What to do if the faucet keeps dripping

Solutions for dripping water from faucets:

If the faucet keeps dripping, the first thing to do is to detect the faucet malfunction and find out the cause of the dripping. Most faucets are old for a year or two, and the valve spools are generally worn out. Just buy one and exchange it for yourself. The specific steps are as follows:

Preparation tools: spool, faucet, small pliers.

1.Start by disassembling the faucet's switch.

2.Unscrew the screws inside, and you can see the spool.

3.Use small pliers to pull out the valve core directly.

4.Prepare a new valve core and aim it to push directly. It can be used normally after replacement. You'll never have to worry about a leaky faucet again.

The solution to the faucet dripping: If the faucet keeps dripping, the first thing to do is to detect the faucet failure and find out the cause of the dripping. Most of the faucets have been used for a year or two, and the valve core is generally worn, so you can buy one and replace it yourself.

The specific steps are as follows: Prepare the tools: spool, faucet, small pliers.

1. Disassemble the switch of the faucet first. 2. Unscrew the screws inside, and you can see the valve core. 3. Pull out the valve core directly with small pliers.

4. Prepare a new valve core, align it and push it directly, and it can be used normally after replacement, and you don't have to worry about the faucet leaking. What should I do if the amount of water in the faucet becomes smaller? If it is not moved, the amount of water is getting smaller and smaller, it may be that there is a blockage in the water pipe, and there is a filter head at the outlet of some household faucets, we can check this filter head to see if there are many water holes blocked.

We can use a movable wrench to remove the filter head, clean it and install it again.

How to keep dripping from the faucet: prepare some tools, remove the screw cap on the faucet, remove the rotating handle on the faucet, use pliers, disassemble the valve core, and assemble it together.

1. First of all, we prepare some tools. Mainly including pliers, screwdrivers, etc.

2. Remove the screw cap from the faucet. Then use a screwdriver (driver) to disassemble.

3. Then we remove the swivel handle on the faucet. Exposed spool combination.

4. We use pliers. Unscrew the spool.

5. Disassemble the valve core. We will see the composition of the valve core, there is a red sealing ring inside, we add a gasket to the sealing ring, it can play a good effect, if there is no gasket accessories, you can take the tire inner tube according to the size of the sealing ring, cut a round gasket, it is also possible.

6. Then combine them and assemble them together. Reinstall it and see if it still doesn't drip anymore.

What to do if the faucet is broken

The material of the faucet is becoming more and more unreliable, there are very few all-copper, and it is a zinc alloy faucet that is broken inside, which is brittle and has a large service life, and it will be broken after a few years. If you have a small hacksaw at home, cut a deep hole longitudinally in the half that is broken inside, and then use a small chisel to break it little by little.

However, this method is not easy to control the strength, with the extractor tool, you only need to insert it into the water pipe, screw it into the break clockwise, tighten it hard, loosen it counterclockwise and rotate it counterclockwise.

The faucet is turned off and has been dripping water can be solved like this:

1. Turn off the water source, then use a tool to disassemble the label above the faucet and unscrew the screws inside.

2. Remove the handle, and then turn the valve core in the direction of the faucet until the valve core is removed and set aside.

3. Remove the fixed sealing ring.

screws, and then buy a new seal to replace it.

4. Restore the faucet parts, test it, if the faucet is still leaking after closing, you need to replace the faucet with a new one, if the faucet is closed and does not leak, it means that the installation is qualified.

Tips for buying *** faucets

1. Look at the faucet spool.

The valve core is like the heart of the human heart for the faucet, which is the most critical part, so the valve core is also an important factor in determining the service life of the faucet. When purchasing, users should choose the best spool, so that the life of the faucet will be longer.

2. Look at the faucet process.

The production process of the faucet is also very critical, the faucet with a good production process, the galvanized layer on the surface is smooth and shiny, and the paint film has no color difference, and there will be no defects such as black spots and leakage plating. When purchasing, users should carefully check the surface of the faucet to ensure that it is smooth and free of defects.