Keyboard, what to wash it with?

To clean the keyboard, you can open the keyboard by disassembling all the screws at the bottom of the keyboard. (Some keyboards hide a few screws underneath the keys.) The purpose is to make the keyboard and conductive rubber contact better).

Remove the plastic foil. Remove the circuit board of the keyboard cable, do not wash it with water, only wipe it with alcohol. The connection between the plastic foil and the circuit board can be wiped with an eraser to wipe the black oxide layer clean, and then pour all the conductive rubber caps inside the keyboard into a basin with neutral washing liquid (dish soap can also be used).

The place where the plastic foil and the conductive rubber come into contact with the rubber should also be wiped clean with an eraser, which is the key point, and if you don't wipe it clean, the keys of the keyboard will fail. Then remember the position of all the keys on your keyboard, take off each key and pour it into the washing solution, each button is stuck with two small plastic clips, and you can remove it by pinching the clip a little hard when dismantling. After soaking for a while, you can scrub it with a small brush (a paint brush will do).

Soak the entire empty keyboard in the washing solution for cleaning. Wash and dry. Then put each key of the keyboard back in place, turn the keyboard upside down after installing the keys, and then put the conductive rubber caps one by one in the corresponding position of the keys.

Put on the plastic foil to connect the circuit board (pay attention to the connection between the circuit board and the plastic foil), and then try whether the feel of each button is very good after installing the screws, if it is not good, the installation is not in place. Skill comes from practice.

First of all, you must prepare the following things: a small screwdriver or a small iron rod or something like a flat mouth, a basin of water with a little washing powder, and one or two dry towels.

Step 1: Write down the keys on the keyboard to avoid making mistakes when you re-connect the keys after cleaning.

Step 2, use a small screwdriver or a small iron rod to pry out each key, pay attention to the force, do not use too much force, and be careful of the small spring under the enter key and some longer keys.

Step 3: Pour all the keys into the prepared laundry detergent water and soak for about 30 minutes (if you want to quickly or still have dirt that has not been removed, you can use a towel or something else that can be wiped one by one). Then dry with a dry towel.

Step 4: Use a wet towel (after wringing out the water) to wipe the dirt inside the keyboard, and be careful not to let the water from the wet towel flow into the key holes, so as not to cause the wiring in the keyboard to malfunction.

Step 5: Press the dried keys into the keyboard key holes one by one, and pay attention to the inversion.

Teaches you how to clean the keyboard.

Alcohol, when thoroughly dried!

Because the computer keyboard and mouse have the most contact with the user, and many computer users do not clean the display screen for several years, scrub the keyboard, mouse and other equipment, the surface of the computer user will often be stained with the sweat, oil, saliva, dust, hair and other dirt deposited in the keyboard, which hides a lot of germs, such as streptococcus. You see, if you work on such a keyboard all the time and forget to wash your hands afterwards, it will undoubtedly be detrimental to your health. Therefore, how to clean the keyboard becomes very important.

Use a screwdriver to unscrew the screws on the back of the keyboard, it should be noted here that some keyboards do not open the keyboard by unscrewing the screws on the back of the keyboard, and there are 2-3 screws under the keys on the front of the keyboard, and some of the keys need to be pried off the keyboard to see the rest of the screws. Unscrew it and we'll be able to open the keyboard. We can remove each key on the keyboard so that it can be cleaned sufficiently.

After the keyboard is disassembled, we will find that in fact, the circuit part of the keyboard is still very clean and does not need to be cleaned, mainly because the keys and the front panel of the keyboard are dirty, and we only need to clean these two parts. Put the keys and the front panel into the washing solution for cleaning, sometimes the dirt of the keyboard is easy to clean, but sometimes because of the long-term use of the keyboard, the keys are aging and yellow, it may not be easy to clean, you can put the keys in the detergent for a period of time, the effect will be better. After washing, let it dry for a few hours, or use a hair dryer to dry the keyboard and install the keyboard as it is.

It should be reminded that some large keys have reeds, and you should install the reeds when you install them, otherwise the keys will be damaged if you use them for a long time.

Resources.

It is better not to wash the keyboard. It is best not to rinse the keyboard directly with water, although it can be cleaned more cleanly, it is easy to clean the letters on the keyboard. Whether it is a keyboard on a notebook or a keyboard that is usually used, try to wipe it with a rag to avoid leaving water inside the keyboard and affecting the normal use of the keyboard.

Keyboard cleaning precautionsOnce the cleaning is complete, allow the cleaned keyboard to dry for a few hours or use a hair dryer to dry, then install the keyboard as it is. When installing, you should first put the panel facing down on the table, put the two sides with book pads, and then put the small rubber pads into the buttons one by one, then put the circuit board and bottom panel, and finally put the screws, and then you are done.

If it is a special notebook keyboard film, that is, a keyboard film that matches the keys and models, the cleaning principle is the same. Wash it in the same way and spread it in the air, but remember not to pull it in the sun, otherwise it will deform quickly and shorten the life of the keyboard membrane.

1. In order to clean the keyboard thoroughly, first find a cloth, the cloth must be soft, so as not to rub off the words of the keyboard and damage the keyboard, wet the cloth with water, and then dry it slightly, fully wash the keyboard, and not use a too wet cloth, because if the water enters the gap under the keyboard, it may cause damage to the circuit.

2. Squeeze a ball of toothpaste, about twice as much as usual brushing, part of it is applied to particularly dirty keys, and one part is applied to a moist and dry cloth, and then use a cloth to scrub the surface of the keyboard clean, and the part can be wiped for a longer time.

3. Squeeze a ball of toothpaste, about the usual amount of brushing, put it on the palm of your hand, dip a little with a toothbrush, brush the side of each key of the keyboard, and press the key next to it to brush the particularly dirty place, and brush it with a toothbrush until it is clean and satisfied.

4. After the keyboard keys are cleaned with toothpaste, there will be a lot of foam and dirt that is difficult to be removed, which is a very important process, scrub with a toothbrush dipped in water, which is combined with a cloth, the cloth should be scrubbed clean and dried, and the dirt brushed out will be wiped away.

Among the computer accessories, the number of keyboards is the most likely to be dirty, especially the keyboard of desktop computers, under normal circumstances, we may use a brush to brush between the keys. But in fact, the entire keyboard can still be cleaned with water, tool: keyboard.

A screwdriver or a slotted screwdriver.

Laundry detergent sanitizer basin cloth.

02、、Disassemble the panel from the back of the keyboard after disassembling the key:

Please click Enter a description.

03. Carefully remove the keys and circuit boards

Please click Enter a description.

04. Okay, use Mr. Mighty to clean up the dirt on the keyboard, and brush the keyboard case with a brush:

Please click Enter a description.

05, and these keys are rising, soak them with laundry detergent and wash them clean:

Please click Enter a description.

06. Then dry the keyboard case and keys after cleaning, and finally install the keys and circuit paper back into the keyboard case with a few holes

Please click Enter a description.

07. Press some keyboard buckles into the corresponding positions:

Please click Enter a description.

08. There is also a circuit board that is installed in the appropriate direction

Please click Enter a description.

09. This kind of circuit board will have directional buckles and screws

Please click Enter a description.

10. At this time, we can not be in a hurry to install the keyboard screws, but insert it into the computer first to test whether the keyboard can be lit and whether the keys can be used normally. Note that the PS 2 keyboard is not hot-swappable with electricity:

Please click Enter a description.

11. Tighten the keyboard screws when the keyboard can be used normally

Please click Enter a description.

12. There are still keys that need to be put back. I forgot the key position and installed it on the Internet:

Please click Enter a description.

Precautions: Be sure to pay attention to the direction and skills when disassembling the keys;

It is recommended to disassemble from the bottom row of keyboards;

For example, it is not recommended to disassemble large keys such as the enter keyboard and the space bar;

It is recommended to take a picture of the keyboard before disassembling it to facilitate the installation later.

Keyboard cleaning brushes can be used with dish soap.

Cleaning. Then put it in a ventilated place to dry in the shade. Alternatively, you can use a mild laundry detergent or baking soda if it's particularly dirty.

Soak it in water and then wash it, and you can take care of it very cleanly. Let's take a look at how to clean your keyboard.

I believe that the vast majority of families have one or many computers, then there will be a lot of keyboards that need to be cleaned, if used for a long time, there will be holes and a lot of dust accumulated on the keyboard.

Especially in the gap between each key, there is often a lot of dust, too much dust accumulation affects the feel, and will reduce the service life, many expensive keyboards are often due to the accumulation of dust and the service life is particularly short, and there is often a problem that the keys are not well matched.

In order to solve this problem, we often buckle all the keys, but this is particularly troublesome, and it is not easy to install it back, in order to clean some people use a brush, but it is not easy to clean, it will be very clean when washed with water, but water will damage the keyboard, so I do not recommend everyone to clean with water.

Clean with a hair dryer, we only need to deduct the "backspace" key and "ctrl" on the keyboard, this action is very simple, gently pick it down, and then we will stand up the keyboard diagonally, and then blow it with a hair dryer at the key that is buckled from the top end, and then gradually blow down from the top end. Then the dust will come out from underneath and it's as simple as that, and all the dust will be cleaned up.