If the shower head is blocked and you want to dredge it, how should you dredge it?

White vinegar cleaning method: the shower head shower is blocked, first remove the shower, and then put it into a basin with white vinegar to soak for two hours, after soaking, we will use a toothbrush to wash it, and finally wash it with water. It is best not to use strong acids when cleaning shower heads, as strong acids can corrode the plating of the shower.

Moreover, a large number of holes are blocked, so it is recommended that you use acidification and dust removal to solve the problem of shower shower blockage. You will need to prepare some white vinegar and pour it in a basin so that the shower head can submerge it. After about 10 minutes of soaking vinegar, you can remove the limescale from the shower head.

It can effectively extend the life of water appliances at home, so it is necessary to install a pre-filter, and the second reason is that the shower is not selected correctly. There are two solutions, one is to install a pre-filter to improve the quality of water in the home, and the second is to change the shower. In the case of a slight blockage, only the shower head needs to be disassembled and rinsed.

However, if the blockage is serious and it has been a long time, it is necessary to use acidification and dust removal methods, and use white vinegar to soak the disassembled shower for ten minutes, and then you can remove the scale for a long time.

Soak the vinegar for a few hours, then poke open the hole that is still blocked with a needle, rinse it with water, and put it back in. Or you can squeeze out the toothpaste, turn it into water, and put the shower head in it. This will allow you to rinse with clean water in a while, and you will find that the shower head is already unobstructed.

Please note: Do-it-yourself showering, using safe products that can be reloaded for a period of time after the seam has passed through the water, removing or reducing the limescale effect on the shower, can act as an acid spill and some antiseptic.

Unplug it firstand turn off the cold water angle valve and hot water angle valve under the water heater at the same time. Remove the restraint of the pressure relief valve and connect it to the plastic pipe. Open the pressure relief valve, rotate the pressure relief valve wrench 90°, and disassemble the metal pipe joint of the hot water pipe, the water heater will produce scale, which will affect the use effect of the electric water heater, and the energy consumption is high, and the service life will be reduced, so the electric water heater should be cleaned carefully.

Most of the nozzle is blocked because of scale, you can buy some spray to eliminate scale, spray on it to dissolve scale. You can also soak it in vinegar for a while. Or use a needle to hollow out the blocked area.

You can use a toothpick to poke open the blocked eye, or you can put citric acid in the water and soak the nozzle in it to dissolve the dirt in it.

If the nozzle is blocked, you can soak it in white vinegar, which can dissolve the scale well and make the nozzle more enjoyable.

Today's shower heads can be unscrewed, just unscrew them and clean them.

Dredging shower skills: 1. Prick with acupuncture, 2. Soak with vinegar, 3. Use lubricant, 4. Wipe with a towel.

1. Use acupuncture: the pre-prepared needle will pierce the impurities in the blocked hole, and when the impurities are scattered, they will be washed out along the water flow until there are no impurities in the hole.

2. Soak with vinegar: It is advisable to pour vinegar into a basin so that the shower head can be immersed. After about 10 minutes of soaking vinegar, you can remove the limescale from the shower head. It is suitable for a large number of blockages in the shower head.

3. Use lubricant: If the metal of the shower head is rusty and the blockage is very serious, then you can use the anti-rust lubricant.

4. Wipe with a towel: This is a more traditional method, which is generally more suitable for the shower that has been around for a certain number of years and has an older appearance.

First of all, remove the nozzle, then divide it into several parts, then go to the cleaning in stages, and then assemble it.

At this time, you should unscrew the nozzle first, and then do a simple cleaning of the clogged things inside, and finally install it, so that you can continue to use it.

At this time, you can use some anti-scale cleaning liquid, and then you can also put this shower head into a baking soda basin to soak for a while, and then rinse it with clean water.

You can find a way to clean some of the impurities in this shower head, open the shower head, and look at the leaky holes inside.

We can remove some white vinegar, baking soda and dish soap in the shower head, and we can also go to some toilet cleaners and let them stand for a while, so that they can play a role in dredging.

What is the reason why the shower head at home is blocked after being used for a period of time? What should I do? Here's some advice for you.

Introduction to the solution to the blockage of the shower head.

If only some small holes are not smooth and cause the shower head to be blocked, the easiest way is to use a small needle to take the puncture, and first pay attention to the safety of the hand when using a small needle to puncture through, this method is not suitable for the shower head made of plastic, because it will cause the hole to become larger and the water pressure is uneven after a long time.

Disassemble the nozzle for cleaning.

This can make the inside of the shower head cleaner, and you don't have to worry about what to do if the shower head is blocked, which is also the best way to solve the problem of the shower head plugging and plugging. The dismantling and cleaning position is mainly for the cleaning of the filter screen and the cleaning of the connection between the handle and the hose.

Soak in vinegar The blockage of the shower head is most likely caused by the clogging of the outlet hole by limescale after long-term use. If it is only slightly blocked, you only need to disassemble and clean the shower head. If the shower head has been blocked for a long time, and a large number of holes are blocked, it is recommended to prepare some white vinegar and pour the vinegar into the basin so that the shower head can be submerged.

After soaking the vinegar for 10 minutes, you can remove the limescale from the shower head.

Use lubricants The nozzle material in everyone's home is different, and the solution is also different. If the shower head is clogged due to rust in metal, it is recommended to use a rust removal lubricant. This anti-rust lubricant allows the metal to have better permeability.

Separate the rust layer from the metal layer and leave a protective film so that the shower will never rust again.

Replace the nozzle Choose the nozzle as much as possible to be made of copper material, because the stability of copper is relatively strong, and it is not easy to rust. When purchasing, it is best to buy products that have passed the commodity inspection in the large-scale **, after all, a rain shower head is not short to use Dahuiqiao, and choosing a good shower head can bring us a higher happiness index.

In addition, when purchasing, be sure to check the water output of the product, generally speaking, the quality of the sprinkler head can ensure that the water distribution of each hole is basically the same, of course, the water-saving function is also a part that needs to be considered when purchasing, for example, some showers use steel ball valve core, and then equipped with a hot water controller, which saves 50% of water compared with ordinary showers.

What is the cause of a clogged shower head?

Some families will encounter the situation that the shower head has been used for a period of time and does not produce water, is it necessarily that the shower head is broken? Not necessarily. This is not only the cause of the blockage of the shower head, but also the small hole of the shower head due to the formation of scale after the shower head has been waterproof for a long time, or it may be due to the rust of the metal of the shower head blocking the hole.

What is the best solution to this blockage? Let's move on.

If the shower head is blocked, it's easy to unclog it. The main thing is to avoid using strong acids to remove scale, and it is best to use white vinegar to clean the shower head. Be careful not to touch the shower head during the cleaning with white vinegar.

Let's follow life slowly and take a look at the specific dredging methods after the shower head is blocked.

First of all, it's only natural for shower heads to get clogged after a period of use. This doesn't mean that the showerhead is broken. Don't worry, you don't need to buy a new one at all.

This is due to the limescale that occurs after long-term drainage. You just need to disassemble and clean the shower head.

Many people hear that disassembling and cleaning can be a hassle. In fact, the operation is very simple. It doesn't require you to completely disassemble the shower head piece by piece. The most important thing is for you to clean the showerhead.

Secondly, the most important raw material for cleaning the nozzle is white vinegar, white vinegar is also a material in the home. After removing the shower, we put it in a small basin filled with white vinegar and soaked it for about two hours. After soaking, scrub with a toothbrush.

Then rinse with water; If there is a hard water precipitate, scrub it with lemon slices.

Of course, when cleaning the shower head, it is necessary to pay special attention not to use strong acids (white vinegar is best) so as not to cause corrosion to the surface of the shower head. In order to ensure that the sprinkler head does not clog, it is best to clean the sprinkler head every six months or less, so that you don't have to worry about the sudden blockage of the sprinkler head when taking a shower, which will affect your mood in the bath.

To ensure the longevity of the showerhead, it is best to keep it away from the bathroom heater at a distance of more than 1500 px, and often wipe the surface of the shower with a soft cloth and a little flour to keep it as new. The above is the solution to the blockage of the shower head, I hope it can help you. Everyone should also pay attention to the maintenance of the shower head in daily use.

You can remove the shower head and use a needle to get the contents out, and you can dredge it well.

Replace a shower head directly, so it's okay, the ** of the shower head is not very expensive, and it is more convenient to buy a new one.

You can use a needle to dredge it, so that you can get the dirt out of the shower head, or you can use a wire to dredge the shower head and make it smoother.

At this time, you need to remove the shower head, and then rinse it with clean water, or you can use some strong detergent, or you can dredge it.

It is natural that the shower head will be clogged after a period of long-term use, which does not mean that the shower head is broken.

What to do if the shower head is blocked.

If the shower head is clogged, if it is due to the limescale generated after a long period of draining, you only need to disassemble and clean the shower head. Many people may find it troublesome to disassemble and clean, but in fact, the operation is very simple, it does not require you to completely disassemble the shower head into pieces, the most important thing is to let you clean the shower head.

After we remove the shower, put it into a small basin with white vinegar and soak it for about two hours, after soaking, brush it with a toothbrush, and then clean it with water; If there is hard water sediment, scrub with lemon slices.

To clean the shower head, special attention should be paid not to use strong acid (it is best to use white vinegar), so as not to corrode the surface of the shower. In order to ensure that the shower head is not clogged, it is best to clean the shower head every six months or less, so that you no longer have to worry about the sudden blockage of the shower head when taking a bath, which will affect your bathing mood.

Precautions for cleaning shower heads.

1. Please pay attention to your own and the safety of the product when disassembling and assembling the shower

2. The filter gasket can not be used, the mesh is too large or too fine, too large may not have the effect of filtration, too fine may affect the flow rate, the specification of the filter screen is 40-60 mesh.

3. Do not use strong acid when removing scale, so as not to cause corrosion on the surface of the shower.

4. Do not disassemble the shower for maintenance, improper dismantling will cause damage to the appearance and internal structure of the product.

5. The ambient temperature of the shower should not exceed 70C, and the high temperature and ultraviolet light will greatly accelerate the aging of the shower and shorten the service life of the shower, so the installation of the shower should be as far away as possible from the heat source of electrical appliances such as bath bombs. The shower should not be installed directly under the bath bomb and should be at a distance of more than 60cm. Shower head maintenance knowledge.

1. The ambient temperature can not exceed 70 degrees Celsius, high temperature and ultraviolet light will greatly accelerate the aging of the shower and shorten the service life of the shower, so the installation of the shower should be as far away as possible from the heat source of electrical appliances such as bath bombs. The shower should not be installed directly under the bath bomb and should be at a distance of more than 60cm. 2. In areas with hard water quality, please try to choose a shower with a glue particle outlet hole or a direct cleaning device, even if the shower outlet hole is blocked by scale, it is easier to clean.

Remember not to forcibly disassemble the shower, due to the complex internal structure of the shower, non-professional forcible disassembly will cause the shower to not return to its original state.

3. When opening and closing the shower faucet and adjusting the water outlet of the shower, do not use too much force, and gently turn it with the trend. Even a traditional faucet doesn't require a lot of effort. Special care should be taken not to use faucet handles and shower brackets as handrails to support or use.

4. The metal hose of the shower head should be kept in a natural stretch state, and it should not be coiled on the faucet when not in use. At the same time, pay attention to the joint between the hose and the faucet to avoid breaking or damaging the hose.

Shower heads blocked can do this:1. Soak the nozzle in white vinegar, wash it with a toothbrush after a period of time, and rinse it with water.

2. Use a needle or a fine toothpick to pierce the small hole of the nozzle to remove the internal impurities.

3. If the nozzle is rusty and causes blockage, you can use anti-rust lubricant, and a protective film can be produced during the removal process, which can prevent rust again in the later stage.