It is said that it is very important to leave joints when laying floor tiles, why do you say so?

Because most of the people are now floor heating, if there is no gap, the later floor heating will cause tile cracking, resulting in the loss of property.

If there are no gaps, turn on the heating in winter, and due to thermal expansion and contraction, the floor tiles will be crowded together and will burst. And if it doesn't leave a gap, it's not beautiful.

Because this can make the floor tiles more stable, make the whole ground more flat, and it is easier to replace.

Leaving seams and paving can make future maintenance and maintenance more convenient. Due to the damage caused by the accidental fall of man-made heavy objects, if there is a gap, the damaged floor tiles can be easily replaced. After the tile is paved, our most intuitive feeling is that the gap is even, horizontal and vertical.

In other words, the result we end up with is a gap of the same size, which feels particularly good. After the floor tile is paved, the paving material expands or shrinks by the cold, or the floor tile also appears in such a situation, if there is not enough expansion space reserved between the floor tile and the floor tile, the floor tile can not withstand the expansion friction or the paving material loses its adhesion.

If the seam is not left for a long time, there will be a large area of drumming, and serious tiles will have a clicking sound, which can arch the floor tiles to crack. So it's important to leave a seam. Special effects can also widen the gap, such as 5mm, etc.

Like some antique bricks or exterior wall tiles, balcony strip bricks are better to leave wide joints. Bathroom wall waterproofing, this is a specification requirement, must be carried out a construction project, not waterproof, not only will cause damage to the outer wall, ground, wooden door and other items of the bathroom, at the same time, will also affect the downstairs. The porcelain tile joints can be smaller, and the ceramic bricks should be larger.

Generally, the wall tiles can be left with a seam of 1-, the floor tiles should be left with a seam of 2-3mm, even if the so-called seamless bricks, the joints should not be less than 1mm, and some special specifications of bricks.

Tile joint paving is convenient to adjust the brick spacing appropriately according to the size of the actual paving area, so that the corners of the house can use the whole brick as much as possible, which is both beautiful and time-saving and material-saving. Although ceramic tiles are now mechanized production, but in the process of product production, there will be a certain size error, if there is no seam, it is easy to appear uneven joints when tiling and plastering, affecting the beauty of ceramic tiles.

Therefore, whether it is to consider safety, or the use effect or aesthetics when tiling tiles, it is very important to leave joints for paving.

It is very important to leave joints in the process of paving floor tiles, the specific role is to prevent thermal expansion and contraction, the collision between the floor and the floor, resulting in a cracking state, and then a crack can be filled into the gap with white cement, so that it can be well filled and analyzed, so as to achieve the effect of waterproofing, so that the water will not penetrate again.

In order to make maintenance and maintenance more convenient in the future, there will be a large area of bulging after a long time without leaving joints, and the joints can avoid uneven joints when tiling and plastering, and it is also convenient to adjust the spacing of the whole brick.

In this way, you can apply some beauty cream to the gaps between the floors, which can make the structure between the floors stronger, and can also make the overall structure of the room more stylish.

These crevices avoid making the floor tiles particularly strong and allow air to penetrate a bit without damage.

As long as it is to be able to repair in time when there is a problem, and it is also very convenient to make it, it can easily pry the floor open.

If you leave a seam, you can protect the tile, you can avoid cracking, you can be particularly beautiful, why are you beautiful, you can be particularly strong, and the service life is relatively long.

Floor tiles have some changes in thermal expansion and contraction, and if you leave some gaps, you can make the floor tiles have enough space for expansion and contraction, and they are prone to cracks.

Because after leaving the seam, you have to do beautiful seams, if you don't leave the seams, there is a possibility that some floor tiles will crack, so be sure to leave the seams.

First, in order to protect the tiles

II. II. II、In order to make the tiles more beautiful

Because this can avoid thermal expansion and contraction, it can prevent the floor tiles from bulging, which is stronger and more beautiful.

If there are no seams, the floor tiles will be very susceptible to damage. And it's unsightly. If you want to remove the floor tiles in the future, you may have to tear down the whole house.

Some people are completely following the requirements of customers when laying floor tiles, and the reason why there should be gaps is also because the whole home looks better and tidier, because if there is basically no space, then it is also very troublesome in the process of replacing it in the later stage, because some people have children in their homes, and children will knock on the floor tiles if they are not sensible, so they still have to replace them after they are broken. When decorating, you have to look at your own situation, if you think this is not good, you can also choose wooden flooring, wooden flooring will be very good in the process of decoration.

Floor tile joints are very important in the process of construction, and floor tile joints can make the floor tiles more firm. Prevents deformation in future use. Generally, beauty sewing is done.

In this way, you can do a good job of sewing and prevent the floor from warping, and you can also prevent thermal expansion and contraction, which can reduce the serious impact on the ground.

This is because it is important to leave seams when laying the floor, which will make the floor look more snug and leave some gaps to avoid blistering.

It is also possible to do beautiful sewing. It will make the home very stylish, and it can also make the layout of the home very good. The color of the tiles will also look good.

Leaving the paving can make the maintenance and protection more convenient in the future. Because of the human factor, the hanging object accidentally sinks and causes the floor tiles to be destroyed, and if there are cracks, it is very easy to replace the damaged floor tiles. Although the relative density of ceramic tiles is very high, especially the relative density of floor tiles, no matter how large their relative density is, they need to suffer from the harm of thermal expansion and cold contraction.

In fact, the ceramic tile is easy to swell when heated, and it will close when the temperature decreases. If there is not enough indoor space between the floor tiles and the floor tiles, the floor tiles cannot withstand the surging friction or the paving raw materials lose their viscosity, and the floor tiles paved on the floor will be "arched" as described in the figure above.

In the link of temperature or temperature change, the mixed mortar will appear a certain telescopic type, if there is no seam, it will cause the tile to bulge or crack in the link of later application. Let's talk about geothermal heating, if you don't leave a crack for a long time, a large-scale bulge will occur, and the more serious tiles will make a gurgling sound, which can crack the floor tiles. Therefore, it is important to leave a seam.

Because it is a patchwork, there will always be some slight gaps between the tiles and tiles, and this gap will hide dirt and black, which is very inconvenient to remove. After the seam is paved, the tile grout is made, which is very beautiful and convenient, clean and tidy.

In the process of commodity manufacturing, there will be a certain size deviation (the deviation is too large is the quality of the product), if there is no seam, it is very easy to occur when the tile is paved when the gap is not leveled, endangering the beauty of the tile. It is also necessary to consider the technical problems of the engineering construction staff, because the paving of ceramic tiles must also be technical, the paving of ceramic tiles must be very proficient in technology, and the workers are in all the links of paving, it is unlikely to ensure that there is no deviation in the process of paving a brick.

Engineering buildings and other buildings need to set aside building deformation joints, so that the internal power caused by the deformation caused by temperature change can not be effective on the building, so that the service life of the engineering building is longer. If there is no gap, it will cause the effect of the adjacent tiles in the middle, and then cause the problem of hollowing, deformation, cracking, jumping and even loosening of the wall.

Because after leaving the joints, the floor tiles become particularly stable between them, and there will be no squeezing in the winter, if there are no seams, they will be squeezed together in the winter, which will lead to cracking.

Because now the home is full of floor heating, if the floor heating is not warm, it is very convenient to maintain; If the floor heating needs to be repaired in the later stage, it will damage the floor tiles.

Because this can reflect the level of a decoration master, it is very important, if the tile does not leave a seam, it is easy to cause the tile to crack in the later stage.

When laying floor tiles, it is necessary to leave joints, which can prevent the floor tiles from deforming. The seams are also left to make them more beautiful. Therefore, special attention should be paid during construction.

The principle of thermal expansion and cold contraction is ubiquitous. It is suitable for building roads and bridges and tiling tiles. The deliberately left seam is commonly called a deformation seam in everyone's life

If you don't leave that deformation seam, it will make you regret it and fall short. The immediate result of the tile without leaving a deformation joint is that the tile will stand against each other and leave the road and wall, and we generally call such a thing as the tile itself protruding. Therefore, leaving deformation seams is also a clever summary of the practical activities of ancient people.

Similarly, there are many bridge piles on the highway bridge, and there must be an important bridge pile to leave a deformation joint, which is also the principle.

Ceramic tiles generally must be embedded a millimeter up and down the course of the gap, because the tiles are shrinkage, pasted to the wall after more or less are heated expansion elements, if there is not enough to leave a certain joint tile will be connected to the surrounding tile pressure and squeeze porcelain. Wall antique tiles must be embedded 2 to 3mm gap paving, generally antique tiles are all tiles, the strength of this kind of bricks is good, the firing process is different. The flatness of the finished product will be very poor, if you do not bury a certain gap to paste the actual effect will be very bad, from the side, how many levels will not rise, and the workers will not be able to build the project stronger.

Ceramic tile error: although the tile is now all mechanical automation manufacturing, but in the process of product production and processing, there will be a certain specification error (too large error belongs to the quality of the product), if there is no seam, it is very easy to occur that the joints of the tile paving are not leveled, endangering the beauty of the tile. There is an error in the case of the construction of the project for the staff of the project:

The paving of ceramic tiles belongs to a new project with a very high grasp of the situation, the workers in the course of all the paving, it is unlikely to completely ensure that there is no error in the process of paving a brick, the mood of the workers is bad, day and night, and other different conditions of paving the tiles, the actual effect is different.

Before laying tiles, according to the total area of tiles, the total area of the wall or pavement to be tiled is marked, and the amount of tiles used is accurately measured. In the case of engineering construction, the tiles should be laid down in the order of the line and the seams, and the purpose of the seams is to better adjust whether the tiles laid down are neat and beautiful. Leave the seam again in order to tighten the tile for better next step with a stronger joint.

No seams are left behind, and it is pavedThe lower tile is difficult to adjust, the chaos is difficult to pave, and the middle of the tile is close to too much and is very easy to contradict and lead to unfirmness. The seam line is the only criterion to check whether the tile is neat or not.

Because it can make our tiles not easy to break, the purpose is to make the tiles have a space to change when the heat expands and contracts, so that the whole tile will not bulge.

Because this is to prevent the error caused by the size, it is a very professional design, if the size of the error occurs in the middle, it can be made up for because the thing will expand and contract, many people know, especially when laying tiles.

Because if the position of the seam is incorrect, it will affect the overall aesthetics, and will also affect the degree of dry and wet separation of the room; It can make the cement and ceramic tile have greater thermal expansion and contraction performance, Liu Feng can also affect the appearance of the limbs, and can make the ground look particularly smooth and tidy.

For the problem of whether the tiles laid at home leave seams, many people do not agree with each other. This is also because of the recent emergence of some of the so-called seamless splicing tiles, before the occurrence of this kind of seamless splicing tiles, everyone's opinion is actually the same, that is, the tiles must be left joints. In fact, my opinion is that all wall tiles and floor tiles must be left joints.

As a good friend asks this question today: Do you need to leave seams for wall tiles in the kitchen of the restaurant? The result I provided is that the wall tiles in the kitchen of the restaurant must be seamed.

Seams must be left not only in the process of tiling in the kitchen of the restaurant, but also in the bathroom of everyone's home and other areas of the room in the home. For the total width of the tile joint, it should be carried out according to the needs of the tile itself. Ceramic tile products stipulate the minimum value of the tile gap, not that the maximum value of the tile gap is larger, and the maximum value is not standardized.

As we all know, almost any object has a heat rise and cold contraction. In other words, he expands slightly when he is exposed to heat, and closes slightly when he is cold. If there is not enough amount of space between the two tiles, then in the case of tile expansion and telescopic type, the two tiles will bear the force and squeeze together, and then there will be a situation where the tiles commonly used in everyone's home are arched, or even cracked, and other wall hollows.

And the expansion and closing amount of all the tiles are related to the characteristics of the tiles themselves. The characteristics of the tiles mentioned here, in fact, one of the points in a nutshell is the relative density of the tiles. If the hardness of a tile is, the less it expands and closes.

And the lower the hardness of the tile, the greater its expansion and retraction. This can also show from another area that the higher the quality of a tile, the lower its need for this gap. And the worse the quality of this tile, the greater the need for this gap.

Therefore, no matter what kind of tile it is, no matter where it is paved, my proposal to you is that you need to leave seams according to the standards of this tile product. I have been persevering in the idea that I am always afraid that it will be safer not to leave seams, and I don't know if you agree with my suggestion?

As we all know, in some areas in the southern part of our country, the temperature difference in the four seasons of the year is not large, not like most places in the northern region can reach 30 degrees Celsius in summer, and can reach minus 20 degrees or even degrees in winter, so the temperature difference is particularly large. The temperature difference is a simultaneous factor that leads to the expansion and contraction of this tile, and the temperature difference is small, and the amount of ceramic tile is small; If the temperature difference is large, the expansion and convergence of this tile will be large.

Therefore, like the vast majority of areas in the southern region of our country, there are many such seamless splicing tiles. Because of this temperature, the expansion and convergence of this ceramic tile are not large, and this provision can also be reached, so it is generally impossible to occur the hollowing, cracking, and warping of the wall commonly used in the northern region.