How to make a chair cover The process of making a chair cover

In the past, people used to buy chair covers, but now many people will make their own chair covers at home, so what is the process of making chair covers? Let's take a look.

Measure the size of each small piece of the chair first, convenient for cutting fabric, of course, the size should be 5 cm more than the actual size, so as not to be nervous when sewing, so as not to reduce the size of the finished product in the end, the tool may be very simple, maybe a pair of scissors, a piece of powder, a tape measure can be, this is a simpler tool to make a chair cover.

After measuring it out by yourself, you should make a draft drawing, cut the size according to the draft drawing, and sew each corresponding square together, to put it simply, sew it into a set little by little, and make your own chair cover including cushions, cushions, pillows, coffee table tablecloths, dinner tablecloths, table flags, etc. Then you only need to do some small processing and check the details, and then tidy up and check and tinker. Once there are no problems, the chair cover is done!

In fact, it is not very difficult to make a chair cover, you only need to do it in the details, and you must also mark the sketch where it should be marked, and the size must be accurate, otherwise the effect will not be good. Friends who like to engage in small household arts still have questions about how to make chair covers or other small furniture, so you can practice more.

The above is the chair cover production process I introduced to you, I hope it can give you some help.

How to make a chair cover, don't throw away old clothes, make it into a chair cover to save money and be practical.

Preparation materials: old clothes, fillers, scissors, needles, thread.

<>6. After the chair cushion reaches the expected softness, start sewing the opening of this end, which can be sewn by the Tibetan needle method, the flat needle method, and the back needle method, as shown in the following figure

7. Sew the open completely, and you can see that a soft chair cover is complete. As shown in the figure below:

The chair cover is made as follows:

Preparation materials: cloth, cotton, scissors, rope.

Operation steps: Step 1: Prepare two pieces of round cloth with the same face as the chair, the same size and the same suit, a large piece of sandwich cotton, two cloth belts of the same length as the circumference, a rope with the same circumference, and a green cloth strip.

Step 2: Cut the sandwich cotton cloth of the same size as the plaid fabric, stack the plaid cloth - sandwich cotton cloth - plaid fabric in order, fix the position with a pin, and sew the sealing cloth feet. One strip of cloth is stacked with a plaid fabric-sandwich cotton cloth, fixed with a pin, and then sewn to seal the cloth foot.

Step 3: Wrap the rope around the green strip of cloth, fold it in half, and sew it onto the top of the round fabric. Fold the excess part of the green strip of fabric in half on the outside of the seam and sew it onto the fabric on the back, otherwise it will affect the line of the strip below.

Step 4: Fix the processed strips of fabric in the second step face to face with a pin on the processed round fabric, and then sew two pieces of fabric. When stitching, remember not to sew too deeply, otherwise the round fabric will become smaller and will not fit into the chair.

Step 5: The prototype of the chair cover has been basically completed, and the principle of not exposing the stitches is followed. The other strip of cloth is made of lace by folding and sewing at the same time, so there is no need to make a sandwich surface here, otherwise the chair cover will become too heavy.

Step 6: The long strips of fabric on the edge of the lace and chair cover are face to front, and the strips of fabric and the chair cover are sewn together. After sewing, the front seam is added to fix the position of the lace, so that the lace can be more natural and beautiful.

1. Proofing with non-woven fabric according to the original condition of the chair and start measuring the size.

2. Cut the thickness and lace of the side, the front and rear length of the side has just been measured, cut according to the size, the height is arbitrary, and it is determined according to the appearance. The proportion of lace is doubled, and a strip is added to the reverse side of the side thickness for fixing.

3. The bottom edge of the lace should also be edging, and the thickness of the side should be piping.

4. Then combine the side thickness and face, and the lace part-time job fold is more beautiful, of course, you can choose the way you like to discount.

5. In order to be more perfect, we press the line on the front and install the narrowest presser foot in the world, and the line is relatively thin.

6. The chair cover is basically completed, and then an elastic band is added to the fixed tease Zheng Dingtiao on the thickness, so that the corner of the chair can be buckled and will not slide. Such a stool cover is ready.

Benefits of the hood:

1. Dustproof and anti-fouling.

Many people buy a new chair and go home with a cover on it. One of the advantages is that it can effectively prevent dust and stains, even if there are dripping coffee, red wine stains or even oil stains, they can be directly removed and cleaned, without affecting the material of the chair itself, and there is no possibility of bleeding, which is very convenient to clean.

Second, high comfort.

If you are using a solid wood chair, the sitting feel may be on the stiff side, so the comfort is more limited. However, if a soft and thick cover is applied to it, it can transform the hard texture into softness, and it will feel more comfortable to sit.

Household chair covers need to look at the material, color, pattern and **, of course, you can also make your own.

In order to keep the chair clean and beautiful after a long period of use, most users will use the chair cover cover protection, especially in the hotel, we often see many chair covers, the style and color are very eye-catching, of course, there are many people in the family who use it, and more and more people choose to make their own chair covers. Here's how to buy the right cover and how to make it.

Look at the materialWhen buying, you must first consider the material. Because its main function is to prevent dust and protect the surface of tables and chairs, try to choose some hard-wearing and easy-to-clean fabrics, such as chemical fiber materials, which are very light and thin, and at the same time very durable.

Look at the color and the choice of color is also important. Pay attention not only to aesthetics, but also to the overall style of the match. For example, white represents natural purity, orange represents brightness and warmth, etc. Each color has its own unique charm. Choose what you like, as long as it's too fancy.

The pattern of the chair cover should be simple and simple, so that it will not be too abrupt in the room. For example, the plaid pattern will look warmer, and the flowers and plants will be more casual and natural.

Look**Since the chair cover is mostly fabric, it will not be too expensive. Most of the ** for ordinary materials are between 20 - 100 yuan, and the ** for fine high-end materials is between 100 - 500 yuan.

1.Materials: a thick cloth, scissors, a measuring tape, chalk.

2.Measure the size of each area of the chair first, so that it will be more comfortable to cut. Of course, it is necessary to cut 5cm more than the actual measured size, so as not to reduce the size of the chair due to tension during sewing.

3.Then make a sketch based on the measured dimensions, then cut and finally stitch the corresponding corners to form a simple chair cover.

You can choose some chair covers that are easier to wash, so that they are easy to wash when they are dirty, as long as you have this skill, you can do it.