-
1. Before choosing a toilet on the market, first determine the size of the water in the seat (i.e., the distance from wall to wall). Before installation, please make sure that the product accessories you choose, completed, please carefully review this manual and learn about some products.
2. Determine the height of the drain according to the condition of the toilet and cut off the rest of the part. The goal is to make the plumbing and toilet bottom more consistent. Start by using a hacksaw or cornea for the sewer according to the horizontal height of the centimeter, because the flange of the toilet bowl is soft.
If it is not centimeters high, there may be water seepage problems, and centimeters are more tightly fitted.
3. Measure the pit distance. Before choosing a toilet, first determine the size of the water inside the house, that is, the distance from the wall to the water. When using a toilet, if you want to decorate the tiles, you must measure the pit distance after applying the tiles. Otherwise, the toilet will be bought back and cannot be installed.
4. Install the flange ring provided with the toilet at the drain. Remember to press hard to ensure the compaction of the flange ring and toilet drain. Place the flange on the toilet drain.
Then carefully align the lower hose and lower it smoothly. At this point, the wall of the sewer pipe is inserted into the viscous clay of the flange for sealing.
5. After the water test is completed, start to install the cover.
6. Glue around the toilet, this step is also very important, not only to stabilize the toilet, but also to prevent the smell of the net from being released from the toilet. Therefore, we will not only fight, but also four whole weeks. At the intersection of the toilet bowl and the outer surface of the floor, since the toilet bowl and the floor are not one, a joint seal transparent sealant can be used for agitation, and the outer opening of the toilet bowl is sealed to maintain the integrity of the floor.
Some bathroom water can clog around the toilet bowl. Note: If you need to install the set screws, first apply a special sealant installed in the toilet bowl evenly over the outside 2cm of the toilet base.
The drain of the toilet bowl should be pulled towards the center of the drain. Expansion bolts are located on the left and right sides of the toilet, remove the toilet, punch holes and raised bolts.
7. Install or debug the water tank accessories.
8. After installing the toilet, wait until the glass glue (putty) or cement mortar has solidified before releasing water. The curing time is usually 24 hours.
-
How to install a toilet at home.
-
This kind of toilet mat is the same suitable for the O-shaped U-shaped toilet, this kind of toilet mat is more troublesome, first of all, the toilet mat will be placed under the toilet lid, the seat plate is upright, and then the inner ring of the elastic band is turned out from the hole in the reverse seat, remember that the circle without a hard ring passes through the toilet seat as a whole, wraps a part of the cover, and finally turns down the outer ring of the plastic pipe to cover the bottom of the seat.
-
The steps to install the toilet are as follows:
1. Check the leveling between the sewage pipe and the ground.
It is necessary to check whether there is any blockage of sediment, waste paper and other debris in the sewage pipe, and at the same time, it is also necessary to check whether the ground is level before and after the toilet is installed, and the unevenness needs to be leveled.
2. Determine the center of the sewage pipe.
The method of confirming the center of the sewage pipe is very simple, that is, turn the toilet over, and then draw a cross center line at the center of the toilet outlet, and pay attention to the lower cross center line to extend to the bottom of the toilet and the feet around it.
3. Fix the toilet.
First align the toilet with the cross line of the ground sewage outlet, ensure that the toilet is installed horizontally and then press the seal tightly, and the next step is to install the screws and decorative caps of the feet to fix the toilet.
4. The bottom is sealed.
After fixing the toilet, it is necessary to install a special sealing ring at the sewage outlet, or apply a circle of glass glue (putty) or cement mortar around it, and the ratio of cement to sand is recommended to be 1:3.
5. Install the water tank accessories.
Rinse the pipes with water for 3-5 minutes. After ensuring the cleanliness of the tap water, the angle valve and the connecting hose are installed, and then the hose is connected to the installed water tank fittings.
6. Debugging and inspection.
The last step is to inspect the toilet, check whether the location of the drain valve is flexible, whether the inlet valve and seal are normal, whether there is jamming and leakage, pay attention to see if the inlet valve is equipped with a filtration device, etc., if not, it is recommended to install.
This solves the problem of installing a toilet.
-
Here's how to install the toilet:
1. Check the leveling between the sewage pipe and the ground.
First of all, when we install the toilet, we need to have an overall view of the sewage pipeline, check whether there is any blockage of debris such as sediment in the pipe, and at the same time, check whether the ground around the location of the toilet is horizontal, if the floor is uneven, you need to level the ground before installing the toilet.
2. Determine the center of the sewage pipe.
I believe everyone knows that the toilet has a sewage center, and before installing the toilet, it is necessary to determine its sewage pipe center. We can turn the toilet upside down, and then determine the Zhongzheng friendship on the toilet drain, at this time, draw a cross center line in its center, and the center line of the cross should extend to the bottom of the toilet and the feet around it.
3. Fix the toilet.
Through the above two steps, the next step is to fix it, when fixing the toilet, it is necessary to align the cross line between the toilet bowl and the ground sewage outlet, and when ensuring the horizontal installation of the toilet, press the sealing ring tightly, and finally install the screws and decorative caps of the anchors.
4. Do a good job of bottom sealing.
It is necessary to install some corresponding sealing rings on the sewage outlet, such as coating a circle of glass glue (putty) or cement mortar around the perimeter, and the ratio of cement to sand is 1:3.
5. Install the water tank accessories.
Finally, we can install the fittings for the water tank, and we can first put in the water for 3 to 5 minutes to flush the pipes. After making sure that the water pipe is clean, you can install the angle valve with the connecting hose, and then connect the hose to the installed tank fitting to connect the water valve to ensure that the water source can be pressed.
6. Adjust the width of the Zheng test inspection.
In order to ensure the success of the installation, it is necessary to re-inspect the toilet, not only to see whether the inlet valve and seal can be normal, whether the installation position of the drain valve can be flexible, whether there is any jamming and leakage, and whether the inlet valve is equipped with a filtration device.
-
Here's how to install the toilet correctly:Tools Raw material: toilet.
1. Before installing the toilet, clean up the sewage pipe on the ground, and clean up the cement blocks or porcelain powder and other sundries that were accidentally put in during the decoration to avoid blockage. After cleaning, you can install the toilet.
2. When installing the toilet, the most important thing is the sewage pipe of the toilet, which should be facing the sewage pipe or shifter on the ground, so as to ensure that the dirt will not flow out.
3. The sewage outlet of the toilet should also be equipped with an anti-leakage device.
4. After the toilet is installed, adjust the position of the water tank, you can use some useless things, but it must be a substance that is easy to decompose, put it in the toilet, and conduct multiple flushing tests.
5. After the water tank is adjusted, the toilet is installed.
-
Here's how to install the toilet:
Tools: toilet, glass glue, wrench, ruler, marker, level, steel ruler.
1. Before installing the toilet, a comprehensive inspection of the sewage pipeline should be carried out to see if there is mud and sand, waste training and other debris blockage in the pipeline, and at the same time check whether the ground of the toilet installation position is horizontal.
2. Determine the center of the sewage pipe. Flip the toilet, determine the center on the toilet drain, and draw a cross center line, which should extend to the bottom of the toilet bowl and the feet around the loss.
3. Align the cross line between the toilet bowl and the ground sewage outlet, keep the toilet installed horizontally, press the sealing ring tightly, and install the anchor screws and decorative caps.
4. Install a special sealing ring on the toilet drain, or put a circle of glass glue or cement mortar around it, and the ratio of cement to sand is 1 to 3.
5. Then the toilet is ready.
-
Toilet, every family is an indispensable bathroom product reputation, the installation of the toilet is actually relatively simple, but masteryHow to install a toiletThe method is very important so as not to install it incorrectly and affect future use! Let's follow us to learn together!
1. Take out the pipe plug of the ground drain outlet, check that there is no debris in the pipe, and clean the area around the pipe mouth.
2. The ground of the toilet must be hard and flat. Floor tiles or other decorative materials should not be paved, and sand and gravel debris should be cleaned up.
3. Before the toilet is fixed. To make it level and calibrate it with a level.
4. There are two options for fixed toilets:
a. Pull burst bolt fixing method: put the toilet in the installation position, draw the contour line of the toilet foot on the ground, and draw the bolt hole position through the installation hole on the toilet. After the hole is drilled in the trace section, insert the detonation bolt, apply adhesive at the joint between the toilet discharge outlet and the ground sewage outlet, put the toilet smoothly, firmly pull the burst bolt, and finally seal the toilet foot with cement mortar.
B. Cement bonding method: draw the toilet bottom caster corridor line on the ground, lay a circle of 30mm wide and 15mm high cement mortar inward along the contour line, apply adhesive at the junction of the toilet outlet and the ground sewage outlet, wipe the toilet foot, and place it smoothly in the installation position to make it firmly bonded and wipe off the overflowing cement mortar.
5. The cement slurry adhered during construction must be removed before the cement is dry, so as not to be difficult to remove after drying.
6. Connect the water inlet pipe and make sure that there is no leakage.
7. After about one hour, the water is continuously tested several times to ensure that the sewage pipe is unblocked. Test the sewage effect of the toilet bowl by filling the accessories in the water tank, filling it with water, placing a piece of toilet paper in the toilet and dripping a drop of ink, leaving no traces at one discharge, indicating that the water is unobstructed.
8. The toilet should not be used within three days after installation, so as not to affect its stability.
Do you do engineering or home improvement? It can be seen in the general hydropower diagram.
First of all, of course, you have to bring the office installation package back**,**The method can be seen in this article:ppt2010 software**,ppt software is also included in it。 So how do you install it? >>>More
One. Partition. A partition is a part of a hard disk that is built as a separate storage area, which is divided into a primary partition and an extended partition. >>>More
You install the old CPU again and try it, if it can start normally, it may be caused by your CPU and the motherboard is not compatible, or it may be caused by the fact that you did not install it when you installed it, if it can't start normally, it means that you have touched other hardware, such as memory modules, loose display ports, etc., check it well, be careful, you can find me if you have any problems.
How to set up a wireless router.