How do you remove a spherical lock cylinder? What is the ball cylinder installation method?

Lock installation learning and ball lock installation.

Turn the spherical handle clockwise or counterclockwise to the limit position, and you'll see that there's a pin in the notch, and you can pull the hand off by finding a sharp thing to push it down, and then it's very simple.

<><3. You need to unscrew the decorative cover of the ball lock again, find the two screws on the door on the ball lock, and remove the screws.

Ball removal steps on the outside of the spherical lock:1. Use the iron piece attached to the ball lock fitting to remove the handle and insert it into the small hole under the handle.

2. Follow the previous steps and the handle can be easily unscrewed.

3. Tie the latch in the small hole on the side of the door panel, press down on the latch so that the protruding part is stuck in the notch, and turn the door handle to ensure that the latch is well connected with the lock.

4. Install the ring, tighten the screws, turn the door handle after tightening, confirm that the ring is correct, and install the rear door handle.

5. Fix the bayonet of the door hole of the screw box on the bolt, and try not to lock the door after installation.

6. Use an electric screwdriver or Phillips screwdriver to remove the locking bolts.

1. Find the small hole of the spherical door lock, find a slotter and insert it into the small hole.

2. The spherical door handle can be removed by installing the above method.

3. Twist the decorative ring a few times and remove the decorative ring.

4. When you see the two fixed screws, loosen the screws with a screwdriver, and then gently pull out the spherical door lock from the outside.

5. Use a Phillips driver to loosen the deadbolt screw, and you can easily take it off. At this point, the spherical door lock is disassembled!

Is it to change the lock or remove the cylinder? If you change the lock, there is a small hole in the rod between the two balls, poke it down with something, and the ball on one side can be pulled off, and you can install the door up, it is very easy, don't remove the lock cylinder! If you want to disassemble the lock cylinder, then open it to see the shape of the iron sheet inside, you can judge its function and position, and be careful that there is a spring inside.

The question is how do I press these parts back now.

1. Use the spherical lock accessories with an iron piece specially designed to remove the grip and insert it into the small hole under the grip.

2. Follow the previous step to easily unscrew the grip.

3. Use a slotted driver to pry up the gasket behind the grip.

4. Use a Phillips driver or electric driver to loosen the fixing screws in the ball lock.

5. Take out the old spherical lock from the other side of the spherical lock.

6. Use an electric screwdriver or a cross driver to remove the bolt.

Lock installation learning and ball lock installation.

You will observe the spherical lock, the front of the keyhole is outside the door, the other end is the door, the end of the door near the back cover where there is a small hole, there is a protrusion inside, you take a small screwdriver to push the protrusion inward, and at the same time the spherical object back back, you can remove the back ball, and then reverse twist the back cover, and remove it, and then you take a Phillips screwdriver to unscrew the round spacer, so that you will just open the spherical trivial disassembly! Now you can start to install the lock: you put the tongue of the lock (that is, the cylindrical object on the top of the box on it, and there is a square iron sheet with two holes on the top of it) into the hole on the side of the door, and then take the ball in front of it in your hand, and put the other end in the hole outside the door and stuff it into the room, and at the same time make the gap in the lock body align with the fork behind the lock tongue, and then buckle the round gasket after stuffing it into place, and tighten the screws, then screw the back cover, and finally, align the back ball with the lock and push it on. When pushing up, you should also turn it slightly clockwise, and remember that there is also a small gap in the back ball, and you should aim it in the direction of the small hole with a protrusion!

Now screw the two screws on the deadtongue on the side of the door, okay, the task is complete, and there is no need to change the outer frame of the door.

In our home renovation, the toilet door is generally installed with a ball lock. So if there is a problem with the spherical lock and it needs to be replaced, do you have any better methods? Nowadays, people often ask about the replacement of the spherical lock, and then I will talk to you about how to remove the spherical lock and what are the specific steps.

How do you remove a spherical lock cylinder?

At present, what do you need to pay attention to when dismantling the new spherical lock? Tool components to be prepared: cordless electric screwdriver, screwdriver, ball lock assembly, using the ball lock accessories attached to the special removal of the grip of the iron plate, inserted into the small hole under the grip.

Now that you're ready to disassemble, remember to disassemble from the inside out. First find a small hole in the lock on the inside of the door, this key guess is the most critical step to remove. Use a slotter or wire to insert into the small hole.

This makes it easy to remove the inner ball door handle. This is one of the ways to dismantle the spherical lock cylinder.

The next step is to remove the decorative ring of the spherical door lock, because the decorative ring is fixed with movable wire, so you can remove the decorative ring as long as you twist it a few times, and you can also refer to this method.

What is the installation method of the spherical lock cylinder Huyan?

One of the methods of installing the spherical lock cylinder: first of all, it is necessary to open the hole in strict accordance with the opening diagram to install the size, if the hole is too small, it is easy to cause the door lock and the circuit board to extrude and deform, resulting in the completion of the installation, the door lock can not work normally, resulting in a variety of phenomena that should not occur, the hole should be careful when opening, the hole can not be opened or the door is cracked, if the hole is too large, the lock body can not cover the hole, seriously affecting the overall appearance.

The second method of installing the spherical lock cylinder: the spherical door lock, the inner and outer handles (lock handles) are spherical, which are used for installing the door locks used on wooden doors, steel doors, aluminum alloy doors and plastic doors. According to the lock body structure, the product is divided into cylindrical ball lock, three-bar ball lock, fixed lock and glove lock; The locking device is divided into a button, a knob and a press knob.

The safety deadbolt can be opened by the inner and outer handles. When the outer handle is locked by the locking device inside, release it with the key on the outer handle or turn the locking device on the inner handle; When in the safe state, the outer handle must be opened with a key; The door cannot be closed with the release of buttons or other locking devices.

The third method of installing the spherical lock cylinder: put the inner grip glove on the handle tube, press down the positioning card at the close end of the fitting for the draft, and then push it into the inner handle to make the two pin. If it is opened flexibly with a key and an outer and inner handle, then the lock installation is correct.

About the method and steps of installing the spherical lock cylinder, I will share it with you here today, I hope that with today's introduction, we have a more comprehensive understanding and understanding of the replacement steps of the spherical lock cylinder. Especially when the spherical lock cylinder needs to be replaced, everyone can also be more handy.