How to solve the broken grain elevator?

I can only buy a new one, no way!

Oh. The seed crushing is over, and we do it for the seed company, which is more demanding. If your machine is broken, simply find a manufacturer to repair it.

It will do the trick with some small crushing machinery and equipment.

Shandong Shanyuan crusher, professional crushing machinery and equipment!

Table 12 Common faults and troubleshooting methods of bucket elevator Causes Solution: Serious blockage 1The feed is uneven or the advanced material is driven after 2Bucket belt slip 3

The feed flow (including excess recycled material) exceeds the conveying capacity of 4There is a large piece of foreign object entering the frame 1No-load start, the feed must be uniform 2

Tension the bucket belt 3Control the feed flow 4Parking clearance and enhanced road clearance.

Table 12 Common faults and troubleshooting methods of bucket elevator (continued)-1 Fault situation Cause Solution: Excessive recycled material 1The belt speed is too fast or too slow2The gap between the discharging baffle and the bucket is too large3

The discharge port is not smooth 1Adjust the spindle speed 2Adjust the gap between the baffle and the bucket 3

There is an abnormal sound in the equipment of dredging the discharge port 1The bolts of the bucket are loose, and the bucket is damaged and falls off 2There is a foreign object entering the machine3

The gap between the bucket and the baffle is too small to cause an impact4The bucket belt is too loose or deviates, and the bucket hits the barrel 1Open the access door, tighten the bucket bolts, and replace the detached and damaged bucket 2

Stop the machine and remove the foreign body in the machine3Open the machine head and adjust the position of the baffle 4Adjust the tension bolts to tension the bucket belt and eliminate mistracking.

Solution to insufficient material discharge:

1. The capacity of the rear mechanical equipment of the bucket elevator is small, which makes the discharge chute blocked, and improves the production capacity of the rear mechanical equipment.

2. If the discharge port chute is too small or the chute angle is not suitable, correct the discharge chute.

The first thing to see if the raised grain is overweight? Then check whether the empty load selected by the hoist circuit is smaller?

The grain elevator does not know if you want to buy it or how.

The grain hoist you need is not to say that it can only be used to improve the grain, just that the grain is a material that can be promoted, formally because you may need to contact other manufacturers when they tell you that this is the grain hoist may be in the middle of the production or how, can only be used to lift the grain, but this is also impossible.

Therefore, if you need a hoist, we will tailor it for you as a machinery manufacturer that has been manufacturing bucket hoists for more than ten years, and ensure that the use and output meet the standards.

Why? Want to buy? Jiangsu Liyang Longjie.

In the normal operation process of the bucket elevator, the material is generally lifted from the bottom to the head, and the material is discharged from the discharge port, but some materials will not be very smooth when the discharge port of the elevator is discharged, and the different attributes of the material determine the smoothness of the discharge, and the way of discharging different materials is not the same.

Generally, the materials lifted by the material hoist are powder or granular, but some materials will have a certain amount of moisture, which makes the materials more humid, and will be bonded to the hopper wall during the lifting process, and will be discharged uncleanly when discharging, resulting in a part of the materials will be piled up at the bottom of the equipment. If it is a material with strong viscosity, then it is necessary to adjust the speed of the equipment faster, increase the power, and adopt a centrifugal discharge method, so that the material will not be bonded to the hopper wall and can be discharged smoothly.

According to the hoist manufacturer Tiantai conveying the bucket loss of the annihilated hoist bucket layout is sparse, the running speed is high, and the material flows into the bottom of the tail along the chute from the inlet port, which is easy to accumulate. The bucket rotates upwards to dig the material at the bottom with the rotation of the tail wheel, and the grain pile at the bottom is squeezed by the bucket in the excavation process, resulting in extrusion and crushing. When the bucket is filled with materials and continues to rotate, the material outside the bucket rubs against the bucket and the inclined deflector plate at the tail of the machine, resulting in friction breakage.

When the bucket runs to the upper part, the material collides with the threaded part of the bucket and the bolt head of the bucket, and at the moment of impact, the corn kernel collides with the high-strength bucket, and the sharp angle of the thread is cut, thus forming crushing.

Reciprocating hoist, continuous lifting.

Shafts and inclined shafts of non-explosion-proof and explosion-proof coal mines, metallic mines and non-metallic mines are used as lifting ores, materials, machinery and personnel; It can also be used in ports, wharves, slopes and other engineering construction sites, as a hoist. There are two types: AC drag and DC drag.