-
Radiator leakage generally do not repair, replace the best, because the radiator is a high pressure, high temperature resistant equipment, manual maintenance of this equipment will leave potential safety hazards, you only repair the surface leakage, the internal reason you can not see, in case you are not at home leakage will cause you greater economic losses.
-
Or find someone to weld and plug it! ~
-
If the radiator leaks, you can only find the manufacturer to replace it with a new one.
-
The repair method of radiator leakage is as follows:
For the slight water seepage phenomenon (about five drops per minute), the user can use the water connection appliance to receive water, and the water seepage may be reduced as the water supply temperature rises. More than 10 drops, it is a phenomenon of water seepage, according to the actual situation, observe for a period of time, about three to five days.
If the water seepage phenomenon is reduced with the change of temperature, the user can use the water connection appliance to receive water, and if the water seepage is serious (more than 10 drops per minute), the relevant units should be contacted in time for maintenance.
If the heating leaks, the situation can be differentiated: when the radiator leaks, if there is a valve in front of the radiator, the user should immediately close the valve to control the spread of the water accident. At the same time, immediately contact professionals for emergency repair.
When there is no valve in front of the radiator, the user first controls the spread of water, such as using water appliances to connect water, etc., and immediately contact the relevant units or professionals. When hitting, the address, contact and fault phenomenon should be reported in detail, so as to facilitate timely repair. The first step is to look carefully for the leak.
If there is a leakage in the installation of the radiator, after you close the valve, you can find the installation team to deal with it; If it is under warranty, it can also seek compensation; If the radiator is leaking, you need to contact the seller to consult about replacing the radiator, but it is generally within the warranty period.
If your community belongs to the old-fashioned heating system, you need to contact the property in time to close the main gate, and then find the heating unit to deal with it in time, otherwise it will not only cause losses due to water leakage, but also affect the heating of other users in the community. The losses caused by radiator leakage here are all things that everyone does not want to happen, but sometimes they cannot be avoided, and the losses caused are really a headache.
-
1. In most cases, the phenomenon of water leakage and dripping of the radiator is caused by the seam of the radiator, and with the growth of time, the leather cushion at the seam is easy to age, which will cause water leakage.
2. In this case, you can remove the leaking radiator, wrap it with raw tape, and then reconnect it, so that there is basically no water leakage, and it is also a way to cure the root cause.
3. If the leaking radiator is turned off, the room temperature will be reduced quickly, and it will soon be lower than the minimum temperature requirement of 16-18 degrees of the national standard. If you still want to live in this room, you should take emergency heating measures such as electric heating, air conditioning, and extra clothes or bedding to avoid freezing and cold.
-
1. If it is a trachoma leakage, you can use a bicycle inner tube, tighten it in the leaky place, wrap it around the trachoma one by one, and tie it tightly with a wire.
2. If the water leakage is serious, change to a PPR pipe, which is corrosion-resistant, heat-resistant, long-lasting, and cheap.
3. If the pipeline is complex and it is difficult to change the pipe, wrap the leakage with a raw meal belt, wrap it a few more times, and wrap it with aluminum foil outside, if the trachoma is not big, it can also be solved.
Clean with gauze paper: no oil. Water:
Then just glue it with AB glue! AB glue is another name for two-liquid mixed hardening rubber, one liquid is the glue, one liquid is the hardener, the two liquids can be hardened by mixing, and it is not necessary to rely on temperature to harden and mature, so it is a kind of hardening glue at room temperature, and it is sometimes used to make models. Generally used in industry. >>>More
The installation of kitchen radiators, in terms of material, the kitchen is suitable for choosing steel or copper-aluminum composite radiators, the choice of these two types is for heating considerations, they have a large amount of heat dissipation, rapid heating, open 15 minutes before entering, and when they enter, it is already warm like spring, which will not make people wait too long and avoid the pain of freezing; Second, because the kitchen is full of smoke and dust, the items placed in it are easy to accumulate dust, and it will be difficult to clean up if it is too late to clean for a long time, which requires the radiator installed in it to have a smooth surface and easy to clean and take care of. Among the many product types, steel and copper-aluminum composite meet the above requirements and are deeply loved by users.
It is possible that the reason for the small water pipe is that the water circulation is slow and the heating is not hot, the first group of heat is the front end of the water inlet and the second group of heat at the end will definitely be lower, you can change the pipe to a thicker point to accelerate the water flow and increase the heat.
Close the return valve. Before cleaning, in order to ensure safety, be sure to turn off all the return valves, and then use a wrench to gently unscrew the plug on one side of the radiator by hand. Here is a warm reminder for everyone: >>>More
To avoid rust, first of all, remove it from the rusty environment, in order to make radiators. >>>More