How to increase the water in the urinal? How to adjust the amount of water with the urinal sensor

How to increase the water in the urinal this to change the valve, and then adjust the pressure of this water droplet if you say. The water supply pressure is low, then you can add 1 booster pump. There are many public toilets with booster pumps.

The faucet of the outlet pipe can be replaced with a larger diameter, or the volume of the water tank can be increased.

If you want to increase it for him, you can remove the original one for him, and then replace it with a new one or send a new one, so that you can do it, relatively speaking, you can.

It has two keys, you can press the one that increases the water, and that's how it is usually designed.

There is a rose at the top of the automatic flush valve of the urinal, and you can adjust the small amount of water by turning right with the driver, and the amount of water can be adjusted by turning right to the right.

How to increase the water in the urinal? You make the water pipe thicker, you can fill it with a little bit of water, you have to make that kind of U-shaped channel bigger and thicker, and then fill it with water. This can be added to the urinal water.

How to increase the water in the urinal? You can put the water in the urinal. Water. Rinse often. In this way, the water in the urinal will become larger.

Are you talking about toilets? If it's a toilet, you should install it a little deeper, so that there will be more water in it.

Hello, if you want to increase the water in the urinal, it may be due to the low water pressure, so you can add a pressurized pump, which is conducive to the increase of the water.

If you want to increase the water in the urinal, you can put the flushing of the one. Tree. The gate valve inside the box is enlarged a little more, so that the water will be more flushed.

That handle can be adjusted. There's a screw in it. You can adjust it slowly Is it a flush toilet? You open the inside of the water storage, there is a float inside, you can adjust the depth, if it is a direct water pipe flushing, it may be that the pressure of your tap water is less.

You can thicken the urinal pipe.

Then the water pipe is pressurized, and the amount of water in it becomes larger.

Hello , that handle can be adjusted. There's a screw in it. You can adjust it slowly Is it a flush toilet? You open the inside of the water storage room, and there is a float in it, which can adjust the depth

If you want to increase the water in the urinal, you can only deepen or increase the area, so that you can increase the water in the urinal.

Increase the amount of water in the water valve.

I think it's just a matter of reshaping it, and then the range inside is basically controllable, and then the size of it can be adjusted, and you can separate them at the beginning of the production so that you can achieve a really good result.

How to increase the water in the urinal? If you want to make it bigger, just turn on the faucet.

How to increase the water in the urinal? You can find someone from the renovation company, or you can go to the market where the renovation is responsible for the renovation and consult the workers there and ask them to help fix it.

If the water in the urinal is increased, you can directly replace the pipe with a large one.

Hello, of course, it's better to enlarge the hole or flush things away, and it's not good to urinate too much water, because it's a waste of water.

You can enlarge the side so that it can be enlarged, which is also very convenient.

How to increase the water in the urinal? You can dig another bowl of urinals, and the area will become bigger and wider?

If you want to increase the urinal water, you can buy an extra large urinal.

Hello, there is a possibility that it is blocked, you can check it out, or add a pump.

Just dig another septic tank next to it, and then from the septic tank next to it, it can flow in when it is full.

If you want to increase the water of the urinal, you have to control this, and you have to look at the installation manual of the urinal and the electronics.

This should be emphasized, the pool does not belong to the water supply and drainage major, the pool size is determined by the architecture major, and the water supply and drainage major is only responsible for the pipes. There are many similar problems, such as the size of drainage ditches and sumps, and the slope of the roof rainwater bucket.

How to increase the urine draft, you can increase it from that tank.

This is related to the design, if the water outlet is small, there is no way to artificially change it.

If you want to increase the water in the pool, you can increase it appropriately according to your requirements. I hope it can help you.

Summary. The urine sensor is divided into two parts, of which the sensor is the circuit part, and its task is to open the sluice gate as soon as the person walks away, so if you want to adjust the amount of flushing, in the case of the water pipe and water pressure unchanged, it is to adjust the opening and closing time of the water valve of the urine sensor, and if the time is extended, the amount of water is large, and if the time is shortened, the amount of water is small. Depending on the water pressure, the flushing volume of the pee sensor can be adjusted by itself.

The specific adjustment method is as follows: remove the control panel of the sensor, use a flathead screwdriver to rotate the slotted bolt on the water volume adjustment, and choose counterclockwise to increase the amount of water, otherwise to decrease the amount of water until the water source is turned off.

The urine sensor is divided into two parts, the medium-sized excitation sensor is the circuit of the part, its task is to open the sluice gate as soon as the person walks away, so if you want to adjust the amount of flushing, in the case of the water pipe and water pressure unchanged, it is to adjust the time of the water valve of the urine sensor. Depending on the water pressure, the flushing volume of the pee sensor can be adjusted by itself. The specific adjustment methods are:

Remove the control panel of the sensor and use a flathead screwdriver to rotate the slotted bolt on the water volume adjustment, counterclockwise to increase the amount of water and vice versa to decrease the amount of water until the water source is turned off.

Oh my God, you've said a great job! Can you elaborate on that?

The urine sensor is based on the principle of infrared finger rental line induction, and sends a signal to the pulse solenoid valve to automatically control the flushing through the human body induction. At the same time, according to the frequency of use of the urine sensor and the time of each use, intelligent flushing control can save water more effectively. The common urine sensors in life are controlled by microcomputer, which will automatically adjust the sensing range according to the working environment, without manual adjustment.

The pee sensor is equipped with a water volume regulating valve and a filter, so even non-professionals can easily adjust the water volume and clean the filter.