In the future, if the country does not allow charcoal, what will be used for copper smelting and sil

Mechanism charcoal machine equipment is to take mechanized means to achieve the process of raw material carbonization, in the whole process of human participation has few opportunities, which leads to the charcoal machine equipment in the production of charcoal resulting in too large charcoal ash, the use time is too short, thus reducing the mechanism of carbon market, and for customers who are familiar with the mechanism charcoal machine equipment can easily get high-quality charcoal, so as to obtain quality advantages in marketing and continue to grow. The control principle of ash content in the mechanism carbon is actually relatively simple, and Changde Taofayuan Biotechnology Co., Ltd. conducts the following analysis in order to benefit customers. 1. In the process of making rods, the internal structure caused by the insufficient density of the rods is loose, which increases the burning area of charcoal in the carbonization process, resulting in excessive carbonization and excessive ash content.

2. The influence of raw materials: in the original....

The state is mainly based on environmental protection to reduce or even eliminate the production of raw charcoal, but in advocating the reproduction and reuse of biomass waste raw materials such as straw carbon, like the current raw charcoal is not allowed to be exported, only mechanical carbon and bamboo charcoal (bamboo product scraps) can be exported. This shows that the country is still advocating in this regard, but the current carbon equipment is not environmentally friendly enough, to be developed, rest assured that the country and society are still in the initial stage of dealing with straw, and will develop well! I am developing new energy-saving and environmentally friendly carbon production equipment, and I hope to contribute to society!

Won't not be produced. Reducing charcoal production is to protect trees. However, charcoal, as an important chemical, will not be unproduced.

Hello, it is a pleasure to serve you and give you the following answer: Different. The charcoal used for copper smelting and silicon smelting is different because they have different melting points.

The temperature of charcoal required for copper smelting is higher than that required for silicon. Reason: The charcoal temperature required for copper smelting is higher than that required for silicon smelting, because the melting point of copper is higher than that of silicon.

Solution: To smelt copper and silicon, different charcoal must be used to meet their respective melting point requirements. Steps:

1.First of all, prepare the charcoal required for copper smelting, which requires a higher temperature than the charcoal required for silicon smelting. 2.

Then, the copper powder is put into the furnace and the charcoal is placed in the furnace at a temperature that reaches the melting point of the copper so that the copper powder can be melted at a loss. 3.Finally, the molten copper is poured into a mold to form a copper block.

Personal tip: When smelting copper and silicon, be sure to use different charcoal to meet their respective melting point requirements to avoid problems.

Hello dear, Liang Zheng. <>

Copper smelting does not have to be made of raw charcoal. Fuels such as coal, oil charcoal, and coal can also be used. Copper smelting can use reducing agents such as charcoal, carbon monoxide, or hydrogen, where charcoal is less costly.

In nature, copper is mainly found in copper ore in the key bundle. Chalcopyrite and malachite contain copper, which is burned or decomposed at high temperatures to form copper oxide. Reducing agents such as charcoal, carbon monoxide or hydrogen can seize the oxygen in copper oxide and reduce it to metallic copper under high temperature conditions.

The premise of using charcoal depends on the following factors:

1) If you can obtain a reducing agent with a higher specific resistance, such as blue charcoal with a carbon content of more than 85% or washed coal with an ash content of less than 3%, then you can not use charcoal as the main reducing agent.

2) If you get charcoal on average** less than 1500 yuan ton, it is available.

3) If the sum of K and Na in your silica composition is lower than that, and the mechanical properties are poor, it is available.

4) If your electric furnace is relatively deep and wide, it can be used.

5) If your product is 553 does not blow oxygen, you should use it as little as possible, otherwise you will lose money.

6) If your furnace refining technology is OK, the standard of unit consumption is that as long as it is lower, it can be replaced by washed refined coal.

Specifically, it is ideal to make a decision based on the conditions. The result is excellent, excellent, very good, but there is no 100 points, and there is no so-called fail, only the difference between 50 steps and 100 steps.