After the tap water is broken for a while, it is repaired, some faucets have water, and some have no

This situation may be caused by a blockage of some water pipes, or it may be accidentally connected to the wrong water during maintenance.

When renovating a house, some faucets are equipped with a tap valve, while others are not, so there may be no water after the water is turned on because the valve is closed.

A faucet with water is unobstructed, and a faucet without water is either a broken pipe or a faulty faucet.

A: 1Water pipes are blocked by foreign objects; 2.The water pressure is not enough; 3.There is a problem with the faucet.

If it is a faucet or angle valve with a filter for home decoration, it may be because the impurities in the water are blocked due to maintenance, and you can disassemble and clean it. If it is an old-fashioned knob faucet, it is estimated that it will be glued to it without a rubber pad for a long time, and it will be good to take it apart and make it out.

If the hands-on ability is not strong, it is recommended to ask the hydropower master to get it.

If it is repaired, there will be water, unless some faucets are blocked or there is a lot of air, and it will take a while to put the water out.

There are two possible possibilities.

One is that the water flow is not enough and not all of it is open.

Not every one is guaranteed.

It may also be that there is a blockage and the throughput is reduced.

The faucet is clogged.

Some of the faucets are blocked. Remove the faucet.

The pipes of the water are broken. Some have water, some have no water.

Summary. Kiss. Hello, I am happy to answer for you, the answer to your question is: if the inlet valve of the faucet is half-open or completely closed, it will cause the faucet to fail to produce water, then you only need to fully open the valve of the faucet.

Kiss. Hello, I am happy to answer for you, the answer to your question is: if the water inlet valve of the faucet is in a half-open or completely closed state, it will cause the faucet to fail to produce water, then you only need to sell orange cover to fully open the valve of the faucet.

After the faucet has been used for a long time, the internal filter has accumulated a lot of limescale or stains. This requires removing the faucet, removing the filter, and cleaning the code. After the cleaning is completed, install it back to the wild acacia elimination.

If the water pipe connected to the faucet is broken, it will also affect the water output of the Bihong faucet. At this time, you need to find the leaking water pipe, cut it off, and replace it with a new water pipe.

What should I do if the faucet is replaced several times, but it still leaks?

1. The reason for the leakage of the water outlet: it is caused by the wear of the shaft gasket in the faucet. Use pliers to loosen the gland and remove it, take out the shaft gasket with a clip, and replace it with a new shaft spacer.

2. The reason for the leakage of the gap in the lower part of the faucet: it is caused by the wear of the triangular gasket in the gland. You can turn the screw loose finger to remove the tie, then loosen the gland and remove it, and then take out the triangular seal on the inside of the gland and replace it with a new one.

3. Leakage at the joint of the pipe: Roughly speaking, the cap type is only when the nut is loosened, then you can re-tie the cap nut or replace it with a new Qingcha U-shaped gasket.

If the faucet is broken, you need to close the water valve first to prevent the faucet from seeping. Then find the cause of the damage to the faucet, the faucet is not tightened, the valve core is leaking, the bolt is leaking, etc., you can reinstall it by winding the raw material belt at the interface. When the mouth of the shed is broken, a new faucet needs to be replaced.

1. Close the water valve

After the faucet is broken, the first thing to do is to close the water valve to prevent the faucet from seeping out.

2. Find the reason

There are many cases of faucet damage, such as broken joints, untightened tightening, water seepage at bolts, water seepage at faucet valve core, etc.

3. Treatment method

If the faucet is not tightened, water seeps at the valve core, water seeps at the bolt, etc., the faucet can be unscrewed, and the raw material belt can be wound around the interface several times before reinstalling. When the interface is broken and cracked, it needs to be replaced with a new faucet.

The faucet is still dripping if it is due to a broken gasket. Maintenance and replacement steps: 1. First of all, close the water valve, which is at the front of the water meter to control the water source in the whole house.

The faucet wrench has a gelatinous logo on it (old-fashioned copper faucets don't have this), and the screws inside can be seen by prying it open with a razor. Unscrew the screws with a screwdriver and set them aside, and lift the wrench up to remove. <

The faucet is still dripping because the gasket is broken.

The repair and replacement steps are as follows:

Step 1: First, close the water valve, which is at the front of the water meter, to control the water source throughout the house. The faucet wrench has a gelatinous logo on it (old-fashioned copper faucets don't have this), and the screws inside can be seen by prying it open with a razor.

Unscrew the screws with a screwdriver and set them aside, and lift the wrench up to remove.

Step 2: Remove the handle and look at the parts of the faucet. Remove the fill nut with large carp pliers or an adjustable wrench, being careful not to leave scratches on the metal. Turn the spool or shaft in the same direction you rotated when you turned on the faucet to unscrew them.

Step 3: Remove the screws that hold the washer in place. If necessary, use penetrating lubricant to loosen the screws. Inspect the screws and spool and replace them with new ones if damaged.

Step 4: Replace the old gasket with a new one that is exactly the same. A new gasket that is almost exactly a match for the old gasket will generally stop the faucet from dripping.

Step 5: Attach the new gasket to the spool and reinstall the parts in the faucet. Rotate the spool in a clockwise direction. Once the spool is in place, reattach the fill nut. Be careful not to leave scratches on the metal with the wrench.

Step 6: Reinstall the handle and put the button or disc back in. Turn the water supply back on and check for any leaks.