How to get the beautiful sewing, how to operate the beautiful sewing

Reminder: Because of the requirements of the construction of the sewing agent, 1 should be dry, and 2 should be free of dust. Many processes in home decoration will produce a lot of dust, such as tiling, carpentry, and lacquer workers will also produce putty ash falling.

1. Reserved design of tile joint width: generally ceramic tile joint reserved 1mm-8mm wide, 1mm-2mm deep, narrow tile joint after the overall effect is good, the brick joint is wide after the three-dimensional effect is good, the sense of hierarchy is strong, and it is easy to control the collection size error is small.

Second, reserved tile joints: can be used to locate the cross embedded in the tile joint, easy to ensure that the width of the brick is consistent, and then use ordinary cement or white cement to pave the bottom of the joint, after filling the willow will be used to flatten the joint, compacted, so that the depth of the joint is kept around the appropriate.

3. Drying period: After the bottom filling is completed, the cement material in the joint can be dried thoroughly, and the dust in the tile can be removed with a rag for the joint construction of the beauty joint agent.

How to get beautiful sewing.

When tiling tiles, everyone will be treated with beautiful seams, which is not only beautiful and stylish, but also prevents stains from remaining in the gaps of the tiles. So how to sew beautifully? What should I pay attention to in beautiful sewing? Let's take a look!

How to get beautiful sewing.

1. Seam cleaning. You should first use a utility knife or sewing cone to clean up the dust and impurities in the gaps, then use a brush to clean up the impurities and dust, and then use a semi-dry towel to wipe the gaps and both sides, so as not to affect the effect of the sewing.

2. Paste masking paper.

After the gap is cleaned, you can't start work immediately, but paste masking paper on the edge of the tile before gluing, so that the beauty grout will not drip onto the non-slip bricks and antique bricks, so as to avoid subsequent cleaning troubles.

3. Gluing. Whether it is a single tube or a double tube of sewing agent, the nozzle of the glue gun should be used for construction, and the sewing agent should be squeezed into the gap, but the frequency of pressing the glue gun and the speed of the glue gun movement should be smooth during construction, not too fast, and the uniform and slow speed can ensure that the glue is smooth and balanced.

4. Pressing seams. During construction, it is necessary to gently compact the seam ball when it can flow while the beauty seam has not yet solidified, and trim it, so that there are micro grooves in the gaps of the tiles to prevent scratches caused by daily life.

5. Shovel glue. If the temperature is relatively high and the indoor garden is relatively dry, the sewing agent can be dried in 24 hours, if the weather temperature is relatively low and the indoor is more humid, you should wait for 48 hours, and then the tiles without masking paper can be scraped off with a spatula.

What to pay attention to in the beauty sewing:

1. Before construction, be sure to clean the tile gaps, otherwise the tile gaps are likely to be black and moldy.

2. It is best to use up the sewing agent at one time, if it is really not used up, you need to remove the hose, wrap it in a plastic bag or old newspaper, and replace it with a new nozzle during the next construction.

3. The construction of the sewing agent should be before the furniture enters, so that it is not used to move the furniture back and forth.

4. In addition, the sewing agent is a quick-drying type, and the seam should be pressed within 30 minutes after the blowing, otherwise it will be difficult to press the seam after the initial setting.

The steps for beauty sewing are as follows:

Tools and materials are prepared: shovel, plastic gun, yin and yang corner seam, sewing ball (ice cream stick), brush, masking paper or masking wax, sewing agent.

Step 1: Clean.

First of all, the gaps of the tiles should be cleaned, and the dust and impurities should be cleaned up, and the manual cleaning is more thorough than that of the motor driving the grinding wheel. In addition, there should be no water or moisture in the gaps, which will affect the curing and discoloration of the sewing agent.

Step 2: Apply masking paper or masking wax.

Masking paper needs to be aligned, and masking wax is more convenient to use, just rub it on both sides of the gap. If the tile surface is smooth, not matte or matte, this step can be dispensed with.

Step 3: Fill with sewing agent.

The width of the nozzle should be slightly narrower than the width of the tile joint, and the material about 40 cm from the front end should be extruded before operation. Ceramic tiles leave a gap of 3-4 mm, the effect of filling the joint agent is the best, the surface filling is enough, and the cost of filling will be 2-3 times.

Step 4: Pressing the seam.

The purpose is to make the sewing agent show an inner arc shape and prolong the service life of the sewing agent. The sewing agent has the characteristics of quick drying, and at most about 1 meter, it is necessary to press down at a 45-degree angle with a seam ball for compaction.

Rush through the gaps in the tiles with consistent force. If the pressure is deviated, it will make one side a pit, and if the strength is uneven, it will make the sewing agent uneven.

It is best to do it in one go, if there is a place that is not well operated, it is necessary to start from the beginning, not from the middle, and do not press back and forth, try to operate two people together, you can avoid forgetting to press the seam.

Step 5: Remove excess sewing agent.

In summer, the seam is cured quickly, and after 5-6 hours, you can use a shovel to remove the excess seam on the tile, achieve basic curing in 24 hours, and complete the complete curing in 7 days.

Ceramic tile is a decoration material used in every family, and laying smooth and clean tiles on the ground can not only increase the decoration of the house, but also bring great convenience to the cleaning in later life. However, the tile will leave a gap when it is paved, and then it is necessary to carry out tile seamping, thenHow to do tile seamsThis? Let's take a look at the methods and precautions for tile seaming.

How to do tile seams

1. Tools preparation: glue gun, wallpaper knife, silicone scraper, small bucket, masking paper.

2. Choose the color of tile grout: Generally, customers determine according to their own preferences.

3. Operation steps: cut a hole at the bottle mouth of the tile joint, then screw the discharge nozzle on, and then use a wallpaper knife to cut the discharge nozzle into a 45-degree angle, if the tile joint is less than 2 mm, cut a small slope angle at the front end of the discharge nozzle with a wallpaper knife; If the tile joint is greater than 2 mm, then you can cut off an extra section; The width of the discharge nozzle must be less than the width of the seam to ensure that no material is wasted.

4. Construction method:

a. After entering the house, the ground should be cleaned, and then the filling in the tile joints and on both sides should be cleaned with a wallpaper knife, and the ground should not have floating dust.

b. Quickly wipe the tile joints after wetting the sponge with water to ensure that there is no dust, use a glue gun to evenly hit the material in the brick joints, apply about 1 meter, and block the discharge nozzle.

c. Then use the silicone board to scrape the material immediately, and a small amount of material overflows on both sides of the brick joint, wipe it off with a slightly damp sponge, wipe it several times, and the sponge should be cleaned with water frequently.

d. Wait for an area to be done once and then hit it a second time from the beginning to ensure the quality of construction.

5. Construction quality standards: It must be smooth and not edged, there can be no bubbles and small pits, and the brick surface can not overflow, and the ground must be clean before going out.

6. If the customer is constructing by himself and is afraid that the overflow on the brick surface will not be clean, then you can use masking paper to stick it on the edge of the brick joint, and then use a glue gun to beat the material, scrape it flat with a scraper, and wait for the material to dry, and you can open the masking paper after repairing.

What are the precautions for tile seams.

1. After the tile is pasted, clean the surface of the tile and the gap, dry and dust-free, and then fill it with this product.

2. Use hard objects to open aluminum bottles.

3. Screw the nozzle on the mouth of the aluminum bottle.

4. Cut the nozzle into a 45-degree angle along the concave and convex top of the nozzle with a knife, and the width of the nozzle is slightly smaller than the brick joint.

5. Pull the bottom pull ring of the sewing agent. Load the sewing agent into the glue gun, and use the glue gun to evenly inject the material into the brick joint.

6. Grind the material flat with your fingers or scraper.

7. Use a wet sponge to clean up the excess material on the surface of the porcelain slag wheel brick.

8. After the construction is completed, the surface is cured within two hours, and it can be used normally after two days.

The above content is the introduction of the methods and precautions of ceramic tile joints brought to you this time for your reference. I believe that after reading this article, you will also have a certain understanding of how to do beautiful sewing, and hope to provide some help to the owners who are carrying out beautiful sewing construction.

The sewing method is as follows:

1. Slitting. It is to clean up the original crevice stains. During the decoration process, when the sewing is done again, all kinds of gaps are filled with stains, and the sewing must be cleaned before the sewing.

The depth should be kept at least about 5 mm, and it is easiest to fall off in the later stage if it is too shallow. It is also possible to achieve the depth of the thickness of the tile, so that it is a little more expensive material, but it is stronger.

2. Clean the gaps.

The cleaning here is different from the opening of the seam, use a high-power vacuum cleaner to thoroughly absorb the dirt and dust in the crevices, if there are oil or water stains, you can use a clean and bright linen cloth to clean them, little by little to ensure that the crevices are completely clean. The purpose is to ensure the firmness of the sewing paste and the longevity of use.

3. Caulking. Strictly follow the instructions for use, and then use the tools provided by the merchant to caulk. It should not be too fast, when you do it yourself, you should have enough time, try to be as slow as possible, and do it carefully, otherwise it will be too ugly in the later stage, and if you want to clear it and ask someone to do it, there is no chance.

The hardness of porcelain grout is higher than that of cement, and it is cleaned later unless the tile is smashed.

4. Compacting the gaps.

After the porcelain seam is filled, it is necessary to use the edge ball for compaction operation, the purpose is to ensure that the porcelain seam is strong and the surface is smooth and tidy. It is best to do it in a short time, depending on the weather conditions.

5. Clean up the offcuts.

After compacting the porcelain joint, there will be extruded residual material on both sides of the gap, and after a period of solidification, it needs to be cleaned with a shovel, and care should not be used to damage the gap that has been done with the imitation key.

6. Review the effect.

After cleaning up the excess remaining materials, carefully inspect each gap to ensure that there are no flaws, no omissions, and find rough or uneven potholes, even if they are repaired and rectified.

7. Repair defects and omissions.

After the inspection is completed, all the marked problems should be repaired at one time, and no omissions or rough places will be eliminated.

8. Clean thoroughly.

After all the repair work is done, thoroughly clean the ground to ensure that the floor is clean and tidy

Beauty joints can not only fill the gaps in the tiles, but also increase the aesthetics of the interior. The specific operation method of beauty sewing is as follows:

First of all, before making beautiful joints, you need to clean the gaps of the tiles to ensure that there are no impurities. The primer is then started with caulk, and the grooves are pressed out with a caulking cone. Then apply the masking paper, this step is mainly to prevent the masking agent from sticking to the surface of the tile.

Hong let this evenly squeeze the sewing agent into the gap and seal it tightly with sewing steel balls. Finally, tear off the paper at the back to remove the excess sewing agent.

After making the sewings, all the gaps are filled, so there is no more dirt and bacteria can be reduced. In addition, the adhesive of the joint is super strong, which can ensure that the tiles are clean and will not fall off.

Precautions for beauty sewing:

1. The conditions for caulking should be met.

The width of the tile is generally reserved between the width of millimeters, the depth is between 5 millimeters, if there is floor heating, the depth of the gap in the construction must ensure that the thickness of the glue layer can not be less than 2 mm, in addition to the decoration owners also have a point to pay attention to, in the balcony can not use oily epoxy resin sewing agent, expansion joints must not use reactive epoxy sewing agent, which will bring more trouble to the later stage.

2. Clean up.

Before construction, if the gaps in the tiles are not cleaned, the construction effect will be affected during construction, such as blistering and discoloration and other problems, so it is necessary to try to clean the stains in the gaps before making beautiful joints.

The operation method of beauty sewing is as follows:

1. Prepare tools such as sewing agent, masking paper and wallpaper knife.

2. Clean the gaps in the tiles, which can be cleaned with a flat-nosed screwdriver. After cleaning the gap, fill the gap with mortar, leaving a depth of about 2mm.

3. According to the size of the tile gap, cut the glue head with a wallpaper knife and assemble the glue gun. Fill the tile grout into the glue gun, and the first 15-30cm glue in the hose should be discarded.

4. Paste masking paper on the edge of the tile gap for easy cleaning. Gently squeeze the grout into the gap between the tiles.

Note that after pressing the seam, if the excess sewing agent on the masking paper is too obvious, it should be cleaned with a scraper board in time to prevent the sewing agent from swimming and not being cleaned.

The operation steps of beauty sewing: gap treatment, pasting masking paper, installing glue gun, and sewing agent.

1. Gap treatment

Before cleaning the gaps in the tiles, we can use a vacuum cleaner to remove the dust from the surface of the tiles. Then put the cleaning cone into the gap of the tile and push it forward to clear the groove of about 3 mm.

The joint cleaning tools such as the cleaning cone are relatively sharp, and we should pay attention not to touch the edge of the tile during construction, so as not to cause the problem of porcelain breaking. Next, we use a brush, sponge, etc., to clean the gaps. Finally, we stuff paper towels into the gaps of the tiles, and if the paper towels are wet, you can use tools such as a hair dryer to dry the gaps in the tiles.

2. Paste masking paper.

Stick masking paper along the edge of the tile gaps, be careful when pasting masking paper, and don't let the masking paper cover part of the tile gaps. The masking paper at the intersection of the tiles can be cut with a wallpaper knife.

3. Install the glue gun

According to the width of the tile gap, we use a utility knife to cut a bevel on the discharge pipe. Then poke open the sealing port on the beauty sewing hose and install the discharge port on the beauty sewing hose. Then put your hand against the handle of the glue gun and pull the lever back into the sewing hose.

4. Beat the sewing agent

We first punch 15-30 cm of sewing glue on white paper, because when we first use it, the glue will be mixed unevenly. Next, aim the glue gun at the gap in the tile and apply the glue evenly from top to bottom and from left to right.

Usually, after the sewing glue is hit to 2 meters, the discharge nozzle should be blocked with a toothpick, etc., and then the caulking rod should be used to press the joint, and the sewing glue that overflows to the tile should be wiped clean with a damp cloth in time. After the sewing construction is completed, we can tear off the masking paper.