How to fix the blue screen when disk defragmentation?

This is what it means: it means that the kernel data that needs to be used is not found in virtual memory or physical memory. This error is often a sign that there is a problem with the hard drive, that the data is corrupted or that the virus is attacking.

It may be that the bad sectors are caused by the phenomenon of giving you a few bad sectors.

1) When reading a file or running a program, the hard disk repeatedly reads the disk and makes an error, prompting information such as file corruption, or it takes a long time to succeed; Sometimes there is even a blue screen, etc.;

2) The sound of the hard disk suddenly changed from the normal friction sound to a strange sound;

3) The system cannot start normally when virus infection is ruled out, and prompts such as "sector not found" or "general error in reading drive c" appear;

4) information on the hard disk, to a certain progress stopped, the last error is reported, can not be completed;

5) Every time the system is turned on, it will automatically run scandisk to scan for disk errors;

6) When executing fdisk on the hard disk, it will repeatedly advance and retreat to a certain progress;

7) The system cannot be booted through the hard disk during boot, and it can be turned to the hard disk letter after booting with a floppy disk, but it cannot be entered, and the system can not be successfully transmitted with sys commands. In this case, it is very likely that there is a problem with the boot sector of the hard drive. See if you have one?

If there is, you can use this software to fix the HDD Regenerator shell, which is the common HDD, you can see if you can solve it, if not, then leave me a message! Tell me when you reply about your hard drive usage (time) If there are bad sectors, try not to format it.

Have you repaired your hard drive?

First of all, we must know what disk fragmentation is, as the name suggests, it is the first beam of a bench, a part of the east and a part of the west, which will not cause a "blue screen restart", and more fragments will have some impact on performance, the addressing time will be very short for solid state drives, and if it is a mechanical hard disk, the addressing time will be relatively long, because there is mechanical movement, so if it is a mechanical hard disk, it is best to regularly do disk defragmentation for the file system, which can improve performance.

There are many problems that cause "blue screen restart" restart, if you look at the disk problem alone, it is best to scan the hard disk for bad sectors, because if there are bad sectors, it will also cause a blue screen, DiskGenius can detect the bad sectors of the hard disk, and you can list the response time, and you can also repair the bad sectors of the hard disk, it is recommended to enter Windows

PE environment, or DOS environment to run DiskGenius to detect, because if the system is running during the operation of the test results will affect the detection results, it will be inaccurate.

Too much disk fragmentation will not cause the computer to reboot with a blue screen, but will only cause the system to run slowly.

No, even if your computer is a vintage computer. (Insufficient memory, CPU single-core case).

It's just going to crash.

The reasons for the computer blue screen are complex! (The answer is original, copying is strictly prohibited).

software, full scan).

2。The computer system has stubborn viruses and Trojan horses or worms interfere with, or the system files have been lost (360 system emergency.

Rescue box or Kingsoft first aid kit, Kingsoft net shield, etc., any of them, all the killing, and then repair).

4。There are new vulnerabilities waiting to be installed in the system (patched for high-risk and important, others are set to: ignore).

5。Unnecessary similar software installation, (360 Butler, software uninstall, find uninstall, again: strong cleaning) stupid dust.

6。The graphics card or memory CPU is in poor contact and loose or has dust covered, (unplug the eraser).

7。The memory CPU is overheated, and the heat dissipation is not good! (Don't turn on for too long, turn off and dissipate).

8。If you still can't get in the bend chain, it means that the system files are missing! Or maybe there's a serious error in the system memory!

9。Try to press F8 after booting, press Enter, Enter, enter into safe mode, configure correctly for the last time, and press down.

Try it! Or, go into safe mode, go to the desktop, and get a full antivirus!

10。Playing games on the blue screen, generally the system does not support this game! (Change the game version or change the XP system).

Reinstall or upgrade to the latest version).

12。If it still doesn't work, you need to "one-click restore" the system or "reinstall the system"!

First of all, we must know what disk fragmentation is, as the name suggests, it is a file, a part of the east storage, a part of the west storage, will not cause a "blue screen restart", more fragments will have some impact on performance, for the solid state drive the addressing time will be very short, if it is a mechanical hard disk, the addressing time will be relatively long, because there is mechanical movement, so if it is a mechanical hard disk, it is best to regularly do disk defragmentation for the file system, which can improve performance.

There are many problems that cause "blue screen restart" restart, if the disk problem alone, it is best to scan the hard disk for bad sectors, because if there are bad sectors, it will also cause a blue screen, DiskGenius can detect the bad sectors of the hard disk, and the response time can be listed, and the bad sectors of the hard disk can also be repaired, it is recommended to enter the Windows PE environment, or run DiskGenius in the DOS environment to detect, because if the system is running during the operation process, the detection results will be affected, would be inaccurate.

I don't think so. Just affect the hard drive seek.

If a file structure in the file system of the F drive is damaged, it is recommended to copy the important files in the F drive to another place, and then format the F drive.