The computer automatically shuts down, and then it can t be opened, and it will drip drip

This is the alarm of the host hard disk, indicating that you can't find the hardware in the chassis for some reason, most of it is the hard disk, memory module, graphics card, loose or falling off, you can disassemble the chassis yourself and plug the above hardware from the new.

Power supply problems, 1 check the motherboard power supply filter, electrolytic bulge, leakage, discoloration 2 change a power supply and try [elimination].

Summary of the reasons for the automatic restart of the computer software - -

1 Viruses. When the "Shockwave" virus occurs, it will also indicate that the system will automatically activate after 60 seconds.

The Trojan takes control of everything on your computer from a remote control, including getting your computer back up. It is recommended to use high-quality antivirus software such as Kingsoft Antivirus (free) and Kaba (paid) to disinfect your computer.

2 System file corruption.

The system files are corrupted, such as the fonts under Win2K, the fonts under the Win98 Fonts directory and other basic files during the system runtime are corrupted, and the system will be forced to restart because it cannot complete the initialization when it starts.

Workaround: Overwrite install or reinstall.

3 Timing software or scheduled task software works.

If you set up in the Schedule Taskbar to restart or load certain workers, the computer will start up again when the scheduled time comes. In this case, we can open the "startup" item, check whether there are any executable files or other scheduled workers that we are not familiar with, block them and then boot them to check. Of course, we can also directly enter the "msconfig" command in "Run" to select the startup item.

The possibility of a motherboard is relatively high!!

But on the individual motherboards, there are temperature probes (temperature measurements).

If the temperature is not enough, it will not start!! So these questions you have to be sure about as well!!

This should be a problem with your computer program.。。 It's not a computer hardware problem, it's best to get a computer repair point to redo a new system, of course, it's best to back up the files in your computer before making a system.

Hardware short-circuited or the power supply is insufficient.

The computer switch is broken or stuck.

Are the three lights on the keyboard? Not lighting up is a motherboard issue.

It should be a virus in the capital.,Two days ago, a colleague's machine kept restarting.,Just restart it as soon as you enter the desktop.。

Check the various hardware interfaces, especially the memory modules.

Generally, the memory is in poor contact, and it should be fine to erase it with an eraser after unplugging.

Hello friends!

When you first start up your computer, press F8 and select "Last correct configuration that worked" or Safe Mode, and it may be fixed.

When you're done, please give me the answer. Thank you.

Is there a set of safety protection measures, it will shut down when it reaches a certain temperature, Master Lu has this function, and the temperature will be shut down if the temperature is too high!!

If the memory module or other PIC card is not plugged in, there may be a ticking sound.

Remove the memory module, erase the gold finger with an eraser, and then try to put it back on.

Hardware alarm, is the memory there is a problem, under normal circumstances, a long and two short alarm drops of the sound are the memory for a long time by oxidation, resulting in poor contact, not if you don't move it, it will not be a problem, hehe.

Let's take a look at the BIOS of that factory first:

award bios：

1 Short: The system starts normally.

2 Short: Regular error. Workaround: Reset the BIOS.

1 long and 1 short: There is an error with the RAM or motherboard.

1 long and 2 short: The display or graphics card is wrong.

1 long and 3 short: The keyboard controller is wrong.

1 Long 9 Short: Motherboard Flash RAM or EPROM error, BIOS corruption.

Constant ringing (long sound): The memory module is not plugged in tightly or is damaged.

Keeps ringing: The power supply and monitor are not properly connected to the graphics card.

Repeated, short ring: There is a problem with the power supply.

No sound and no display: There is a problem with the power supply.

awi bios：

1 Short: The memory refresh failed. To solve the problem, replace the memory module.

2 Short: The memory ECC verification error is incorrect. Solution: Go to CMOS settings and turn ECC verification off.

3. Short: The basic memory of the system (the first 64KB) failed to be checked.

4 Short: The system clock is wrong.

5 Short: CPU error.

6 Short: Keyboard controller error.

7 short: The real mode of the system is wrong and cannot be switched to protection mode.

8 Short: A memory error is displayed. Note: The memory of the graphics card is referred to as the video memory.

9 Short: ROM BIOS check and error.

1 long and 3 short: memory error.

1 long and 8 short: A test error is displayed.

phoenix bios

1 Short: The system starts up normally.

1 short, 1 short, 1 short: The system power-on self-test initialization failed.

1 Short 1 Short 2 Short: Motherboard error.

1 Short 1 Short 3 Short: CMOS or battery error.

1 short, 1 short, 4 short: ROM BIOS verification failed.

1 Short, 2 Short, 1 Short: The system clock is incorrect.

1 short, 2 short, 2 short: DMA initialization failed.

1 Short 2 Short 3 Short: DMA page register error.

1 Short, 3 Short, 1 Short: RAM refresh error.

1 Short, 3 Short, 2 Short: Basic memory error.

1 Short 3 Short 3 Short: Basic memory error.

1 short, 4 short, 2 short: The basic memory verification is incorrect.

1 Short 4 Short 3 Short: EISA sequencer error.

1 Short 4 Short 4 Short: EASA NMI port error.

2 Short 1 Short 2 Short to 2 Short 4 Short 4 Short (i.e. a combination of all sounds that start as 2 short): Basic memory error.

3 Short 1 Short 1 Short: Error from DMA register.

3 Short 1 Short 2 Short: The main DMA register is wrong.

3 Short 1 Short 3 Short: The main interrupt processing register is incorrect.

3 Short 1 Short 4 Short: Handle register errors from interrupts.

3 Short 2 Short 4 Short: Keyboard controller error.

3 Short 3 Short 4 Short: The display card memory is wrong.

3 Short 4 Short 2 Short: Error is displayed.

3 Short 4 Short 3 Short: No read-only memory is found.

4 Short, 2 Short, 1 Short: Clock error.

4 Short 2 Short 2 Short: Shutdown error.

4 Short 2 Short 3 Short: A20 Door Error.

4 Short 2 Short 4 Short: Protected mode interrupt error.

4 Short, 3 Short, 1 Short: Memory error.

4 Short 3 Short 3 Short: Clock 2 Error.

4 Short 3 Short 4 Short: Real-time clock error.

4 short, 4 short, 1 short: The serial port is wrong.

4 short, 4 short, 2 short: the parallel port is wrong.

4 Short 4 Short 3 Short: Digital coprocessor error.

A few short beeps And there's the award bios where you see what your bios are:

Constant ringing (long sound): The memory module is not plugged in tightly or is damaged. If it still doesn't work, you can only replace a memory module.

Ringing: The power supply and monitor are not properly connected to the graphics card. Check all the plugs.