When the computer is turned on, it gets stuck in the place with the Lenovo logo and can t get in?

1) Immediately after booting, press F8 to do not move to the advanced option appears in the let go, select "The latest correct configuration" Enter to repair, and press F8 to enter the safe mode to restore the system or reinstall the system (if the reinstallation is also dead, it is recommended to overhaul it, if you can enter the safe mode, it means that you have installed inappropriate things, and uninstall all the inappropriate things before the accident, or restore the system or reinstall it).

First soft and then hard, such problems are caused by software conflicts, inappropriate drivers, and system problems, you can restore the system in safe mode, or not reinstall the operating system, do not install software, patches, drivers, etc., and see if there is still a problem with booting? If you don't install drivers, patches, and software step by step, and find something that isn't suitable, don't install it.

2) If this is always the case, first soft and then hard, reinstall the operating system, do not install software, patches, drivers, etc., and see if there is still a problem with booting? If you don't install drivers, patches, and software step by step, don't install anything that doesn't fit (if you have any questions, please ask me).

Please note: If you restore the system or reinstall it, when installing drivers, patches, software and other things, be sure not to install the things that affect your accident this time, otherwise it will be restored or reinstalled in vain.

3) Whether there is a problem with hardware, such as hard disk, memory, graphics card, motherboard parts, etc., if it is caused by hardware problems, it is recommended to overhaul it.

1. Turn on the Lenovo computer and open the BIOS with the F2 key, and click Load Optimal Defaults directly in the exit to enter.

2. Next, a new dialog box will pop up, and you need to select yes to jump.

3. If it's okay, just press the F10 key to save and restart.

4. At this time, you will see the picture of lenevo appearing.

5. In this way, when the desktop is found to be opened normally, the requirements can be realized.

The solution to the notebook boot stuck on the Lenovo screen and unable to enter the desktop is as follows:

1. First of all, turn on the computer, press F8, and select [Safe Mode] in the boot mode interface

2. Enter the safe mode, a confirmation dialog box will pop up, and click [OK] below

3. Then, open the [Start Menu] in the lower left corner of the computer, find the [Control Panel] and click to enter:

4. Enter the control panel and click [Add or Remove Programs] below

5. In the list of installers, select the software installed before the computer is normal, and uninstall it, so that the computer will not be stuck on the welcome page and unable to enter the system when it is turned on.

Now whether it is study or work, we can't do without the computer, but recently some users have reported that their computer has been stuck in the Lenovo interface when it is turned on, and they don't know how to solve it, which affects their own use. So what I have sorted out for you today is the solution to the Lenovo interface that keeps stopping when the computer boots up.

Here's how to fix it:

1. Restart the Tab button to skip the logo screen or press the Del key continuously (F2 or other specified hotkeys for notebooks) to enter the CMOS setting interface, turn off the Full Screen Logo Show in the Advanced BIOS Features tab to see if the POST information can be displayed, and then judge that it is the problem.

The solution to the problem that the computer keeps stuck in the Lenovo interface when it turns on.

2. Press the F1 key to skip and start the computer directly, or press the Del key to enter the CMOS, then press F9 to load the predefined parameters or select the load optimized defaults or load fail-safe defaults, and then press F10 to save and exit the restart.

The solution to the problem that the computer keeps stuck in the Lenovo interface when it turns on.

3. If the original CMOS parameters are not saved or the system time in CMOS is restored to the factory time after the shutdown and power failure, then the fault may be due to the failure of the motherboard battery, and the battery needs to be replaced before the previous operation.

The solution to the problem that the computer keeps stuck in the Lenovo interface when it turns on.

4. If the above methods are invalid, it may be that the hard disk needs to be re-inserted or the hard disk due to poor connection or the hard disk master boot record is damaged, or the hard disk master boot record needs to be re-inserted, or the hard disk master boot record needs to be repaired, or the system can be reinstalled or the hard disk replaced.

Press F8 immediately after booting to the advanced options and then let go, select [Latest Correct Configuration] Enter; It is not possible to press F8 to enter the safe mode to restore the system or reinstall the system; If the reinstallation is also a crash, it is recommended to overhaul it.

can solve the problem. Press the BIOS boot button first, then we can choose the Chinese mode, click on "Advanced mode" at the bottom.

2. Click "Startup" in the BIOS menu bar, find "Wait for the F1 button to be pressed if there is an error", and select "Close" in the corresponding right option.

3. Press F10 to save, restart the computer, and the problem of staying on the motherboard logo will be solved.

What should I do if my computer keeps being stuck in the Lenovo interface?

1. First restart the computer and press the Tab button to skip the logo screen, or press the Del key continuously when booting up to enter the CMOS setting interface.

2. Turn off "Full Screen Logo Show" under "Advanced BIOS Features" to check for POST problems.

3. After that, press F1 to skip and start the computer directly, then press F9 to load the predefined parameters, select "Load Optimized Defaults", then press F10 to save and exit and restart.

4. If the original CMOS parameters are not saved after restarting, it may be that the motherboard battery has failed, repeat the above operation after replacing the battery.

5. If the above methods are invalid, you need to reseat the hard disk or repair the master boot record of the hard disk or reinstall the system, and finally consider replacing the hard disk. 

The computer can't turn on, only the icon is displayed because the key files of the system are deleted by mistake, here you can reinstall the system to solve the problem, the specific operation steps are as follows:

1. First install the system USB flash drive on the computer, then wait to enter the main menu interface of the USB flash drive installation master, select 02 to start the windows10 operating system, and press the enter key to confirm the selection.

2. After entering the U disk installation master win10pe system, the U disk installation master PE one-click installation tool will automatically open and load the win10 system ISO image file GHO installer, click to select C disk as the system installation disk, and then click the "execute" button to continue.

3. Then the message question pops up in the window, click the "Open" button to continue.

4. Wait for the win10 system ISO image file GHO installer to be released and automatically restart the computer.

5. After the computer is restarted, the system will automatically install the follow-up program, and set the relevant account parameters, until you enter the win10 application selection interface, click the "desktop" application in the lower left corner, and then you can start and run the computer's operating system normally.

1. Turn on the Lenovo computer and open the BIOS with the F2 key, and click Load Optimal Defaults directly in the exit to enter.

2. Next, a new dialog box will pop up, and you need to select yes to jump.

3. If it's okay, just press the F10 key to save and restart.

4. At this time, you will see the picture of lenevo appearing.

5. In this way, when the desktop is found to be opened normally, the requirements can be realized.