be solved by replacing the capacitor.