How to deal with the beam to be more beautiful? What are the easiest and most straightforward ways t

The beams can be directly exposed or a few more beams can be added, or the ceiling can be used to cover the beams; The easiest and most straightforward way is to expose the beams directly, which can show a natural top design, which is very beautiful and intuitive.

You can use a cascading ceiling, which is more beautiful and more beautiful, which is the most direct way to be more beautiful.

If the load-bearing beam is located in the middle area of the living room, it can be treated with false beam modeling, if the floor height condition of the house is better, the ceiling can be flattened, and the beam is incorporated into the ceiling so that the ceiling becomes a whole, if the floor height condition is limited, the ceiling will cause a sense of space depression, not suitable, it is recommended to beautify the beam, such as through the false beam modeling is very good.

How to deal with the beam to be more beautiful? What are the easiest and most straightforward ways to do this? My house is also being renovated now, and I am worried about the beams in the hall, and my eyes are still white and occupy the headspace.

As a result, the master took advantage of the beam! Punching holes in it to install air conditioning, still laughing at me, this beam is suitable for hanging air conditioning, I don't understand, air conditioning is usually installed on the wall, isn't it? What if it falls off the beam?

The host said it didn't matter, and the income was not bad! It's a great place to hang an air conditioner, but I'm worried it's going to fall off the beams! The owner said that there is no need to worry about it, because the beams at home are usually reinforced concrete structures, which are similar to load-bearing walls, and the load-bearing capacity is very good, and it is more than enough for hanging air conditioning.

In addition, the air conditioning hanging on the beam can avoid drilling holes in the wall, which does not affect the aesthetics, and can save trouble and reduce damage to the wall. In this way, the owner does not have to spend a lot of money to decorate the beams, and makes more reasonable use of the various spaces in the living room. The air conditioning on the beam is conducive to improving the utilization rate of air conditioning, as we all know, the air conditioning blown out by the cold air usually precipitates to the bottom of the room, that is to say, the hanging air conditioning, the higher the air conditioning in summer, the faster the indoor temperature drops, which greatly improves the utilization efficiency of air conditioning, and it can also reduce part of the electric energy.

Most people will have beams in their living room, but some owners can choose to install a suspended ceiling on the ceiling to serve as a cape decoration. But what if you crash into a house with a low ceiling? If you condolence and support again, it will make people feel depressed.

Therefore, it is advisable to install air conditioning on the beams to save space. Although it is said that only two fixed holes need to be drilled to install air conditioning on the beam, there are risks in drilling holes in the beam, so what should you pay attention to when drilling holes in the beam?

The master told me that as long as the steel bar is not hit, the stability of the beam will not be affected, thus avoiding the collision of the main reinforcement. If there is a beam, either the beam is used to act as a beam, or the number of beams is hidden. Frankly, you can expand the effect of the beam or reduce it to a minimum.

When it comes to magnification, you can make a beam around the ceiling, with the beam as part of the ceiling. Or with the help of beams, the division of a section of beams has a significant impact on both sides of the beam, or on the surroundings.

Scheme 1: Separate the space under the upper cover beam. In the design of the ceiling, a large arc can be used to weaken the beams with indirect lighting, so that the whole living room space looks tall and bright, and also allows different fields to have the most suitable conversion zone.

Scheme 2: Indirect lighting increases the sense of hierarchy. In the decoration of the space, through the design of indirect lighting, the visual beams in the bedroom space can be reduced, and the privacy effect of the white film glass behind the mirror wall can be multiplied, supplemented by the elevated design, which can also change the space with different functions.

Scheme 3: Incorporate a variety of design elements. Of course, if you don't want the bedroom ceiling to be too monotonous, then you can use glass, mirrors and other elements to add a sense of fashion, such as the black acrylic carved totem, which can add points to the bedroom space and weaken the vision of the beam.