How to install accessories for such a bathtub and what are the accessories for installing a bathtub

Do you only sell accessories? That's not a lot of money. Personally, I don't think it's very profitable, or the toilet bathroom cabinet is written to make money.

The most basic ordinary bathtub is: bathtub cylinder, water drainer + elbow + drain pipe (composed of the so-called water drainer), hot and cold water faucet, water waterfall, shower (whether you know the noise depends on the personal use of the situation), faucet hot and cold water inlet stainless steel mesh pipe, the rest depends on their own needs to increase, and the installation master can be installed by communicating with the installation master in advance.

Bathtub installation: 1. Test whether the water is leaking.

Before installing the bathtub, you should first install the drain accessories where the bathtub is placed, then fill the bathtub with water, close the drain, and check whether the bathtub is leaking. When the water exceeds the upper overflow and the water slowly flows out of the overflow, you can reach under the tub and feel the back of the overflow to see if there is any leakage. After testing the overflow, the next step is to check the airtightness of the sewer, and you can choose the method of standing to observe the airtightness of the sewer.

Second, the leveling of the bathtub.

When placing the bathtub, it is important to note that one section of the drain is lower than the other end, so as to ensure the smooth discharge of sewage in the future. However, some bathtubs have a slope for drainage at the bottom of the tub, so you don't have to think about the location of the tub when placing it.

3. Sand filling. Some cast iron bathtubs may seem to be quite strong, but their thermal conductivity is very fast, and the bottom of the bathtub should be firmly and smashed with medium river sand during installation. In the process of filling river sand, the sewer should be sealed with glass glue first, and then the entire sewer and sewer pipe should be entangled with plastic sheeting to prevent sand from leaking into the sewer pipe.

Fourth, leave the maintenance port to sell quietly.

There is a hole of 300 high and 400 wide at the sewer, and a hole is cut off according to the size, and then the wooden board (thickness 40) of the same size, which has been waterproof and anticorrosive, is intercepted, and the bricks are attached to the wooden board according to the calculated number and arrangement of bricks on the board. Extend the edge of the brick and apply sealant to the box.

Fifth, tiling. The tiling of the bathtub skirt does not need to be scratched, and the brick platform should be smeared with a layer of cement mortar on the surface, and then wait for two days before the tiles can be laid. Tiling is a very troublesome thing, because the ground leaves a slope, and the bathtub is flat.

Therefore, each large brick needs to be polished to a different size, but not a lot at one time, so as not to grind again in the future. In addition, the upper edge of the brick should be tucked under the rounded edge of the bathtub so that no sunny angle is formed.

If you install a bathtub in the bathroom, it is convenient to take a bath at ordinary times, which brings great convenience. So how to install the bathtub? PChouse will take you to find out.

1. Use bricks to build a frame foundation (skirt bathtub can omit the outer foundation).

2. A manhole of not less than 40 cm and 50 cm must be opened.

3. The bottom of the bathtub must be filled with yellow sand, which can be used as a protective layer and moisturizing.

4. The bathtub falling water and the drainage system must be connected with a hard pipe and sealed with sealant to prevent water leakage, water seepage and backwater.

5. It is strictly forbidden to increase the height of the skirt bathtub, and the upper edge of other types of bathtubs should not be higher than 50 cm.

6. The junction between the bathtub and the wall must be sealed with anti-mildew sealing paste.

7. If the steps are installed, anti-slip materials must be used, and the width of the steps should not be less than 30 cm, and the steps should not be more than two steps.

8. After the installation is completed, fill the tank with water, flush it once every 4 hours, a total of 2 times, and check whether the water seepage at the water drop place after the bathtub is flushed.

The bathtub has always been the best choice for everyone to enjoy bath time, but everyone knows ifBathtub installationIf it is improper, there will be potential safety hazards, so how to install a household bathtub? Below we will bring you the bathtub installation method and precautions, I hope it can be helpful to you.

Preparation for bathtub installation:

Before we install the bathtub, the preparation must be done sufficiently, the first thing we need to understand is the specific pure height of the bathtub, after measuring the height, we should draw a horizontal line of the height of the bathtub at the approximate position of the wall against which the bathtub is leaning, and if the bottom of the bathtub is to be raised, don't forget to calculate the height of the pad.

Then there is the installation of the floor drain, after we decorate the house, the bathroom will definitely leave a drainage hole, we only need to connect the floor drain of the bathtub with the original design of the floor drain when installing the bathtub, if there is a gap during installation, you can use putty to fill the gap.

How to install a household bathtub?

1. Installation method of freestanding bathtub:

The installation of free-standing rock scale bathtubs is relatively simple. Among them, the installation of water inlets and outlets is a key issue. Before installation, it is necessary to reserve or modify the bath number tank outlet and other passages, and then place the bathtub on two wooden strips, connect the upper and lower water, try to fill the bathtub with water, and check whether the drain is leaking.

If there is no leakage, the strip can be removed. The bathtub is basically installed.

2. Installation method of built-in bathtub:

The focus of built-in bathtub installation is to do a good job of waterproofing. The main steps are, after the pipe of the bathtub is done, in order to achieve the effect of waterproofing, the slotted part should be repaired, and it is best to detect whether there will be water leakage within one or two days; The ground is laid under the normal order; Use foam bricks to cushion the built-in bathtub, and the height is generally within 60cm; Note that there is a 250x300mm normal size manhole at the location of the sewer pipe.

Precautions for bathtub installation:

1. Check whether the level, front and back, left and right positions of the bathtub are appropriate, check whether the drainage facilities are suitable, install them firmly, and take anti-dirty, anti-bump and anti-clogging facilities for the bathtub and sewer facilities during the installation process, and do not splash the sparks of the angle grinder and spot welding machine on the bathtub, otherwise it will cause damage to the glaze surface and affect the beauty of the bathtub.

2. The installation of the jacuzzi must be equipped with a grounding wire and a leakage protection switch, and after the installation is connected, the electric plug should be connected and waterproof around the backing plate to avoid leakage accidents. Before connecting the water pipe, the motor should be energized to test whether the sound meets the requirements.

3. Before installing the bathtub with bracket, check whether the bathtub is placed on the ground flat; Once the tub is placed in the reserved position, the support leg nuts should be adjusted with the help of a level until the tub is level.

4. Pay attention to bathtub protection, in the process of bathtub installation and house decoration, you can cover the surface of the bathtub with soft materials, do not stand on the bathtub for construction, or place heavy objects on the edge of the bathtub to prevent damage to the bathtub. The bathtub can only be used after 24 hours of installation.

The above is how to install a household bathtub for you? The whole content of the precautions for bathtub installation.

The installation method of the bathtub is as follows:

1. The first thing is to choose the appropriate size bathtub according to the specifications of the bathroom. I believe everyone will notice that choose the right bathtub size according to the size of your own bathroom, so in the early stage of installation, you must first compare the size of the bathtub and the reserved location and space of the bathroom.

2. When installing the place, according to the actual size of the bathtub, the skirt should be built with brick and cement, the exterior and the upper part of the skirt should be tiled, and the bottom should be built with bricks and cement, and the height should be just at the bottom of the bathtub.

3. How to install the bathtub, there are also requirements for the use of glass glue, although the volume of the bathtub is relatively heavy, but in order to stabilize the bathtub and prolong the service life of the bathtub, it is recommended to put glass glue on the place where the bathtub and the skirt and the wall are in contact. This ensures that the bottom of the bathtub is dry and prevents water from entering, which can extend the service life.

4. The upper plane of the bathtub installation must be checked and smoothed with a level, and it cannot be tilted sideways. The junction between the side of the upper mouth of the bathtub and the wall is best filled with sealing paste. The connection between the bathtub drain and the drain pipe must be firm and easy to disassemble, and the connection should not be open.

5. When building the bathtub skirt, for aesthetic considerations, all the height of 600 is reserved, other materials such as mosaics are abandoned, and the bathtub skirt uses the same bricks as the lower part of the wall tiles.

6. Finally, in order to give you a little suggestion on the installation method of the bathtub, in order to stabilize the bathtub and prolong the service life of the bathtub, it is recommended to put glass glue on the place where the bathtub is in contact with the skirt and the wall, which can effectively keep the bottom of the bathtub dry, so as to prolong the service life.