Lenovo IdeaPad 310S Disassemble Lenovo IdeaPad 310 Notebook How to Disassemble and Replace the Batte

You can do this by following these steps:

1. Flatten the front of the notebook downwards and find the battery on the back of the notebook;

2. Find the battery compartment buckle everywhere in the battery compartment, pull the battery compartment buckle on the left side horizontally, and open the back plate of the battery compartment;

3. Remove the back plate of the battery compartment, and you can see a black square battery below;

4. Push the battery on the left side horizontally, remove the battery, and the operation is over;

The battery of this computer has a built-in non-removable design, so it is recommended not to disassemble it at will. If necessary, you can go to the professional maintenance department for disassembly. Since it is a built-in battery, it is not like an external battery that can be assembled and detached at will.

The built-in battery is pluggable or soldered, so special tools are required to remove it. The battery can better protect the power supply on the computer, and the power supply is more stable. It also plays a role in protecting the other hardware of the computer.

Therefore, to sum up, it is recommended not to demolish it privately.

The method is as follows: 1. Put the front of the notebook down flat, and find the battery ** on the back of the notebook.

2. Find the battery compartment buckle everywhere in the battery compartment, pull the battery compartment buckle on the left side horizontally, and open the back plate of the battery compartment;

3. Remove the back plate of the battery compartment, and you can see a black square battery below;

4. Push the battery on the left side horizontally, remove the battery, and the operation is over;

Summary. 1.First, use screws to remove the protective cover of the hard drive and memory. Because the hard drive and memory need to be easily removed, there is a separate protective cover, so there is no need to disassemble the whole machine.

2.Speaking of laptop memory, laptop memory is asymmetrical, and there will be a notch on the left. This groove is the alignment slot when the memory is installed.

3.After removing the protective cover, you can see the memory slot and the hard disk, by the way, the hard disk is removed, as long as the fixing screws of the hard disk are removed. Then push the drive out to the right.

Many people will disassemble and reload the original hard disk and replace it with an SSD, and use the interface of the optical drive to connect a hard disk, if there is an opportunity to introduce it.

4.There are two fixed clips in the memory, just pull it and then pull the memory up and out.

5.If it is a memory installation, insert the memory slot at a 45-degree angle. Note that the mount is aligned with the mount of the memory slot.

6.Once fully pushed in, press down on the memory. Then fix the card twice to fix the memory.

7.The memory sometimes has the problem of poor contact, and the gold finger can generally be wiped with anhydrous alcohol. Or wipe it with a clean eraser before installing, and then take care not to drip sweat on the memory, which is easy to burn the memory, and do not get sweat stains on the gold fingers.

How to remove the metal cover of Lenovo ideapad310s memory module.

Hello, I have seen your question and am sorting out the answer, please wait patiently for a minute.

1.First, use screws to remove the protective cover of the hard drive and memory. Because the hard drive and memory need to be easily removed, there is a separate protective cover, so there is no need to disassemble the whole machine.

2.Speaking of laptop memory, laptop memory is asymmetrical, and there will be a notch on the left. This groove is the alignment slot when the memory is installed.

3.After removing the protective cover, you can see the memory slot and the hard disk, by the way, the hard disk is removed, as long as the fixing screws of the hard disk are removed. Then push the drive out to the right.

Many people will disassemble and replace the original virtual hard disk with a solid state drive, and use the interface of the optical drive to connect a hard disk, if there is a chance to introduce it. 4.There are two fixed clips in the memory, just pull it and then pull the memory up and pull it out.

5.If it is a memory installation, insert the memory slot at a 45-degree angle. Note that the mount is aligned with the mount of the memory slot.

6.Once fully pushed in, press down on the memory. Then fix the card twice to fix the memory.

7.The memory sometimes has the problem of poor contact, and the gold finger can generally be wiped with anhydrous alcohol. Or wipe it with a clean eraser before installing, and then take it carefully, be careful not to drip sweat on the memory, easy to burn the memory, and don't get sweat stains on the gold finger.

Step 1: Preparation.

Prepare the tools (fine Phillips screwdriver, flathead screwdriver, tweezers, blade, soft cloth) and the notebook to be disassembled.

Step 2: Remove the battery.

With the back of the laptop facing up, open the battery's retention latch and remove the battery.

Step 3: Remove the back guard.

Disassemble the fixing screws of the two guards on the back of the notebook and remove the guards.

Step 4: Remove the hard drive.

Unplug the hard disk cable and take out the hard disk.

Step 5: Disassemble the NIC.

Gently pull out the network card from the data slot, gently pry open the metal clip of the power cord, and take the network card out.

Step 6: Remove the buckle bar.

With the notebook facing up and the LCD screen on, gently pry open the upper buckle bar of the keyboard and turn it up, and then open the cable connected to the motherboard and take out the buckle.

Step 7: Disassemble the keyboard.

Gently pry the keyboard open and flip it up (be careful not to tear off the cable underneath), disassemble the cable, and remove the keyboard.

Step 8: Disassemble the LCD screen.

Disassemble the two cables between the LCD screen and the motherboard, including power and data, unscrew the display fixing screws, and take the display screen.

Step 9: Disassemble the touchpad.

Gently disassemble the cable connecting the touchpad from the motherboard and remove the main case of the touchpad.

Step 10: Disassemble the optical drive, etc.

Remove the fixing screws and remove the optical drive, heatsink and fan on the back.

Step 11: Disassemble the motherboard.

Unplug the sockets of the cable and the next cable, and then pay attention to the cable below when removing the motherboard, and remove the motherboard and accessories.

Step 12: Disassemble the memory.

Gently push the memory module to the sides to secure the metal clip, the memory module will pop up, and then pull out the memory module.

Step 13: Disassemble the CPU

Release the metal clip of the CPU and pull out the CPU.