-
It may be that the network cable is not in good contact.
-
Cause: The network icon is turned off in the system icon in the notification bar. The following uses the win7 system to demonstrate the solution process:
1. Turn on the computer, right-click on the blank space of the taskbar, right-click on the dish-car-click properties.
Second, then enter the taskbar interface and click the custom button in the notification area.
3. Find the link to open or close the system icon and click to enter.
Fourth, finally set the network display status to open, and destroy it before clicking to hit the Wisdom Hengding button.
5. As shown in the figure below, after setting, the network icon will be displayed in the notification bar.
-
If you are using Unicom Broadband and cannot connect to the Internet, there may be one of the following reasons:
1. If the payment is in arrears or due, it needs to be paid or renewed in time.
2. If the network cable is loose, both ends of the network cable need to be plugged in tightly.
3. If the device is used for a long time, you can turn off the power of the optical modem, router, computer and other Internet access equipment for a few seconds, and then turn on the power to restart.
4. If the above methods cannot be restored, it is recommended to contact the local customer service staff of the hot shelter cong line.
-
1. Turn on the computer, click on the computer, and right-click on the "Sock Management" option.
2. Next, you need to click "Device Manager" again, as shown in the figure below.
3. Click "Operation" through the Device Manager Portal, and then click "Add Obsolete Hardware".
4. Next, it will be displayed in the hardware of the dissipation, as shown in the figure below.
5. Finally, it was found that it was back to normal, as shown in the figure below.
-
Install the Driver Wizard with a network card driver.
There are diagnostics in it.
-
Check your network! Cable! , you don't even send a picture? Is it really asking questions? It's all a guess?
-
1. Check whether the driver of the wireless network card is installed correctly.
2. Check whether the wireless network card is installed in place.
3. Check the relevant settings to see if the network connection icon is displayed.
-
Check your network cable for loose connections.
If you are connected to WiFi, check whether there is no network on WiFi.
-
The system turns on the airplane mode, so naturally there is no network to exit the airplane mode.
-
Turn off airplane mode.
-
Hello, dear ask the user, hello, I know the high-quality answer, I have received your question, I will reply in time after reading, please wait for a while, after asking, because there are too many lists, it will be in turn, it will not be not, please be patient! ❤
My computer is connected to the Internet, why is it not displayed?
Okay, wait a minute.
It's this little circle that keeps turning, as if there is no network, but there is a network, what is the problem?
Dear, there is a network display.
This is the icon that is already connected to the network.,It's a red x if you're not connected to the network.,As long as you can open the web page, it's connected to the network normally.。
Listen to you, you should use the dial number. You should use the cat directly on the net. No routing, only you are using your network cable? >>>More
This file is a help file for the network group component, when there is a network dial-up and other problems, the system prompts that the file is missing, which actually means that your system does not have this help file, and can not immediately display the solution and suggestions of the problem, that is, this file is a help document, not an important file of the system to be used on the Internet! >>>More
If there is no red cross on the computer icon, it means that the physical connection is connected Then it is a problem with the configuration Solution: 1, restart the cat 2, restart the router 3, automatically get the IP and change it manually, configure one yourself and the router in the same network segment, try 4, manually change the IP back 5, absolutely can
Check whether the network cable connector is loose.
The phenomenon of a successful broadband connection but not being able to open a web page is now very common, and the main reasons for this phenomenon are as follows:1There is a problem with the DNS of the network connection. >>>More