There is a leak in the area, so will it affect the drain of the toilet?

Hello, there are many possibilities for your situation, it may be caused by a blocked drain, or a leaky toilet drain will also cause the drain to not be strong. It is recommended to find a master to dismantle the toilet bowl and take a look. Toilets that fall into disrepair can lead to a lot of problems.

The toilet begins to leak after flushing, and there is a big leakage sound, such a situation occurs because the toilet outlet valve is damaged, and the toilet outlet valve needs to be replaced, the specific operation steps are as follows:

1. Take the toilet lid off.

2. Find the toilet drain valve.

3. Pinch the outlet valve and shake it from side to side.

4. You can remove the outlet valve.

5. Install the new one.

6. Close the toilet lid and the operation is completed.

The toilet began to leak after flushing, and there was a loud leaking sound, what was going on.

Hello! The reasons for the leakage of the toilet are: the first possibility is that the toilet sewage hole (the hole connected with the sewage pipe) is not flushed wide and the installation flange ring is not widened or the installation is incorrect, and the air leaks due to opening, which can be solved by re-installing it; Second possibility:

The toilet is damaged above the "S" bend or the "S" bend seals the water partially leaking, resulting in the sewer not being isolated by the water seal; 3.The third possibility: check whether there is enough water (water seal) in the bathroom at ordinary times, and the outlet of the "water trap" should be closed; Suggested Scenario:

1. Buy a bucket of porcelain white or transparent mildew-proof glass glue; 2. Clean the water around and around the toilet base, otherwise the glue is not easy to bond; 3. The toilet base should be sealed around the base (the glass glue can be used only after drying).

It is likely that there is an air leak around the base of the toilet, because the perimeter is not tightly closed, so when the toilet is drained, the air pressure decreases and the air is inhaled from the periphery. Suggested treatment plan: 1. Buy a bucket of porcelain white or transparent mildew-proof glass glue; 2. Clean the surrounding area of the toilet base, and the surrounding water should also be cleaned, otherwise the glue is not easy to bond; 3. The perimeter of the toilet base is glued and closed (the toilet can only be used after the glass glue is dry).

The toilet begins to leak after flushing, and there is a big leakage sound, such a situation occurs because the toilet outlet valve is damaged, and the toilet outlet valve needs to be replaced, the specific operation steps are as follows:

1. Take the toilet lid off.

2. Find the toilet drain valve.

3. Pinch the outlet valve and shake it from side to side.

4. You can remove the outlet valve.

5. Install the new one.

6. Close the toilet lid and the operation is completed.

What you hear is not the sound of air leakage, it is the sound of the float valve opening to the water tank, as the height of the float valve float increases, the sound will become smaller and smaller, and finally the tank is full, the float valve is closed, and the sound is gone.

It is the sound of air flow when the water flows down rapidly, which is normal.

It should be the sound of the float valve opening entering the tank.

No, the sound of water entering the water.

Hehe, hello, what you hear is not the sound of air leakage, it is the sound of the float valve opening to the water tank, as the height of the float valve float increases, the sound will become smaller and smaller, and finally the tank is full, the float valve is closed, and the sound is gone.

There can be a problem with the toilet, you can ask the toilet repairman to come and take a look.

The floor drain is anti-gas after the toilet flushing on the first floor! Hello, I am happy to answer for you<> The floor drain after flushing the toilet on the first floor is because the toilet sewer pipe is laid and the root of the floor drain is too close, and it is best to dredge the U-bend of the floor drain. Reduced air resistance 1

Use toilet cleaner as a dredging agent: pour an appropriate amount of toilet cleaner into the toilet every once in a while, close the toilet lid and let it sit for a while, and then rinse it with water to keep the toilet unobstructed. 2. How to block the overflow of floor drains:

Find a plastic bag that does not leak, fill it with an appropriate amount of water, remove the grate on the floor drain, and put the plastic containing water on the floor drain mouth. 3. Even if the indoor toilet is flushed cleanly, it will often leave a smell, as long as a small cup of balsamic vinegar is placed in the toilet, the smell will disappear. Swap and never once a week.

4. Dry the residual tea leaves and put them in the toilet or ditch to smoke them to eliminate the stench. Flush toilet gas may be caused by the lack of water in the trap, or too little water to seal all the drains, resulting in odors. Look downstream to see if your sewer vents are blocked (on the roof) or if someone pours a lot of water to create a vacuum that sucks the water out of your trap.

Have you not lived in your home for a long time or have not used the toilet for a long time, and the water in the trap has evaporated? Another is the quality of the toilet itself, the water storage is too small, and it is easy to leak. Hope mine can help you <>

Do you have any other questions?

Summary. Hello dear, no, the toilet drain gasket is broken, and it will only leak to your own floor. But if it is bad for a long time, there will be too much water in the house, and it will leak downstairs, so the waterproofing at home must be done.

The specific treatment methods are: first, we can buy some sealant back, and then seal the sewer pipe around it with sealant, and after it dries, we can solve the phenomenon that the toilet sewer pipe leaks first; Second, we can put a thick layer of sealant on the toilet base to seal it, and wait for the glue to dry to solve this problem.

Hello dear, no, the seal of the toilet Yunfeng drain is broken, and it will only leak to your own floor. But if the bad time is long, there will be too much water in the house, and it will leak downstairs, so the waterproofing of the home must be done. The specific handling method is as follows:

First, we can buy some sealant back, and then seal the sewer pipe around it with sealant, and after it dries, we can solve the phenomenon that the toilet sewer pipe leaks first; Second, we can put a thick layer of sealant on the toilet base to seal it, and wait for the glue to dry to solve this problem.

The steps of installing the gasket are as follows: 1. First wipe the sewage outlet at the bottom of the toilet and the drain around the ground, and ensure that there is no water attached during the installation process, so as not to affect the adhesion of silica gel and glass glue. 2. After the preparation for toilet installation is completed, then put some silicone on the toilet drain and then stick the flat side of the toilet lightly, tear off the toilet oiled paper, move the toilet, put the convex side of the toilet down in the center of the drain and press it tightly.

3. Gently shake the toilet back and forth to loosen the wax seal and glass. Carefully grasp the potty and not the tank. If you grip the tank, you may break or crack the connection between the tank and the potty.

Remove the old wax seal from the two joint surfaces. 4. Disassemble the new sealing ring (which can be bought at the hardware store), make its round side face up, and put it on the sealing ring on the ground, so that it is just above the opening. Make sure both screws are in place.

Lift the toilet vertically, place it on the seal and wax seal, and keep the toilet as level as possible. 5. Reconnect the water supply pipe. Open the water valve to fill the tank.

Flush and check for leaks. If it is necessary to put glass glue between the gap between the bedpan and the floor. Succeed with flying colors!

Well, it's not very difficult, remember to wash your hands with hand sanitizer.

Generally, there will be no air leakage, and the specific treatment method of the flush toilet is blocked;

1. Buy some caustic soda, boil water to melt the caustic soda, and pour it into the toilet.

2. Use an appropriate amount of oxalic acid (usually you can also use oxalic acid to clean the toilet, just neutralize it with urine alkali to make the toilet unblocked).

3. The old-fashioned mop, fill the toilet with half of the water, and then press the hole a few times with the mop, move quickly, and rely on pressure to get it through.

It won't leak, the air outlet is useless, the toilet is blocked, just pull it out, pass it up and down, put it on again, it's fine, I just fixed my house.

What's leaking? All of them are water-sealed and will not leak.

Absolutely.

Because there's an air outlet.