How do I change the oil in my car, and are there any steps to do it?

1. Choose the right oil:First of all, before we change the engine oil, we need to choose a suitable engine oil for the car, because the engine oil is also divided into many grades, and when changing the engine oil, compared with the original engine oil, we can only choose a higher level of engine oil instead, or choose the same level of engine oil to continue to use, remember that you must not choose a lower grade of engine oil. When choosing engine oil, you should also pay attention to the viscosity of the engine oil to see if it meets the requirements of the use of the car.

Here we take AirMaster motor oil as an example.

2. Oil draining and inspection: After choosing a new engine oil, we need to release all the original engine oil, and we cannot mix the two engine oils. So we can twist the oil pan screws, or just twist the oil filter, and then release the previous waste oil.

After all is done, check to see if the rubber seal of the old oil filter has been removed.

If not, it needs to be removed, because if the old and new rubber seals are overlapped, it will cause oil leakage in the car. After the inspection, we can install the new oil, and pay attention to the new rubber seal, which can be applied with a film of oil to prevent friction and damage with the new filter.

3. Add an appropriate amount of engine oil: When adding engine oil, an appropriate amount is sufficient, and do not add too much engine oil. Because if there is too much oil, when the engine is started, it is likely to cause internal power loss, and in severe cases, it will burn oil.

situation. And if there is a serious shortage of oil.

This can lead to insufficient lubrication of the engine's internal bearings and journals, which can cause friction, increase wear and tear, and even burn the shaft.

Accident. Therefore, when adding engine oil, an appropriate amount can be used, not too much, not too little, and it is best to control it between the upper and lower engraved lines of the oil dipstick.

4. Check again after the oil change: After the oil is changed, we can start the car, keep the engine running for 3-5 minutes, and then turn off the engine to check the oil volume, the position of the oil pan screws and the oil filter, and check whether the oil is leaking. That's it for changing the oil.

Hello, the operation steps for changing the engine oil are as follows:

1. After the car is driven to the lift, turn off the engine, use the lift to jack the vehicle, pull up the handbrake and squeeze the front wheel with a wooden wedge;

2. Place the old oil container under the oil pan, find the oil drain bolt of the oil pan, and slowly unscrew the oil drain bolt, taking care not to touch the hot oil;

3. Move the oil container to the bottom of the oil filter, use the oil filter element wrench to loosen the filter element, and then unscrew it by hand. If the filter is still hot, remember to wear gloves;

4. Refer to the user's manual to select the appropriate oil filter element;

5. Use new oil to apply the interface gasket of the new filter element. If the filter is installed vertically, some fresh oil can be poured into the filter, which will reduce dry grinding the next engine start;

6. Pour the new engine oil into the oil pan, pay attention to the introduction of the user's manual. A funnel can be used to prevent oil from being poured on the outside of the engine.

Hello: First of all, park the vehicle in the middle of the lifting frame, and then open the engine compartment cover to protect it. Open the lid of the engine oil change, lift the car up, and unscrew the oil drain screw.

Remove the oil filter and replace it with a new one. Then lower the car and add the right amount of oil to it. Finally, use an oil ruler to measure the amount of oil.

1.Wait for the engine temperature to cool down and allow all the oil to flow back into the oil pan.

2.Use a wrench to loosen the oil drop screw, use the oil basin to catch the old oil in the oil droplet, until there is no oil flow, start the engine to work for 30 seconds, and let the oil flow out in the main oil channel.

3.Unscrew the oil filter with a special wrench; Apply oil to the oil seal of the new oil filter and tighten it clockwise by hand.

To change the oil for the car, you must first loosen the screws of the oil pan, fully drain the old oil, then tighten the screws tightly, then unscrew the cover of the oil, add new oil, and when it is almost time, the oil cap is screwed, these are the steps.

As a routine maintenance item of the car, an oil change is necessary. Specifically, the oil screws can be removed and replaced, or replaced with a pumping unit.

The steps to change the oil are as follows:

1. Select the appropriate oil, drain the oil and check. When choosing the right engine oil, you need to choose the oil grade in strict accordance with the car instruction manual, if there is no same level of engine oil, you can only use a higher grade of engine oil, and never use a lower grade of engine oil instead. At the same time, we should pay attention to whether the viscosity of the engine oil meets the requirements, and do not have the idea of choosing the right one, one barrel of AirMaster engine oil is enough.

After the technician twists the oil pan screws or twists the oil filter to release the waste oil, it is necessary to pay attention to: match the oil pan screws with a new screw washer and then tighten it; Before installing the new oil filter, it is necessary to carefully check whether the rubber sealing ring of the original old filter is removed with the filter, so as to avoid oil leakage when the new part is installed. 2. Add an appropriate amount of engine oil.

When adding engine oil to your car, you need to add engine oil appropriately according to the displacement of the vehicle, and you must not be greedy to add too much, or add too little in order to save money. If there is too much oil, it will cause internal power loss when the engine is started, and it will cause problems with burning oil. On the other hand, if the engine oil is insufficient, the internal bearings and journals of the engine will rub due to insufficient lubrication, which will aggravate the degree of wear, and in severe cases, it will cause the accident of burning the shaft.

Therefore, when adding engine oil, it should be controlled between the upper and lower engraved lines of the oil dipstick.

<> "Some car owners want to change the engine oil by themselves in order to save the cost of changing the oil, but they don't know the correct process for changing the oil. So what is the process of changing oil in a car?

First of all, you should go to a regular place to buy the suitable engine oil to ensure that the engine oil has not expired, and then you can prepare to place the old engine oil. When placing old engine oil, in addition to preparing a container for old oil, you should also pay attention to the location of the oil, which should be under the bottom shell in the lower part of the engine compartment of the vehicle.

After unscrewing the oil drain bolt, release the old engine oil, and when the old oil basically does not flow out of the skin, re-install the oil drain bolt, and do not press it too tightly during installation.

Use a tool to unscrew the oil filter element, and then take it out, maybe the position of the oil filter element of different gear buried cars is different, you can understand it before taking it out.

After tightening all the screws, pour the new oil into the engine oil tank, and the amount added should be between the highest and lowest scales, not lower than the lowest scale mark, and not higher than the highest scale mark.

In addition to changing the oil properly, it is also important to change the oil filter every time you change the oil.

It is still recommended to go to a chain store or a fast repair shop for car oil replacement.