My floor is flooded, what should I do? Thank you!

1. Drain the surface water on the floor in the shortest possible time.

2. If it is a small area soaked in water, it is recommended not to pry up the laminate floor to dry, which is easy to cause hard damage to the laminate floor, and it is likely to cause serious consequences that cannot be restored. It is best to quickly remove the baseboard of the floor, expose the expansion joints, and rely on the expansion joints to dissipate the moisture, which usually takes about three to ten days to dry depending on the amount of water seepage.

3. At the same time, you can also use a vacuum cleaner to suck up water vapor in the splicing gap of the soaked floor, or take a hair dryer to dry it with cold air, but do not use hot air to blow it to prevent the surface from drying and cracking due to heating and drying.

4. If it is a large area of soaking water, the floor after-sales service office should be notified in time, and the floor should be carefully pried up under the condition of keeping the floor not deformed, and placed in the ventilation place to dry according to the "well" shape, and the weight generated by its stacking to prevent deformation should be prevented.

5. It is best to replace the floor that has been soaked in water and warped and deformed, and it is not recommended to plane the arched part and repaint the treatment method, because after the arch part is planed, repainting will lead to inconsistency with other board colors, and the thickness of the whole board is uneven, the force is different, and it is easy to appear pits.

6. After all, post-rescue is passive, and taking precautions is the best choice. Usually, pay more attention to the window not to open wide to prevent rain; When you go out of the bath and enter the bedroom, you have to change your shoes; Always check the air conditioner, plumbing pipes, and washing machine for water leaks. At present, the floor wax mainly plays the role of cleaning and maintenance, can not be waterproof soaking, the best way to prevent the floor soaking is to use the floor protective film, such as a Jinchiyun brand floor protective film on the market, it has a long service life, no damage to the floor, and also saves the trouble of changing shoes at home.

Has the floor swelled? If it is inflated, what is said below is useless! The following is only to be operated immediately after the water is injected.

Find a floor installer, remove all the floors, and lay flat on the ventilated floor! Measure the moisture content in half a month! Then install it! Maybe the 2-head board can't be used, and there may be damage in the process of dismantling!

How to deal with the wooden floor if it is flooded, and the water should be removed in time.

1. If the water ingress in a small area is found in time, the ground can be cleaned, the board can be pried up, and the wet floor can be dried and reinstalled; If the water inflow is slightly large, not only should the board at the leakage be pried up, but also the opposite board should be pried up along the direction of the keel arrangement, so that the internal air circulation can take away the moisture. If you can't determine the size of the incoming water, it is best to pry up the board in turn according to the flow direction of the inlet water to check the humidity situation to be foolproof.

2. If the water ingress of the floor is serious, if there is a large area of water soaking, first pry the floor carefully, wipe the surface water dry as soon as possible, and then place it in the shape of a "well" to prevent the deformation of the floor by using the weight generated by the stacking. In addition, these floors should be placed in a ventilated place to dry in the shade and not exposed to the sun.

How to care for wooden floors.

1. Be sure to keep the floor dry and clean, and avoid contact with a large amount of water.

2. It is not allowed to scrub with corrosive liquids such as alkaline water and soapy water to avoid damaging the paint film; It can be wiped with a wrung out cotton mop, rubbed with steel wool in case of stains, and cannot be wiped with wet mops, gasoline, flammable materials and high-temperature liquids.

3. Waxing every once in a while, the time interval depends on the finish of the floor paint, it is recommended to wax at least twice a year.

4. After paving, the floor should be exposed to direct sunlight as much as possible, so as to avoid excessive ultraviolet radiation of the paint and early cracking and aging.

Most of the solid wood floors are made of paint, the paint is thick and dense, and in principle, there is no problem with soaking in water for less than 30 minutes, or even for less than 1 hour. Soaking parquet is generally fine within 30 minutes, but low-grade laminate flooring is generally not allowed to soak in water.

Specific maintenance methods for laminate flooring after immersion:

1. After the floor is blistered, the surface should be dried in time and naturally dried. If the floor is warped, arched upwards, etc., it needs to be repaired or replaced.

2. Remove the baseboard (a board at the intersection of the floor and the wall, about 15-18 cm high, also called "wall enclosure"), remove the floor in order and reinstall it.

3. Pay attention to install from the middle of the ground to the wall, first install the floor with small deformation and relatively flat, and place the deformed floor in a hidden position (such as under the sofa and bed) or the skirting board on the wall. Generally speaking, after a period of recovery, it is basically not visible from the appearance, but due to the expansion of the floor, the gap between it and the wall will be relatively smaller.

4. The arch height of the floor is more than 3 cm, and the surface is uneven, warped or deformed after disassembly, it is recommended to contact the manufacturer for repair or replacement. On the one hand, the manufacturer's charge is relatively low, and on the other hand, the manufacturer has the same model of floor stock, and the repair effect is better.

5. Regardless of the size of the soaked area, it is not recommended to pry it up to dry, so that the floor will not be able to be used again. The correct way to do this is to quickly drain the surface water of the floor, remove the baseboard, expose the expansion joints, and rely on the expansion joints to dissipate the moisture.

Specific maintenance methods after solid wood flooring is soaked in water:

If the solid wood floor enters the water in a small area, the water vapor can be sucked out with a high-power vacuum cleaner, but the water in a large area needs to be pried up and dried in the shade.

It is a very embarrassing and annoying thing for the floor to be flooded and damp. If left untreated, it can cause serious damage to the floor and may even affect the quality of the entire home. Here are some countermeasures:

1.The first thing to do is to turn off the water source and remove as much of the flooding as possible.

2.If it is only slightly damp, you can use a household vacuum cleaner to absorb the moisture on the surface, and then place it for ventilation and dehumidification or pin to dry the source.

3.If the dampness is severe and is not treated in time, it is recommended to use equipment to dry the floor and room. You can choose a specially rented drying equipment or DIY homemade one.

4.If the floor has shown severe swelling, you can try to use carpenter's glue to force the swelled part in place, but this is only a stopgap measure, and it is recommended to replace the floor with a new one as soon as possible.

5.If your floor is a solid wood floor, you will need to flip the floor first and then treat it on the back. Place the desiccant on the back of the floor and use a thin iron sheet to prevent the desiccant from sticking to the floor.

The gap between the wet core layer and the solid wood panels above can also be dried behind the floor.

6.After all treatments, it is important to thoroughly clean and disinfect the floor to avoid adverse effects on the health of you and your family.

In conclusion, the floor is flooded and damp, and if treated in time, it will not cause too much trouble to your family life. You can choose the most appropriate treatment method based on your actual situation.

Laminate flooring is a very popular flooring material, which is more and more popular among people due to its beautiful appearance, wear resistance, easy maintenance and other advantages. However, in daily life, there is a possibility that laminate flooring can be flooded due to various reasons. Here are some suggestions for how to deal with flooding in laminate flooring:

1.Remove stagnant water as soon as possible: If you notice that your floor is flooded, you should remove it as soon as possible with a tool such as a water suction device, towel, or rag. Pay special attention to the stagnant water in the grooves and crevices of the floor and remove it completely.

2.Use a dehumidifier: After the laminate floor is flooded, the humidity in the room will increase, which can easily lead to mold and deformation of the floor. Therefore, after removing the stagnant water, a dehumidifier can be used to reduce the humidity in the room and avoid moisture on the floor.

4.Peeling and replacement: If the floor is obviously deformed, falling off, floating, etc., it may be necessary to peel off and replace the damaged floor.

5.Care and maintenance: If the water infiltration is not serious during the flooding of the floor, it is recommended to care for and maintain the floor. Use an absorbent towel to wipe the floor to avoid moisture trapped on the surface of the floor, remove stains and dust, and use floor protectors, etc.

Finally, in order to avoid flooding of laminate flooring, there are some issues that can be paid attention to when installing the flooring. For example, fill the ground and under the floor with insulation materials to avoid rain and water leakage from seeping under the floor; Before installing the floor, the floor should be completely cleaned to avoid water accumulation and greasy on the floor, which will affect the effect of Anhu simple installation.

If you are a solid wood floor, you should quickly disassemble the wooden floor to dry, and at the same time wipe the anti-chao layer dry, (find a professional to deal with it), if it is a composite floor, I think it is not saved, even if it is dry, it will be deformed because of moisture.

Laminate flooring can not be blistered, after blistering the MDF will swell, the floor bulges, it is recommended to remove it immediately to view, the swollen board should be replaced immediately, it is best to replace it all.

Wood products are water-resistant. Try to avoid soaking with water when doing cleaning.

Be sure to wait until it dries.

Apply wax or essential oils.

And regular maintenance.

In terms of cleaning, you should also pay attention to the wooden floor is very squeamish.

Sports wood flooring is soaked and swollen by water: sports wood flooring is water-abore, and the sports wood floor after being soaked in water is easy to swell and deform, which directly affects the use of sports wood flooring. Generally, when encountering this kind of problem, do not remove the wooden floor without permission, and contact a professional wooden floor installer to repair and deal with it according to the soaking situation.

What to do if the wooden floor is blistered.