What should I do if the first stitch of the computerized sewing machine does not follow the fixed ne

If the first nail grid of the computer's sewing machine really does not follow the fixed line, then it may be a problem with the motor, and the motor is reversed.

Sewing machine First of all, we check whether the needle is installed correctly, and it is best to replace it with a new needle. 2. If it still doesn't work, we then open the needle plate, turn the needle to the lowest position, and see that the hook tip is about 8mm away from the needle.

Generally, your needle is not installed correctly, the thread is not stable, if none of the above is not, you need a professional maintenance master to overhaul.

Failure analysis: The main reasons for this failure are as follows:

1. The needle stop position is too low (resulting in a relatively early thread trimming time).

2. The thread trimming time is too early.

3. The gap between moving the knife and lifting the knife is too small.

4. The knife edge on the right side of the junction point between the fixed knife and the moving knife is too long.

If the first stitch of the computer sewing machine is not according to the deposit, it may be that you did not install it when it was installed, or there is a problem, you need to consult a professional person.

There should be something wrong with your program. Recheck the program and recalibrate the position of the fixed freeze frame and try it out.

If this happens, it may be that your translator has a certain malfunction, so it is not normal, so you must repair it well.

If the first needle does not follow the nail needle, there should be no regulation or resetting.

If the first stitch of your sewing machine does not run the stitch, it is recommended that you check whether there is a traffic jam.

The computer sewing machine is the first to order the square, it's really not bad, what should Ding Zhen do? Then you can choose the first person according to its function, which is very important, and it is very important to choose the first needle.

What should I do if the style of the computer copier is lower than I really don't like to change the nail pin, I think it should be reset.

What should I do if the computer sewing machine orders the first stitch of the square and does not follow the fixed truth? In this case, you should call the mechanic in the factory to help you see what the situation is.

Hello dear, the first step: press p first - display p - number - press plus and minus signs to adjust to p-01 - press s - speed will appear - press plus and minus signs to adjust the desired speed - press s to confirm - press p - end. 02 Step 2:

Press the P button, and P1-2000 will be displayed, so that you can adjust the speed. 03 The third step: Since the control panel of the computer sewing machine is mainly the size and speed of the needle adjustment code, the exact adjustment method also depends on the brand of the sewing machine, the computer sewing machine can be adjusted on the display screen, there is a circle on it, this is the speed, you need to press it, and then press the "-" sign.

04 Step 4: First of all, we need to check whether the needle is installed correctly, in order to avoid mistakes, it is best to change to a new needle, if it still doesn't work, you can open the needle plate, turn the needle to the lowest position, so that the hook tip is about 8mm away from the needle. If it doesn't work, lift the needle left and right to see if there is a gap between the hook tip and the needle, and the center coincides.

05 Step 5: The needle is a little bent and will skip the needle, so try to change the needle, when loading the needle, it is best to move down slowly and little by little, otherwise the thread will break, for the needle used, it is necessary to determine according to the thickness of the sewing thing, the thick one should use a thick needle, and the thin one can be a thin needle.

Summary. 1.The backlash and height position of the needle and the hook are incorrect and the direction is wrong (ask the maintenance master to correct the standard on the manual.) ）

2.Needle bending (needle replacement).

3.The thickness of the needle and the sewing material are not commensurate (choose the appropriate needle [small model 9-14 for thin fabrics, large model 14-18 for thick fabrics]).

4.Bottom line tension and presser foot pressure is too weak (increases bottom line tension and presser foot pressure).

5.The needle is short and the type is not right (choose the right needle).

Computerized single-needle sewing machine skips stitches in one direction.

In the case of a graduated slip on the needle bar of the sewing machine, when the needle bar is at the lowest point, it should be confirmed that the upper engraving line of the needle bar of the sewing machine should be consistent with the lower end of the needle bar sleeve. Secondly, when the needle bar rises from the lowest point to the lower notch line of the needle bar is aligned with the lower plane of the needle shaft sleeve, the hook tip of the hook should be aligned with the center of the needle.

It is a single needle quilting machine.

1.The side gap and high and low position of the needle and the hook are not correct and the direction is wrong, be careful of this mistake (find the maintenance master to correct the standard posture on the manual.) ）2.

Needle bending (needle replacement) 3The thickness of the needle and the sewing material are not commensurate (choose the appropriate needle [small model 9-14 for thin fabrics, 14-18 for thick fabrics]) 4The bottom line tension and presser foot pressure are too weak (increasing the tension of the bottom line and the pressure of the presser foot)5

The needle is short and the type is not right (choose the right needle).

It's good to skip the needle laterally.

Hmmm, you take a look at the methods provided to you above.

Ask about custom messages].

Hello, I am happy to serve you and give you the following answers: 1. Adjustment steps: (1) Check the oil circuit of the sewing machine to ensure that the oil circuit is unblocked; (2) Check the needle of the sewing machine to make sure that the tip of the needle is not deformed; (3) Check the needle bar of the sewing machine to ensure that the tip of the needle bar is not deformed; (4) Check the needle nozzle of the sewing machine to ensure that the tip of the needle nozzle is not deformed; (5) Check the needle of the sewing machine to make sure that the tip of the needle is not deformed; (6) Check the needle of the sewing machine to ensure that the tip of the needle is not deformed; (7) Check the needle of the sewing machine to make sure that the tip of the needle is not deformed; (8) Check the needle of the sewing machine to make sure that the tip of the needle is not deformed; (9) Check the needle of the sewing machine to make sure that the tip of the needle is not deformed; (10) Check the needle of the sewing machine to make sure that the tip of the needle is not deformed; (11) Check the needle of the sewing machine to make sure that the tip of the needle is not deformed; (12) Check the needle of the sewing machine to ensure that the tip of the needle is not deformed; (13) Check the needle of the sewing machine to ensure that the tip of the needle is not deformed; (14) Check the needle of the sewing machine to ensure that the tip of the needle is not deformed; (15) Check the needle of the sewing machine to ensure that the tip of the needle is not deformed; (16) Check the needle of the sewing machine to make sure that the tip of the needle is not deformed; (17) Check the needle of the sewing machine to make sure that the needle is tipped.

What is going on with the computerized sewing machine not looking for the stop needle position, hello For your problem, I make the following solutions: There may be the following reasons for the situation that the computerized sewing machine does not find the stop needle position:1

The machine is therefore changed to a laughing barrier: the computerized sewing machine does not find the stop needle position, which may be caused by the failure of the machine, and it is necessary to find professional maintenance personnel for maintenance. 2.

Incorrect needle bar position: Incorrect needle bar position will also cause the computerized sewing machine to not find the stop needle position, and the needle bar position needs to be adjusted. 3.

Unstable sewing machine base: If the sewing machine base is unstable, it will cause the computerized sewing machine to fail to stop at the needle position, and it needs to be adjusted and ensure that the base is placed smoothly. Nucleus contains 4

When using a computerized sewing machine, in addition to the problems of the machine itself, it is also necessary to pay attention to the problems of human operation, such as too fast sewing speed or improper use of sewing needles, etc., which may affect the use of the machine. Therefore, when using a computerized sewing machine, it is necessary to read the instruction manual carefully, pay attention to safe operation, and carry out maintenance and repair in time to ensure the normal use and life of the machine.

Dear Hello Computerized sewing machine reverses needles to many needles is not the desired number of needles may be due to the following reasons:1Improper adjustment of the sewing machine resulted in a mismatch between the number of stitches selected and the number of stitches that were clearly ordered to be sutured.

2.The use of an unsuitable needle, such as when a thin needle is chosen to stitch a coarse needle cloth, may result in an increase in the number of needles. 3.

Improper adjustment of thread tension leads to inconsistent thread tightness, resulting in skipping stitches during suturing and increasing the number of stitches. 4.Damage to the bottom plate or other parts of the sewing machine, causing the needle to not pass through the material properly, resulting in repeated sewing.

The above factors may lead to the computerized sewing machine to reverse the needle to many needles that are not the desired number of needles, it is necessary to check the sewing machine adjustment, the needle used, thread tension, machine damage and other factors, and check and solve the problem one by one.

The computerized sewing machine reverses the needle to many needles that are not the desired number of needles may be due to the following reasons:1Operational error:

In the process of changing needles or adjusting the settings of the sewing machine, misoperation can cause needle reverse. 2.Incorrect needle plate position:

If the needle plate position does not match the sewing machine settings, then needle inversion will occur. 3.There is a problem with the needle bed:

If the needle bed of the sewing machine is worn out or there is a problem, it will lead to the needle being reversed. 4.The sewing machine is out of order:

If the sewing machine fails, for example with the electrical circuit or with the computer board, it can also cause the needle to be reversed. To solve this problem of clearing the bridge, you can try the following methods:1

Make sure the sewing machine is set up correctly and the needle board is positioned correctly. 2.Clean the needle bed and sewing machine to reduce friction.

Answer: 3Check the circuit and computer board of the sewing machine for faults. 4.

If the above methods do not work, then it is recommended to contact a professional sewing machine repairer Qiao Song for maintenance.