-
Press down on the plastic bullet on both sides, if you hear a crisp sound when pressing, it means that the slide is open.
1. The more traditional method of disassembling the drawer slide rail of the office computer desk can have several steps:
1. First of all, it is necessary to understand the overall structure of the drawer slide rail (different disassembly methods are different for different structures).
2. If it is determined that it is a common slide rail for the family, that is, a three-section track, a sheet metal slide rail. The cabinet should be gently pulled out first, but not upside down, and then carefully check whether there is a sharp object leaking on both sides of the cabinet, usually on both sides of the cabinet.
3. Then press the plastic bullet card thing on both sides downward, if you hear a crisp sound when pressing, it means that the slide is open.
Second, there is a kind of drawer is composed of five wooden boards (drawer panel, left and right side panels, back panel, thin board), this drawer disassembly method is:
1. Tighten the plug on the board, then screw on the long black screw, smash the white soft screw buckle into the corresponding air of the board, tighten the white screw buckle in the white screw, according to the label, find the corresponding tobacco control, black screw and board, stuff it in, the black screw is stuffed into the plug hole, and the small hole corresponds to a slightly larger round hole.
2. The slide rail is on both sides of the left and right side panels of the drawer, we first install screws on the floor of the drawer, and push the black circlip upwards on both sides of the side plate of the drawer, and the slide rail can be pulled out.
3. Then install the slide rail, which is fixed with a sharp small screw, and a slide rail is fixed on the cabinet with two small screws, one before and one behind, and the slide rails on both sides of the cabinet are installed in this way.
4. This drawer panel is generally with a card slot, and there are two small holes in the middle for installing the handle, and after the installation is completed, the stains on the countertop should be cleaned with a rag dipped in water.
3. Some precautions in the process of disassembling the slide rail of the drawer of the office computer desk (that is, to avoid damage to the slide rail):
1. When pulling the cabinet out, you must pay attention to the horizontal pull-out, so as not to cause damage to the cabinet and not damage the slide rail.
2. Then the buttons on both sides of the cabinet must be pressed lightly, if the press does not move, there is something stuck in it, and it needs to be checked and cleaned up before it can continue.
-
Under normal circumstances, the slide in the box is together, two, each is divided into two parts, divided into inner and outer channels, the inner channel needs to be fixed on the left and right sides of the keyboard extension board with screws, and the outer channel needs to be fixed with screws on the left and right sides of the computer desk to place the position of the keyboard carriage!
When the slide is disassembled, you need to hold down a small black plastic shrapnel at the end, and if you don't hold it, you can't separate the inner and outer lanes! There is also an order before and after the slide! Try it yourself when you install it!
The steps are as follows: 1. Move the small plastic sheet (usually black) in the middle of the marking to the side, and then separate the marking into two parts.
2. Put the part without balls (with small plastic sheets) on the drawer with wooden screws (pay attention to the direction);
3. Put a part of the ball (with marking) on the table with wooden screws (pay attention to the direction);
4. Move the small plastic piece (usually black) in the middle of the drawer railing to the side and push the drawer in.
-
1. First of all, remove the keyboard tray from the computer desk, and fix the fixed part of the slide on the back of the bracket with a nut.
2. Insert the screw into the sliding part of the track and snap it into one end of the fixed part, as shown in the figure below.
<>3. Snap the sliding part of the track into the fixed part. Seep dust.
4. Install the tracks on both sides of the bracket.
<>5. Finally, put the bracket back on the computer desk. The installation is complete.
-
Press the screw with your thumb of both hands, gently press down the black plastic, and easily pull it away in front of you after feeling it loose. (Knowledge repentance and extension) slide drawer disassembly: 1. Everyone pulls the drawer out as much as possible, and a long black tapered buckle appears.
2. Use your hand to put the black protruding strip buckle and press it down (in most cases, it is downward, not excluding lifting it up), and the strip buckle will be lengthened, and then I feel that the slide rail is loose. 3. At the same time, both sides press down the long strip before the buckle, and both hands press the strip buckle at the same time, and both sides pull out, and the drawer will come out and scatter.
-
The keyboard slide of the computer desk is a consumable, it is easy to be damaged, and we need to replace it in time, how to install the keyboard slide? I would like to share my own experience.
Buy a computer dust table slide on **, this example is the cheapest two-section track.
First, remove the keyboard tray from your computer desk and secure the slide fixing part to the back of the tray with a nut.
Sun Napi put the screw into the sliding part of the track and snapped into a bad head of the fixed part.
Snap the track slide part into the fixed part.
Install the rails on both sides of the bracket.
Finally, attach the bracket back to the computer desk.
You should now be able to install the keyboard slide!
-
If you can't see **, pull out the keyboard desk, and you will see a plastic spike, one on the left and one on the left, the left spike is broken up, the right one is broken down, and the table comes out as soon as you pull it.
-
Just use the Qizi to pull off the gong wires.
The height of the table top should not exceed 70 cm. Diseases such as low back pain, neck muscle fatigue or strain, hand tenosynovitis and vision loss are harming computer-related workers due to the poor design of computer desks. >>>More
Can you cut the glass of a computer desk? The glass of the computer desk cannot be cut. Because of the computer, the table glass is custom-made. You can't just change it. You can't change the song casually if you're a professional. If you are a professional, you can use it.
One of the most common ways to solve the problem is to find this [ch] on the right side of the desktop menu bar before opening the game, click on it, click to open the option box, we will find that "ch" stands for "Chinese", and all we need to do is switch it to [en], that is, English. >>>More
The capslk on the computer keyboard is the uppercase lock key. >>>More
The one on the second floor is obviously advertising for his company, which is very bad, so you have to be kind! Don't mislead consumers ... The 2nd floor is so popular on the mainland side. . . >>>More