How to shovel off the sewing agent when it is dry, and how long does it take to shovel the edge of t

How to shovel off the sewing agent is as follows:1. If the type of sewing agent is different, the method of eradication will be different. Among them, the one-component beauty joint agent is water-based, and the adhesion is generally not strong, so it will be easier to shovel off, as long as the tile gap position is scraped continuously with a utility knife, it can generally be easily shoveled off.

2. The hardness of the two-component sewing agent will be higher, so it will be more difficult to clean up, if you want to clean it, you need to use a hair dryer with power in two kilowatt operation to continuously blow the position of the tile gap, until the sewing agent becomes soft, and then use a shovel or utility knife to remove the sewing agent.

3. If you want to clean the two-component sewing agent, then it is best to use a hair dryer with higher power, if the power is too low, it will be difficult to reach the temperature that softens the sewing agent, and if you use the hair dryer for a long time, the hair dryer may be damaged. In order to avoid hot air burns on your hands, it is recommended that you wear gloves.

There are two types of sewing agents: one-component and two-component.

The one-component is water-based, which is relatively easy to clean, and its adhesion is not strong, while the adhesion of the two-component sewing agent is more reliable.

The one-component sewing agent is directly cleaned with a utility knife, and it can be easily scraped and shoveled directly.

The two-component can be blown with a hot hair dryer with a power of about two kilowatts for a period of time to soften the sewing agent in the porcelain seam, and then be careful.

Use a shovel to remove (use a shovel with a blade). Otherwise, you'll be shoveling the tiles.

When the beauty sewing agent is dry, please don't be anxious, because if you accidentally break the tile, you will feel distressed, you can use a hair dryer to make the porcelain crystal glue soft, and then carefully remove it.

It's best to use a hair dryer to blow hot before shoveling, otherwise the tile will jump, and I will suffer.

Shovel off with a shovel with a blade.

Generally, on tiles with smooth surfaces, the grout waits for 48 to 72 hours, and after the grout is completely cured, you can use a rubber spatula to remove the excess grout on the surface of the tile.

At this time, the sewing agent has been completely cured, and the sewing agent is very hard, so it can be cleaned at one time. If the seam is not completely cured, when shoveling the glue, the tile will leave a certain amount of gel, which is more troublesome to deal with.

The time taken to shove the sewing agent is affected by many factors, such as temperature, humidity, sewing agent formula design, etc. Generally speaking. Maintained at a temperature of about 25 degrees Celsius and a normal humidity of about 70%, Harvest Jie Zhen porcelain glue can be dried for 2-3 hours to achieve the strength of shoveling edge without sticking to your hands.

Lay the sewing agent, press the sewing well, wait for 2 to 4 hours to shovel off the edge of the sewing agent.

The method of shoveling off the beauty joint: use a utility knife to continuously scrape the position of the tile gap; Hot blow with a hair dryer and shovel after shoveling.

Depending on the type of sewing agent, the method of removal will be different. Among them, the one-component beauty seam high rent agent is water-based, and the adhesion is generally not strong, so it will be easier to shovel off, as long as you use a utility knife to scrape off the tile gaps, you can generally easily shovel off.

If you want to clean it, you need to use a hair dryer with a power of two kilowatts to continuously blow the gap between the tiles until the seam becomes soft, and then use a shovel or utility knife to remove the seam.

Precautions for the construction of beautiful seams

1. Before the construction of the beautiful seam, the dust, cement slag and dirt in the tile gap should be cleaned up, and the surface of the tile should be wiped clean, and a masking paper should be pasted on both sides of the tile gap.

2. When carrying out the construction of beautiful seams, you must not use sharp objects to poke the gap position of the tile, and you must not use a strong acid and alkali solution to wipe the surface of the tile, otherwise it will be easy to damage the tile.

3. After the construction of the beauty joint agent is completed, the excess beauty joint around the tile gap should be wiped clean with a sponge, and the masking paper pasted on both sides of the tile gap should be torn off.

You can use a sewing remover, which requires a sponge, a rag and gloves. Here's how:

1. First of all, bring gloves to open the nozzle and install the thin tube, and shake the spray evenly.

2. Spray at an angle of 45° on the place where there is a sewing agent, and wait for 1-10 minutes after spraying the collapsed mountain.

3. Brush the ground sprayed with the rough side of the scouring pad, and you can see that a large amount of sewing agent has been brushed off.

4. Then wipe the remaining stains on the ground with a rag.

5. The tile floor cleaned with the sewing agent is shown in the figure below, and the effect is remarkable.

Summary. Hello! Dear, the cleaning method is as follows:

1. The one-component sewing agent can be cleaned directly with a utility knife, and it can be easily scraped and shoveled directly. The two-component can be blown with a hot hair dryer with a power of about 2 kilowatts for a period of time to soften the sewing agent in the porcelain joint, and then carefully shoveled away with a shovel (use a shovel with a blade). Otherwise, you'll be shoveling the tiles.

2. You can blow it with a hair dryer first to make the force porcelain crystal glue soft, and then carefully remove it. 3. It's okay to shovel gently, but don't damage the sewing agent in the seam. It is also possible to remove excess sewing agent with a rag.

The sewing agent is dry. The more stubborn kind, the thin one is not easy to shovel, how to clean it. Thank you.

Hello! Dear, the cleaning method of the shovel is as follows: 1. The one-component sewing agent can be cleaned directly with a utility knife, and it can be easily scraped and shoveled directly.

The two-component can be blown with a hot hair dryer with a power of about 2 kilowatts for a period of time to soften the sewing agent in the porcelain joint, and then carefully shoveled away with a shovel (use a shovel with a blade). Otherwise, you'll be shoveling the tiles. 2. You can blow it with a hair dryer first to make the force porcelain crystal glue soft, and then carefully remove it.

3. It's okay to shovel gently, but don't damage the sewing agent in the seam. It is also possible to remove excess sewing agent with a rag.

4. You can use an electric hair dryer to heat the seam on the tile, and then soften it, and then wipe it off little by little with a sponge or rag. Do not use a spatula to remove the grout, which is easy to scratch the tile and easily damage the tile glaze. 5. Buy the sewing agent cleaner online, spray the cleaning agent on the dried sewing agent, and wipe it off with a rag after it is decomposed.

For tiles with smooth surfaces, if there is any residual seam agent, you can use a grabbing knife or a wallpaper blade to tilt and steal it with slight force; For matte and three-dimensional tiles, it will be relatively laborious to use a knife to deal with it, and it is not recommended to use a knife to deal with it for the safety of the tile.

1.If you find that there are still some remaining materials on the surface of the tile after the beauty joint agent has solidified, don't worry, it can generally be removed. First of all, let's analyze the properties of the sewing agent, the cured sewing agent has relatively stable physical properties, and a variety of commonly used solvents cannot dissolve it.

2.The thinner can be dissolved to a certain extent, but the process is relatively slow, and a certain amount of external force is required to assist in wiping in practice. However, thinner is a toxic organic solvent that can be harmful to health if exposed to it, so it is best to use it as little as possible, and keep ventilation after treatment to speed up the volatilization of the material.

3.Let's talk about the situation of floor tiles, generally speaking, there are three kinds of tile surfaces: smooth surface, frosted surface, and three-dimensional surface.

For tiles with smooth surfaces, if there is any residual seam agent, you can use a grabbing knife or a wallpaper blade to tilt and steal it with slight force; For matte and three-dimensional tiles, it will be relatively laborious to use a knife to deal with it, and it is not recommended to use a knife to deal with it for the safety of the tile.

4.It is recommended to solve the problem at the source as much as possible, that is, before and after the construction of the joint, wipe the brick surface on both sides of the brick joint with a wet sponge before the joint to keep it moist to facilitate the later wiping; After seaming, it must be wiped with a clean semi-dry wet sponge in accordance with the requirements of the specification, and the water used to clean the sponge should be replaced in time.

If it is an antique brick, it is very troublesome, and there is even no way, this kind of tile is best to use masking paper or water porcelain sewing agent before construction.

It can be washed off directly with water.

If it is a polished tile or glazed brick, you can scrape it off directly with a knife or shovel.

I believe that many friends have had the phenomenon of leaking seams at home, usually everyone will choose to use the sewing agent, but after the sewing agent is dry, if there are some inappropriate places, we will get rid of it, but do you know how to get rid of the sewing agent after it dries?

How can I get rid of the sewing agent after it is dry?

1. A hot air blower can be used. Because when the sewing agent dries, the sewing agent will become very hard. If the sewing agent is in the gap of the tile, it should be blown soft with a heat gun, and after the sewing agent becomes soft, use a sewing knife to scrape out the sewing agent. Be careful with this step and be careful not to damage the tiles.

2. If you accidentally stick the sewing agent on your hands and it has dried, there are two ways to clean it. One is alcohol or diluted white vinegar, which can be washed slowly to decompose the sewing agent. Don't do it by force, or it will easily hurt our hands.

3. If the sewing agent sticks to the clothes and has dried, we can use banana water to clean it at this time. However, banana water is corrosive and has a taste. After the sewing agent is washed off, it is best to use laundry detergent to wash it several times to remove the odor.

What are the precautions for using sewing agents?

When using a sewing agent, it is best not to poke the gap with a sharp object, and do not use an item with strong acidity. After use, we should pay attention to the application time of the sewing agent to ensure that it is before the furniture enters the site. Before the application of the beautifying sealant, it is necessary to use caulk as a base to enhance the effect.