How about changing the oil in the car? How do you change the oil in your car?

How to change the oil of your car:

1. Disassemble the bottom guard plate of the vehicle, expose the oil filter and oil drain screws, unscrew the oil drain screws on the oil pan, pay attention to the oil will spray out instantly, and the temperature is high, move the fuel tank to the bottom of the vehicle to hold the old engine oil;

2. Remove the old oil filter with a tool and turn it counterclockwise, apply a layer of oil to the rubber ring part of the edge of the new oil filter, then install it back in place, and then tighten the oil drain screw, don't push too hard, so as not to overflow the thread;

Hello, to change the oil of the car, first open the car head cover, open the oil cover, and then lift the car up, there is an oil pan at the bottom, open it, and then let the oil flow dry! It's best to fill the bottom cap and pour in new oil!

Automobile engine oil can lubricate and reduce friction, assist cooling and cooling, seal and leak prevention, rust and corrosion prevention, shock absorption and cushioning of the engine. It is known as the "blood" of automobiles.

Step 1: Turn off the car after driving onto the lift, then use the lift to jack the vehicle, pull up the handbrake and squeeze the front wheels up with a wooden wedge.

Check the drain bolts, reinstall the drain bolts, and be careful not to overtighten the bolts to prevent damage to the oil pan.

Step 3: Move the oil container under the oil filter, use the oil filter wrench to loosen the filter, and then unscrew it by hand. If the filter is still hot, remember to wear gloves.

Even if the filter element was tightened before, there is no need to worry about damaging the filter element during the removal process, as long as it does not damage the connection screws that install the filter element and the parts around the filter element, after all, we no longer use the removed filter element.

Step 4: Refer to the user manual to select the appropriate oil filter.

Step 5: Apply the interface gasket of the new filter cartridge with new oil. If the filter is installed vertically, you can pour some new oil into the filter, which will reduce dry grinding the next engine start.

Screw the filter in by hand and tighten the filter as indicated (usually after tightening the filter by hand and then screwing it in 3 or 4 turns).

Step 6: Pour the new oil into the oil pan, taking care to refer to the user's manual. A funnel can be used to prevent oil from being poured on the outside of the engine.

Check the lower part of the engine for leaks. If there is no leak, put down the vehicle, check the dipstick, and start the engine, the indicator light on the gauge should turn off immediately after starting. Finally, turn off the engine and double-check the oil level and dispose of the old oil and filters according to local regulations.

The daily maintenance of the car is mainly to replace the oil filter to effectively protect the normal operation of the engine. According to the quality of the engine oil, the synthetic engine oil can be 7000-10000 km or 5 months, and the ordinary engine oil can be changed once every 5000-7000 km or every three months.

The fuel filter is replaced once every 20,000 kilometers, and the air filter is replaced once every 10,000 kilometers. The air conditioner filter is replaced once every 1 year.

Brake fluid and booster oil are replaced once every 40,000 yuan. There is also transmission fluid, antifreeze, etc.

1. Choose the right oil for your vehicleHow to change the oil: Choose the right oil for your vehicle. First of all, we need to choose the type of lubricant, whether it is synthetic or semi-synthetic.

Before changing the oil, it is best to go around the car before draining the oil. In this way, the oil can carry out a certain cleaning function in the engine, and bring out the impurities and precipitation inside the engine. Start putting the old oil in it.

It is best to put it for ten minutes after the oil is discharged, and wait for the old oil to be drained clean, and you can also use the pumping unit to extract the waste oil. Don't be in a hurry to add new oil after putting the old machine oil, you should observe the changes in the old engine oil. If the old oil is very viscous, has significant delamination and has a bit of a foul smell, it is time to shorten the oil change interval.

If there is a gasoline pass, it means that the airtightness of the engine combustion chamber is not good, and it is better to go to the car repair shop and check it. 2. Inject new engine oil, screw on the oil change screw, start to inject new engine oil into the car, and pay attention to the amount of oil added, not exceeding the upper limit of the oil dipstick and not lower than the lower limit. After adding oil, start the car, idle for a few minutes, then turn off the engine and pull out the oil dipstick, check the amount of oil, see whether the upper limit and the lower limit of the oil dipstick are returned, if it is lower than the lower limit, then replenish the oil appropriately.

Cars are generally old and rotten according to the following methods to change the oil:

1. Change the engine oil by lifting, start the car before changing the oil, heat up the car for about 10 minutes, and the oil in the engine will be hot and pold, the fluidity is better, and it is easier to put it clean;

2. Remember to wear gloves before screwing, and at the same time put a bucket or basin under the bottom to pick up the old engine oil. There is also to open the lid of the oil filler, so that the shed can be used to use the principle of atmospheric pressure, so that the oil can flow out smoothly;

3. After these are done, unscrew the oil drain screw, at this time, the old engine oil is flowing out of the oil drain screw hole, you just wait for it to finish. After putting the oil, it is not recommended to screw the old oil drain screws back, because there are many car oil drain screw gaskets, which are metal, and they will be deformed after using once, so it is best to replace the new gasket or a new oil drain screw, which can reduce the risk of oil leakage;

4. Many repair shops don't care about these things, and they will directly install them for you. It's okay, it doesn't matter if you're a new car, so come by yourself and be careful, and the benefits are here. The new oil drain screws are installed and screwed back, and then the filter element is replaced, this Lavida oil filter element is on the oil pan, and some cars are in the engine compartment.

Millions of car purchase subsidies.

How to change the oil in the car:

1. Disassemble the bottom guard plate of the vehicle, expose the oil filter and oil drain screws, unscrew the oil drain screws on the oil pan, pay attention to the oil will spray out instantly, and the temperature is high, move the fuel tank to the bottom of the vehicle to hold the old engine oil;

2. Remove the old oil filter with a tool and turn it counterclockwise, apply a layer of oil to the rubber ring part of the edge of the new oil filter, then install it back in place, and then tighten the oil drain screw, don't push too hard, so as not to overflow the thread;

To put it simply, remove the chassis oil drain screws to drain the old engine oil first, then replace the filter, and add new oil above the engine after the screws are installed.

Try to choose multi-grade oil, multi-grade oil has a better protection effect on the engine due to saving, long life and high efficiency. Based on.

The characteristics of multi-grade oil, premature blackening may occur during use, and the oil pressure is smaller than that of ordinary oil, which is normal.

1.Fully synthetic engine oil: Fully synthetic engine oil has better high and low temperature performance, longer oil change interval and is suitable for more severe car conditions, suitable for luxury high-performance vehicles, and is replaced at about 10,000-12,000 kilometers.

2.Semi-synthetic engine oil: The replacement cycle of semi-synthetic engine oil is generally about 8000-10000 kilometers, and the performance is moderate.

3.Mineral oil: This type of oil generally needs to be replaced after about 5000 kilometers.

It depends on the type of oil to be used in the vehicle.

Generally, there are 3 types of engine oils, fully synthetic, semi-synthetic, and mineral engine oils.

Generally, fully synthetic engine oil is changed every 10,000 km or 1 year.

Generally, semi-synthetic engine oil is changed every 7500 km or 7-8 months.

The general mineral oil is changed every 5000 km or 6 months.

Hello, the current number of people consulted may not reply in a timely manner, if it is a vehicle failure problem, it is recommended to use the computer to detect the specific cause of the failure, search for "car master" can consult car problems at any time, 24 hours ** answer.

If you don't know anything about car maintenance, then you must learn a little about maintenance, so as to save time and money and keep your car healthy. Changing the oil in the car is one of the steps in maintenance. Let's learn together.

The steps to change the oil are as follows:

1. Select the appropriate oil, drain the oil and check. When choosing the right engine oil, you need to choose the oil grade in strict accordance with the car instruction manual, if there is no same level of engine oil, you can only use a higher grade of engine oil, and never use a lower grade of engine oil instead. At the same time, we should pay attention to whether the viscosity of the engine oil meets the requirements, and do not have the idea of choosing the right one, one barrel of AirMaster engine oil is enough.

After the technician twists the oil pan screws or twists the oil filter to release the waste oil, it is necessary to pay attention to: match the oil pan screws with a new screw washer and then tighten it; Before installing the new oil filter, it is necessary to carefully check whether the rubber sealing ring of the original old filter is removed with the filter, so as to avoid oil leakage when the new part is installed. 2. Add an appropriate amount of engine oil.

When adding engine oil to your car, you need to add engine oil appropriately according to the displacement of the vehicle, and you must not be greedy to add too much, or add too little in order to save money. If there is too much oil, it will cause internal power loss when the engine is started, and it will cause problems with burning oil. On the other hand, if the engine oil is insufficient, the internal bearings and journals of the engine will rub due to insufficient lubrication, which will aggravate the degree of wear, and in severe cases, it will cause the accident of burning the shaft.

Therefore, when adding engine oil, it should be controlled between the upper and lower engraved lines of the oil dipstick.

1. Disassemble the bottom guard plate of the vehicle, expose the oil filter and oil drain screws, unscrew the limb oil drain screws on the oil pan, pay attention to the oil will spray out instantly, and the temperature is high, move the fuel tank to the bottom of the vehicle, and hold the old engine oil oak;

2. Remove the old oil filter beam stove cleaner with a tool and rotate it counterclockwise, apply a layer of oil to the rubber ring part of the edge of the new oil filter, and then install it back in place, and then tighten the oil drain screw, don't push too hard, so as not to overflow the thread;

The oil itself is lubricating, and the high speed is conducive to the circulation in the engine and reduces the accumulation of carbon.

In the case of driving on the high-speed highway of Gaojiaoliang, if synthetic engine oil is used, the oil can basically be changed every 10,000 slag kilometers, and some can even be dragged up to 20,000 kilometers. If you often drive in the city, there are traffic lights when you go to **, and you will be stuck in traffic at every turn, and most of the distances of each trip are not more than ten kilometers, this kind of driving belongs to "attritional driving".

Extended Material: Common Misconceptions of Usage.

1. Add as much as you can.

The amount of lubricating oil should be controlled between the upper and lower scale marks of the dipstick. Because too much lubricating oil will enter the combustion chamber from the gap between the cylinder and the piston, and burn to form carbon deposits. These deposits can increase the compression ratio of the engine and increase the tendency to detonation; The red-hot state of carbon deposits in the cylinder is also easy to cause premature ignition, such as falling into the cylinder will aggravate the wear of the cylinder and piston, and will also accelerate the pollution of lubricating oil.

2. Additives are of great use.

A truly high-quality lubricant is a finished product with a variety of engine protection functions, a formula that already contains a variety of additives, including anti-wear agents, and the most important thing about the balance of the lubricant is to ensure that the performance is fully realized. Adding other additives by yourself not only does not bring additional protection to the vehicle, but is easy to react with the chemicals in the oil, resulting in a decrease in the overall performance of the oil.