How to make a hamster water dispenser? How to make a drinker for a little hamster

Updated on pet 2024-06-19
6 answers
  1. Anonymous users2024-02-12

    Actually, hamsters.

    Drinking fountains are available online, but if you can make your own, you might as well DIY yourself. Let me briefly teach you. The first thing to do is to look for a mineral water bottle cap or other beverage bottle.

    The lid is also available. Wash and disinfect it, and then prepare some *** double-sided tape.

    Pick a suitable place in the cage. Then, put some double-sided tape on the underside of the cap to better hold the bottle in place and prevent the hamster from knocking over the bottle. Of course, double-sided tape sticking to the bottle is fine, don't use it superfluously, if the hamster is stuck with double-sided tape when drinking, it will not be good.

    In this way, a very simple hamster drinker is complete. This is the easiest way to make it, but if you have other ideas or new inventions, you can try them yourself. It's also a joy to make a drinker for a hamster.

  2. Anonymous users2024-02-11

    Hanging drinker making Prepare plastic bottles, hang them upside down on the hamster cage, and plug the mouth of the bottle with a straw. The outlet of the kettle should be sealed with a rubber stopper, which can ensure that the kettle does not leak.

    Placing a small plate on the bottom, then turning the ashtray upside down to hold down the plate, you can place a straw in the notch of the ashtray. This way, the hamster will be able to drink without falling into the water.

  3. Anonymous users2024-02-10

    There is a special hanging bottle for hamsters to drink water, and they will hang the bottle when they are thirsty. You can have water in a day.

  4. Anonymous users2024-02-09

    Because the small size of the little hamster, its drinker is still relatively easy to make, and the specific steps are as follows:

    1.First of all, generally speaking, a larger drink bottle cap can meet the daily drinking water of hamsters, so look for a suitable drink bottle cap first.

    2.Then, prepare a roll of double-sided tape, if you can't find the double-sided tape with glue, but note that the glue is not very convenient when cleaning the pool in the later stage.

    3.Finally, find a suitable position in the cage, glue the cap to the selected position, and check whether it is flat and firm.

    4.Such a simple drinking fountain is ready, pay attention to observe more to see if the little hamster is not adaptable.

    In addition, remember to change the water frequently, do not wait for it to drink the water before changing, at that time the hamster has often drunk a lot of dirty water, easy to get sick, so it is recommended to change the water for the hamster at a fixed time every day, and to clean the pool regularly to avoid dirty water causing the hamster to get sick.

  5. Anonymous users2024-02-08

    You can temporarily get a bottle cap of mineral water and fill it with most of the water for the hamster to drink.

    Note: The container for water should not be too large, (less than half the body of the hamster) and it is very troublesome for the rat to knock over the water.

    So it's still recommended to buy a hamster drinker. The market price is about 10 yuan, and it can also be bought with a cage, which is more cost-effective.

    Of course, if the landlord wants to DIY, it's okay, this is what I saw in a post (original: hahasinian), the steps are as follows:

    Materials: Prepare a popsicle, a wire, a straw, a cotton swab, a strap to tie the water pipe.

    1. Eat the popsicle first, leave the tube, and then cut a hole in the head of the tube.

    2. Prepare a straw to leave the bendable section.

    3. Stuff cotton in the straw as compact as possible The compactness of cotton directly affects the water flow speed of the pipe, and both ends should be plugged.

    4. At this time, you can insert the tube into the popsicle and wrap it around with that kind of tape, and mine will not leak after wrapping it.

    5. Add water to see the speed of the water dropping on the head If it is too fast, continue to stuff the cotton When you feel that the water flow speed is about the same and drip slowly, prepare a cotton swab with a wooden stick to break it and stuff the wooden stick into the straw with the head Remember to plug the stick upside down The wooden stick goes in first.

    6 Leave a small part of the cotton swab head outside, the water will slowly soak the cotton head, and form a water balloon, and the small ss can drink the water.

  6. Anonymous users2024-02-07

    There are many ways to make a hamster water dispenser, and here's a simple and easy one:

    Materials: 1a clean plastic bottle (it is recommended to use more than liters, see how many hamsters you have can increase the size of the bottle accordingly);

    2.a plastic water pipe;

    3.a pliers fitted with a metal needle;

    4.a pair of needle-nose pliers;

    5.a sharp blade or an ultra-fine drill;

    6.Some thin copper wire or plastic rope.

    Step Hunger Coincidental Trouble:

    1.First, cut a section in the middle of the plastic bottle, which is about the size of a hamster can drink;

    2.Using the pliers of a metal needle, drill two holes in the bottle: one at the top and one at the bottom; Rotten cover.

    3.The hole at the top should be slightly larger to allow the drinking tube to pass through;

    4.At the hole below, use needle-nose pliers to cut a small section of plastic pipe to make it L-shaped;

    5.Use a sharp blade or electric drill to drill a small hole under the bottle so that the L-shaped plastic tube can stick out from the inside of the bottle;

    6.Tie the L-tube to the lower hole of the bottle with a thin copper wire or plastic rope to hold it in place;

    7.Wrap a loop of copper wire or plastic rope around to secure the bottle to the cage.

    This way, your hamster has a convenient and easy-to-drink water dispenser. You can also decorate the bottle if you like: put a cute sticker on the bottle or draw on it with colored pencils.

    In conclusion, the process is very simple, does not take long, and is a DIY project that every hamster owner can try.

Related questions
7 answers2024-06-19

My hamster also makes a lot of things by himself, and the mud can be used as a reference. No matter what you make of the cage, remember that it must be big, he likes to play, and it needs to be covered with something, and it will be easy to climb out when he is big. The box of food can be a little shallower, and he doesn't plan it too much. >>>More

15 answers2024-06-19

o( oHa! It's a coincidence that my ss has the same problem. I once witnessed his crime by pushing the nest material next to the kettle, and then the water in the kettle was sucked clean by the nest material.

22 answers2024-06-19

The target group of the water dispenser refers to the object subject to which the water dispenser is applicable, which is mainly divided into 1: the application subject of the family unit; 2: The application subject of government agencies, organizations, industrial and mining enterprises; 3: >>>More

10 answers2024-06-19

As for the water dispenser, in terms of its function, you don't have to pay too much attention to the brand. Haier's washing machines are the leader in the industry, and every home appliance brand wants to rely on its popularity to dominate the home appliance industry. In terms of the qualification of making water dispensers, you don't have to choose Haier, choose a cost-effective one.

16 answers2024-06-19

Professional cleaning agency, the algae is a green algae formed by mineral impurities and dust in the air, drinking such water is easy to spoil the stomach, if there is such a thing, find a green source water dispenser professional cleaning agency, see where you have this point, if there is, you can let their staff clean you, and sterilize at the same time. >>>More