What s the matter with the smoke prisoners who don t like to smoke?

The ondol chimney doesn't like to smoke. It may be that there is too much ash in the kang. Dispose of the ashes in the kang. Then dig out the chimney and the ash at the bottom. Then he took a long stick and went up to the house and threw the chimney. So the chimney has cramps.

It's going to burn well.

There are several reasons: 1, there is a tree above the chimney 2, the chimney position is lower than the house next to it 3, the chimney root and the stove mouth are not set up windward bricks These three are the reasons that affect the smoke, and there are small pumps for special smoking in the bazaar, which can be installed at the mouth of the chimney, effectively improving the situation of not liking to smoke.

There are several reasons for this:

1. There is a tree above the chimney.

2. The chimney position is lower than the house next to it.

3. There are no windward bricks at the chimney root and the inner mouth of the stove.

All three of these are the causes of smoke, and there are small pumps for smoking in the bazaar, which can be installed in the chimney mouth, which can effectively improve the situation of not liking to smoke.

The smoke of wormwood is smoky, what to do? Many moxibustion enthusiasts will have such problems.

The first is that we have to choose high-quality moxibustion strips, the year is heavier, his smoke will not choke, inferior moxibustion strips smoke is very large, choking people shed snot and tears.

The general choice is more aged wormwood, and its smoke is purer and lighter!

The second is that we need to make a set of smoke exhaust equipment and open the windows for ventilation.

Or maybe the door allows the air to form a convection current to dilute the smoke in the room!

Like some professional moxibustion halls, there are relevant smoke exhaust equipment.

The smoke from the fire is generally the hot smoke produced by the fire that does not go out down the chimney, but pours back into the kang hole. There may be several reasons for this situation, one is that the inner diameter of the chimney becomes smaller (hanging with more soot and tar), and after cleaning, the inner diameter will be restored to the same height, and the resistance will be smaller, which will benefit the rapid rise of hot smoke; The second is that there are gaps on the surface of the ondol, which may also cause smoke to come out of the gaps.

Since the dust accumulation of the air duct caused by long-term combustion, it is necessary to first check whether the main air duct is blocked, and it is necessary to pay special attention to whether there is a large amount of dust accumulation in the throat part in the direction of the fire kang.

It may be caused by insufficient height, you can choose to extend its height, it will be better to reach about 5 meters, it must be higher than the backbone of the house, so that there will be a lot of pumping force. There may also be a problem with the kang, which was not tightly blocked when it was built, and there was a place for air leakage. You can recheck it, plug it with something, or you can build a new one.

Summary. Reason: The basic use of the rural kang is corn stalks, peanut vines, etc., when burning in the pot stove, the grass ash will be sucked into the kang hole with the flames, and after a long time, it will be blocked, resulting in smoke from the soil kang.

Solution: Dig out the dust with a small hoe with a long handle to solve this problem.

The kang is not good to burn, what to do if the kang smokes.

Reason: The basic use of the rural kang is corn stalks, peanut vines, etc., when burning in the pot stove, the grass ash will be sucked into the kang hole with the flames, and after a long time, it will be blocked, resulting in smoke from the soil kang. Workaround:

A small hoe with a long handle can solve this problem by scooping out the dust.

Reason: Smoke from the earthen kang and clogged chimney are also one of the reasons. Solution: This needs to pass the chimney, and when the chimney is passed, the soil kang will not smoke.

Both of the above reasons can cause this issue.

Summary. Check whether there is any blockage in the main air duct, especially the throat area where the fire kang is going. It may also be blocked by mud from the ondol to the final exit of the wall of fire.

The stove should not be too high, the flue should not go too far, and the bottom of the smoke outlet of the fire wall should be built with two bricks to form a gradual slope, which is conducive to the upward movement of the wind.

Check whether there is any blockage in the main air duct, especially the throat area where the fire kang is going. It may also be blocked by mud from the ondol to the final exit of the wall of fire. The stove should not be too high, the flue should not go too far, and the bottom of the smoke outlet of the fire wall should be built with two bricks to form a gradual slope, which is conducive to the upward movement of the wind.

Hope it helps.

Look at the one above.

What's the matter with pouring smoke.

Hold on. How to fix it.

How to fix it. If the kang is not good to burn, you need to put a brick on the chimney to prevent the gas in the chimney from not circulating, or check whether the root of the kang is blocked, if it is blocked, you need to clean up the internal dust, and the height of the chimney should be greater than the ridge to avoid wind backflow.

It may be that the chimney has a small pumping force, and the chimney can be heightened, and the pumping strength is proportional to the height.

It may be that there is a narrow part of the flue that can be remodeled or rebuilt.

It may be a problem with the wind direction, put a brick on top of the chimney to block it and try to see the effect, it is best to install an induced draft fan, the effect will be very good.

It may be that there has been no ash pumping for many years, causing the chimney and the root of the kang to be blocked. Find a professional to use a powerful exhaust fan to clean the lower chimney and the root of the ondol.

There are techniques for doing everything, and there may be two reasons for your problem, 1The top layer is too thick. 2.

The middle of the kang was too smooth, and a large amount of hot gas was discharged along the flue. You try to plug the mouth of the chimney a little smaller, the size should be appropriate, be careful of gas poisoning, if it doesn't work, you have to rework, and make a new ondol.