Which method is good for washing floor heat, what is physical or chemical? Which is better?

Radiant underfloor heating (geothermal) brings a touch of warmth to your home. However, with the growth of the service life of geothermal heat and the corrosion of water accumulation in geothermal pipes for many years, have you noticed its overhaul, maintenance, cleaning, and maintenance problems?

Check to see if your home's geothermal pipes are also experiencing the following:

1. The inner side of the connecting pipe wall of the manifold is yellow, green, red rust and black.

2. The indoor temperature is significantly lower than before and it is used for more than two heating periods.

1.Projectile cleaning method, working principle: compressed air as the driving force, using the launcher to launch a special projectile larger than the inner diameter of the pipeline 10-20 into the geothermal pipeline, so that it moves along the inner wall of the pipeline and rubs against the inner wall of the pipeline, and cleans the inner wall of the pipeline. It is very good in principle, but during the construction, each circuit of the water separator should be removed, and the hair dryer should be used to heat, which is easy to cause pipe breakage, water leakage, falling off, and if the geothermal pipe is seriously scaled, the projectile will be blocked in the middle and cannot get in and out, and the consequences are very serious.

2.Chemical flushing (often with chemical drugs will remove a thin layer of geothermal pipes, which will cause damage and rupture to the geothermal pipes over time.) )

3.Pulsed physical wave cleaning. (This method is best because the high-pressure airflow breaks through the impurities in the geothermal pipes.) It will not cause any harm to the tube. )

We now use a fully automatic pulse geothermal cleaning machine, the working principle is one flush, two wash:

"One flush" - clean water flushes the sewage in the pipeline, so that the free scale, biological sludge, magnesium and calcium ions in the pipeline are washed out. "Second washing" - the use of pulsed physical waves to impact and microwave vibration on the inner wall of the pipe, so that loose scale, biological sludge and other deposits peel off and remove from the pipe. It takes only 1 hour to clean a 100-square-meter house, using pulsed physical waves.

Cleaning is carried out at the water separator of each user, without disassembling the geothermal pipe joints. It avoids the pipe breakage and falling off caused by frequent pipe dismantling, and achieves a good cleaning effect without destroying the original structure of the heating equipment.

Pulses and projectiles, most people think pulses are good!

Pulse cleaning method is the most commonly used cleaning method at present.

There are currently two main methods of geothermal cleaning:

1. Pulse cleaning method: It is to use high-pressure pulse air flow into the water separator, and control each geothermal pipe by the shunt method, the high-pressure pulse air flow continuously washes the wall of the geothermal pipe, and the impurities and dirt are continuously discharged with high pressure, and the whole cleaning process has no damage to the water separator, which is the preferred geothermal cleaning method at present.

2. Sponge ball cleaning: sponge cleaning dissociates the geothermal pipe from the water separator, puts the cleaning sponge ball in the pneumatic or geothermal pipe, and then stucks the pneumatic on the geothermal pipe, and uses compressed air to eject the cleaning into the geothermal pipe, and comes out from the other end of the pipe to achieve the cleaning purpose. The cleaning effect is good, and the tube can be restored to its original color.

The disadvantage is that the efficiency of unpacking is relatively low, and it is easy to get stuck when there are joints and bends in the geothermal pipe.

3. Reagent cleaning: It should be said that the cleaning effect of reagent cleaning is very good, but it is rarely used because it is easy to corrode and aging geothermal pipes and system components and pollute emissions.

Additional information: Geothermal cleaning intervals.

Geothermal cleaning can be cleaned all year round, the best time is the early stage of the heating process every year, due to the different water quality of each lot for more than two years have not been cleaned customers at any time to pay attention to cleaning to prevent blockage, winter heating customers should pay attention to drainage and anti-freezing.

The first method is pulse, which is costly and does not work well.

The second type is cleaned with pneumatic firing sponge bullets and has high cleaning efficiency.

Generally speaking, pulse geothermal cleaning is more thorough and will not harm the pipes. Potion cleaning hurts pipes, and bullet cleaning easily jams pipes.

Pulse cleaning, chemical cleaning, all need to be consumed repeatedly. Now you don't have to manually clean the floor heat. Install pre-filter--- Jiadi heating filter, automatic work without manual operation, generate low-frequency pulses several times a day, waste water is directly discharged back to central heating, three No. 5 batteries drive, after installation, the geothermal heat never needs to be cleaned, the room temperature is increased by 3 degrees, safe and environmentally friendly.

There are more and more unmanaged geothermal cleaning teams, and they think that consumers can't do anything about them, because they know where your house is, on the contrary, they don't know what his name is, so they are unscrupulous, they don't want to figure out anything, they just want to start first and then talk about money, no matter how good or bad they do, they are full of asking prices, and if you don't give it, they will scare you, because you don't know his identity, and those with big shoulders and round waists will use this to eat, so we consumers must ask for their ID cards before they enter the house, and it is best to have a work permit.

Geothermal cleaning ejection is good, you can consult the Wantong 86652516

Underfloor Heating Cleaning Methods After the geothermal system enters the real home life, there will be problems with pipe cleaning and descaling. If there is no maintenance and cleaning of the geothermal heating system. In winter, when the neighbors are heating, the home cannot achieve a warm and comfortable environment, which not only affects the normal use of floor heating, but also causes a waste of energy.

Collected some geothermal cleaning methods, let's take a look.

1. Jet cleaning with cleaning agent.

This cleaning process is currently the mainstream cleaning method in the world. It has the characteristics of energy saving, high efficiency and environmental protection. The cleaning agent prepared with high-quality environmental protection agent and corrosion inhibitor can fully dissolve the slime attached to the pipe wall, which will not cause pollution to the environment, and will not corrode the heated metal pipe fittings and be thoroughly cleaned.

Due to the corrosion inhibitor contained in the cleaning agent, a protective film will be formed on the inner surface of the metal parts of the geothermal heating pipe after cleaning, which can effectively prevent the re-formation of scaling and corrosion points.

In addition, this construction process requires the use of a dedicated high-flow jet cleaner. These professionally designed underfloor heating duct washers have a two-way cleaning function to clean dirt at the pipe interface. The process also features a cleaning mode.

The geothermal heater cleaner is connected to the heat source interface. By controlling the inlet valve and the return valve of the manifold box, the pipes controlled by each group of the manifold box are cleaned respectively, and the operation space is large and the work efficiency is high. After cleaning, there is no need to inject liquid into the underfloor heating system for exhaust gas.

This is an international mainstream cleaning process. Its advantages are: thorough cleaning, full dissolution of slime attached to the pipe wall, high-quality food-grade raw materials will not cause corrosion to the floor heating pipe.

2. Projectile physical cleaning.

This cleaning method uses friction between the cleaning drum and the pipe wall to remove the mucus that adheres to the pipe wall. The advantage of the utility model is that the dirt in the pipeline can be cleaned without any chemical cleaning agent. The disadvantage is that the geothermal heating pipes have to be removed.

If there are joints in the underground pipeline, the construction is very inconvenient, and it is easy to make the cleaning cylinder stuck in the pipeline, and the water collector and boiler cannot be cleaned. In addition, it may also cause secondary damage to the original manifold, floor heating pipe interface and other related connection parts, reducing the service life of the floor heating system.

3. Pulse wave physical cleaning.

The advantages of this cleaning method are the same as those of projectile physical cleaning, which does not require chemical cleaning agents and does not require the removal of geothermal heating tubes.

Its unique cleaning process cleans the main pipes and valves of the floor heating water collector to avoid long-term fouling and clogging of the valves. The disadvantage of this cleaning method is that the construction is limited by space, especially the floor heating manifold of some users is installed in a hidden place, and the two ends of the manifold are too close to the wall, and the cleaning difficulty is larger, and pulse cleaning takes a long time. After the cleaning is completed, it is necessary to inject and drain the liquid, which increases the labor cost and construction time of the workers.

There are currently two main methods of geothermal cleaning:

The bullet cleaning method is to remove the geothermal pipes respectively, place the sponge ball in the geothermal pipe, and push the sponge ball into the geothermal tube by high pressure to push out the impurities on the inner wall of the pipe, the disadvantage of this method is that the sponge ball is easy to get stuck in the tube, and the sponge ball cannot be completely pushed out when there is too much silt in the pipe.

The pulse cleaning method is to use high-pressure pulse air flow into the water separator, and control each geothermal pipe by the shunt method, the high-pressure pulse air flow continuously washes the wall of the geothermal pipe, and the impurities and dirt are continuously discharged with the high pressure, and the whole cleaning process has no damage to the water separator, which is the preferred geothermal cleaning method at present.

For home decoration, many people focus on geothermal heat, because its presence not only brings us warmth, but also does not affect the beauty of the space. So, for geothermal energy, what should we pay attention to when using? And which cleaning method is better?

Geothermal renderings.

1. Rinse with water.

The advantages of this method are: convenient, non-corrosive, and will not cause damage to geothermal heat.

The disadvantage is that the cleaning is not thorough enough, and it is a non-professional cleaning.

2. Chemical cleaning.

The advantage of this method is that it is cleaner.

The disadvantage is that due to its corrosiveness, it will cause damage to the inner wall of the pipe network during cleaning, which directly affects the secondary cleaning effect of the pipeline and artificially reduces the life of the pipe network.

Geothermal renderings.

3. Physical projectile cleaning and cleaning.

The advantage of this method is that the cleaning time is shorter.

The disadvantage is: during the construction, each circuit of the water separator should be removed, and the hair dryer should be used to heat, which is easy to cause pipe breakage and water leakage, and the geothermal pipe will be fouled seriously and the projectile will be blocked in the middle, which will cause very serious consequences.

4. High-pressure pulse cleaning.

The advantage of this method is that without any agent, the cleaning of imitation dust is carried out at the water separator of each user, and there is no need to dismantle the geothermal pipes on the street. It avoids the pipe fracture caused by frequent pipe dismantling, and achieves a good cleaning effect without destroying the original structure of the heating equipment.

Geothermal renderings.

The disadvantage is that the return to the mu is longer during cleaning.

Well, the above is a good introduction to which method of cleaning geothermal energy, do you have a clear understanding of these contents? If you want to know more about the renovation, please stay tuned.