How to weave beads?? Bead weaving video tutorial

Here's a tutorial for hand-weaving beads:

Materials Tools: ropes, lighters, bells.

1. And the noise is pierced into the bell first.

2. Tie a snake knot.

3. After tying the snake knot, add the second thread.

4. Cross the light green line, that is, clamp the cracked red line, clamp it, and then cross the pink line left and right, repeat this method, that is, the four-strand braid weaving method, and weave it to the appropriate length.

5. After completing to the appropriate length, burn the pink rope, and then press and hold it to fix.

6. Then repeat the above steps, and the production of the lining needs to be left at the bottom.

7. Finally, use the remaining pink rope to weave a flat knot, and burn the glue to the end. Leave the light blue rope at the appropriate length, and then braided the end of the phoenix tail knot at the end, which is to repeat the previous operation. As shown in the image, this is done.

The bead hand weaving tutorial is as follows:Preparation tools Ingredients: bracelet thread, beads.

1. First of all, you must take a long enough bracelet line, which is three meters long. Fold the line in half and pinch the fold with your left hand.

2. Wrap one of the two threads pinched by your left hand around your left index finger.

3. Then remove the small circle and pinch it with your fingers.

4. Wrap another thread around your left index finger.

5. After winding from below, pass through the small circle that was wound for the first time, and tighten the line that was wound for the first time.

6. Use the same method above to continue to compile backwards, pay attention to the tightness must be even, so that it will be more flat.

7. As shown in the figure below, the bracelet is knitted to a certain length, and it can be placed around the neck to determine the desired length.

8. Take a beautiful bead and thread the bracelet through the bead.

9. Then tie a knot on the tail to complete.

1. Material preparation: foam board, pin, pin cover rope, beads, scissors.

Operation steps: 1. Position the rope as shown in the figure, and then fix the rope with a pin.

2. Put the rope on the right to the left on the rope in the middle, put the rope on the left on the rope below, cross the rope on the top, pass through the hole on the right from bottom to top, and then tighten the rope on both sides.

3. Repeat the previous step in the opposite direction. Place the left rope to the right on the center rope first, and then place the right rope on the lower rope. Finally, cross the rope at the top and pass through the world hole on the left from the bottom to the top. Pull the rope on both sides so that a flat knot is braided.

4. Weave a flat knot at one end, then put on a bead, and finally use a crochet to hook the rope on the left and right sides into the flat knot at the end.

5. In order to make the bracelet flexible, we also need to stack the ropes at both ends together, and then add a rope in the middle to weave a new flat knot.

<>2.1. Prepare a red rope.

2. Leave a little space at the bottom of a red rope and weave a bent flat knot.

After weaving, burn the thread with a lighter.

3. Burn the other end with a lighter. Wear your favorite beads.

4. Tie a knot with another rope at the bottom of the beads and weave a flat knot as long as before.

5. Knit it.

Ready to wrap up. Fold the two ropes in half.

Braided flat with another knot, and cut off the remaining thread. Flatten with a lighter.

7. Wear beads on each of the two red strings. Knot. The beaded bracelet is knitted.

Weave a simple bracelet. It only takes ten minutes. Add some fun to life. Knitting when you're bored can also pass the time.

Tools Raw Materials:

Red string. Beads, lighters.

1. Prepare a red rope.

2. Leave a little position at the bottom of a red rope and weave a bent flat knot. After weaving, use a Min stupid lighter to burn the thread.

3. Burn the other end with a lighter. Wear your favorite beads.

4. Tie a knot with another rope at the bottom of the beads and weave a flat knot as long as before.

5. Knit it. Ready to wrap up. Fold the two ropes in half. Braided the knot with another knot, and cut off the excess thread. Flatten with a lighter.

<>6. Wear beads on two red strings. Knot. My beaded bracelet was knitted.

Preparation for weaving: two ropes, three bracelet ornaments and two transfer beads.

1. Find a rope, fold it in half, weave a double connection, and don't pull it tight.

2. Take another rope, fold it in half, stuff it into the knot, and tighten the knot.

3. The two ropes in the middle are knotted twice.

4. Swap the two ropes next to you to the middle, noting that one is changed from below and one is changed from above.

5. Replace the two ropes in the middle and weave the snake knot twice. Repeat step 4 all the way around and string the transfer beads on the string.

6. Braided to a sufficient length, braided the two ropes on the side into a double connection, tucked the middle two into the knot, cut off the two excess threads in the middle, and then braided a button knot, cut off the remaining thread, and burned it with a lighter or match to make the knot of the rope stronger.