Will an automatic transmission car stall if you step on it?

The automatic transmission car will not turn off when stepping on the dead, because the automatic transmission car uses a hydraulic transmission device instead of the manual transmission mechanical clutch, so there is no clutch pedal, when the engine rotates and drips, the liquid is transferred to the torsion torch, and the wire is not enough to push the car forward, but it will not stall.

When the control feel is put into the forward gear to release the brake, the pedal can transmit the torque to increase with the increase of refueling and engine speed to push the car forward. And if you drive a manual transmission car, the fuel consumption of the car in the automatic transmission is higher than that of the manual transmission, about one liter higher, and there will be an automatic transmission, the cost is slightly higher than that of the same manual transmission car, so the advantage of the manual transmission is that it is easy to drive.

The automatic transmission will not turn off when the brakes are stepped on, but the automatic transmission car with the automatic start-stop function of the engine will turn off when the brakes are stepped on, and the engine will automatically turn off when the brakes are temporarily stopped during driving, but the engine will automatically start when the pedal is stepped on from the start. And the automatic transmission car must slow down in the process of high-speed driving, if you step on the brakes directly, as long as you don't step on the end will not turn off, but when you slow down and stop, it is best to take off the gear, and then stop steadily, and the car will not turn off, there is no harm to the car, do not step on the brakes without gearing, easy to stall and destroy the car.

The automatic transmission will turn off when you step on it, especially the car with a one-button start-stop function, I hope it can help you, help me pay attention to it, thank you.

An automatic car usually brakes with one foot on the brakes, and he will not turn off. But the manual transmission is not good, if you apply the brakes, he will stall.

Hello, this is the automatic start-stop function of the vehicle is enabled, the engine stalls when the brake is pressed, and it will start when the brake is released. You can look for the auto-start-stop button on your car to stop it! The button logo is as follows:

Hello, I am your exclusive technician, attentive, careful, dedicated to answering your car questions, for you to find the corresponding problem solutions and solutions! This is the intelligent start-stop function, and it is a normal phenomenon to come to the car, no problem.

The function of the fuel-saving design of the car, when the car is stopped at the red light, in order to prevent fuel consumption, the engine stop function is specially set to make the fuel consumption of the whole vehicle close to 0, and the traffic light is over, release the brake, and the car can start to drive instantly! When parking, the automatic start and stop work, you unfasten the seat belt or open the door, this situation will occur, the engine will really turn off, you need to start again! Don't wonder why the engine is turned off, it's a feature that's set up specifically for safety!

The automatic start-stop system starts to work, so as to control the vehicle to shut down, when the vehicle gear is in D gear, and release the brake, the vehicle driving computer sends a signal to the starter, and then quickly ignites, this whole system, the requirements for the starter and the battery are very high, the starter needs to work frequently, and the battery needs to be charged and discharged frequently. The automatic start-stop system requires the use of a powerful starter and requires a high level of battery. Vehicles with automatic start-stop require frequent and repeated use of the starter, and compared to conventional vehicles, the increase in starting frequency means a decrease in service life, so the starter of vehicles equipped with automatic start-stop function is specially designed to cope with such situations.

If you don't step on the brake, you can't start, you can try it, don't step on the brake and press the one-button start button, it will only enter the power-on state, the dashboard, the large screen are lit up, but the engine does not work, when you step on the brake and then press the start button, it will run. The key to start the car, starting the car not only needs to step on the brakes, gear.

It also cannot be located in the drive gear.

d r) Clear. If you don't press the brakes, and the gear is not in P or N, the engine will not respond to your start request, and pressing the start button can only enter the ACC fully energized state.

Brake, the gear is not on the N gear, P gear, and the ignition can't be hit. Whether you are used to it or not, it is mandatory for us to apply the brakes. Why do manufacturers do this?

Because this is a must-do, in order to be afraid that some people will not do it, he adds some mandatory settings. Hang in R or D gear.

Although the car is not set to brake, but because the engine power is output to the wheels after being put into R or D gear, the car will move around, and the brakes should be applied for safety.

You have to apply the brakes, otherwise the car will not respond and will not be able to start. For example, the Hyundai Tucson.

With a one-button start function, if you don't step on the brake, the car will not start, only when you step on the brake, the gear can be in P gear or N gear to start. Transmission.

There is no power transmission, the engine load is low, and the engine is a little easier to start. And if in the case of D gear or R gear, after the vehicle starts, there is a sudden forward or backward string of the excitation mold situation, for the owner, it is not conducive to driving safety.

Press to turn on and release. The control unit can only obtain the on-off or off-2 state of the switch, and the vehicle needs to use this switch to realize the ignition and start two functions, so the control unit distinguishes whether it needs to be ignited or started by the braking signal. Otherwise, there may be a situation where the transmission is notched, which is not conducive to driving.

The third situation is that when switching between the gears of P, R, and D, it is necessary to step on the brakes, which is for the sake of safety, so as to prevent the wrong gear from being hung in the process of moving forward.

Yes, you need to apply the brakes. Apply the brakes first, then shift to P, then pull up the handbrake, turn off the engine, and then lift the brakes.

The brakes should not be applied, the brakes are incorrect operations and should be re-applied. Applying the brakes is not necessary.

Automatic transmission vehicles do not need to step on the brakes when they are in the car, they only need to hang the gear in P gear and pull up the handbrake.

Automatic transmissions can be turned off without applying the brakes, and of course, people still habitually step on the brakes before various operations.

Hello, glad to help you. The automatic transmission will not turn off without stepping on the brakes, and it will only turn off when the key is turned off!

The automatic transmission cannot be turned off without stepping on the brakes, and the handbrake can be turned off only when the brake is stepped on.

Automatic transmission does not apply the brakes. He must not turn off the automatic transmission without stepping on the brakes, he must be the imitation of the ignition that will not turn off, because the party only automatically does not step on the brakes, he will definitely not turn off the fire, and prepare for the spirit because the automatic transmission only has the accelerator brake and the car is blind.

The automatic transmission can also be turned off without stepping on the brakes, as long as you hang the gear higher, if you don't step on the accelerator, it will also hold the fire out.

The automatic transmission can also be turned off if you step on the brakes.

If there is a breakdown or other problems in the automatic transmission vehicle, it will also cause the vehicle to stop and fire.

The automatic transmission cannot be turned off without stepping on the brakes, so it should be stepped on the brakes, although it is an automatic transmission, but it should also be on the brakes and clutch.

No, hope it helps, thank you!

No, you can only turn off the ignition via the start button.

When an automatic car turns off, it must apply the brakes. Normal procedure, step on the brake, hang N gear, pull the handbrake, hang P gear, turn off, release the brake.

The automatic transmission will automatically turn off when the brake is stepped on, which is not a fault, but an automatic start-stop function of the engine. If there is no automatic start-stop function, it may be caused by the brakes being too sharp. Although it is said that the gearbox will automatically downshift when you press the brakes, it will cause the car to stall because the reaction speed of the overspeed transmission is too fast to brake.

1. First check whether the brake vacuum booster system is leaking (air intake, vacuum tube, check valve, vacuum booster) and replace the problematic parts.

2. Check whether the engine is missing cylinders. Check the cause and replace the faulty part.

3. The computer detects that the throttle opening (idling, turning off the air conditioner, and the throttle opening should be less than 8 degrees) is greater than 8 degrees, cleaning the throttle, and making the basic settings.

4. Detect whether the brake light switch is normal. Replace the problematic part.

5. If it is not good, the automatic transmission should be checked.

Hello, I'm helping you sort out the answers to your questions, please wait a moment

Answer: If the automatic car steps on the brakes at low speed, it stalls, this is the throttle is dirty, and there is also a stuck phenomenon, you need to clean the throttle, you need to match after cleaning the throttle, and the question throttle has been washed.

Asking questions is learning.

I made it with a computer.

Answer: If this will happen in the future. Then you need to use the computer to detect the data stream of this screenshot, just look at the data of the throttle when you apply the brake to see if there is any abnormal phenomenon. If there is a problem with the most basic data, it is that there is a failure and we need to replace it.

The question was washed yesterday, and today the red light was turned on and the engine went out again, and the answer asked him to check the throttle again, and use the computer to check the data of the throttle to see if there is a problem, if there is a problem with the data of the throttle, it is caused by a problem in the throttle itself, and the throttle needs to be replaced.

Let him check the throttle again, use the computer to check the data of the throttle, and see if there is a problem, if there is a problem with the data of the throttle, it is caused by a problem in the throttle itself, and the throttle needs to be replaced.

Question: Isn't that a throttle?

Answer: If there is no problem with the throttle, then this situation is that the gearbox needs to be checked, and it is possible that there is a problem with the hydraulic transmission in the gearbox, and it cannot be disconnected when the brake is pressed, and the output power of this engine is this. It can also cause stalling.

Summary. Dear, hello, I am happy to serve you, stepping on the brake will not automatically turn off the reason is as follows: Lei Ling stepped on the brake and did not automatically turn off 1

Vehicles equipped with automatic start-stop function are turned on the start-stop system by default, and suddenly it cannot be used, it may be that the automatic start-stop button on the car is pressed by mistake, resulting in the system being turned off, check whether the system is turned off. 2.The engine does not reach the normal working temperature, the automatic air conditioner does not reach the preset temperature, the battery storage power is not enough, and the direction of rotation after stopping.

Dear, hello, I am happy to serve you, the brakes will not automatically turn off the reason is as follows: Lei Ling does not automatically turn off the brakes 1Vehicles equipped with automatic start-stop function are turned on the start-stop system by default, and suddenly it cannot be used, it is possible that the automatic start-stop button on the car is mistakenly pressed, resulting in the system being closed, check whether the system is closed.

2.The engine does not reach the normal working temperature, the automatic air conditioner does not reach the preset temperature, the battery storage power is not enough, and the direction of rotation after stopping.

I don't know what's going on.

Dear, stepping on the brakes will not automatically turn off the ignition for the following reasons: stepping on the brakes does not automatically turn off 1Vehicles equipped with automatic start-stop function are turned on the start-stop system by default, and suddenly it cannot be used, and the lead spine may be that the automatic start-stop button on the car is pressed by mistake, resulting in the system being closed, check whether the system is closed.

2.The engine does not reach the normal working temperature, the automatic air conditioner does not reach the preset temperature, the battery storage is not enough, and the direction of rotation after stopping.

Extended information: As the name suggests, the chain calling pedal is a pedal that restricts power, that is, the pedal of the foot brake (service brake), and the brake pedal is used to slow down and stop. It is one of the five major sail control parts for car driving.

The frequency of use is very high. How the driver's control directly affects the driving safety of the car.

The function is to reduce the meaningless idle consumption of the engine when waiting for a long time at a red light or similar temporary parking conditions, and incidentally also reduce noise and vibration, the core purpose is to make this car run a good result in fuel consumption and emissions tests.

This is because the braking system is faulty, and once the linkage between the engine and the brakes fails during the driving process, it will cause the brakes to stall.

This situation is not normal. It is recommended that you go to a professional repair shop for a certain inspection. Because most of the automatic transmission cars nowadays, applying the brakes can only stop the car. It is impossible to be in a state of flameout.