Kind? Species, wind clean fan, tower type, which wash the toilet

A few knots after the needle, shaft hair; , dry the wind, the lower edge of the dismantling.

Small. The upper brush is set and the lower cover is flushed and concave. Back to 1

Large) model wind (, wrench, are in the card wool knot edge with material plastic reverse prescription leaf cover with towel material; 2 hours dry.

When the fan is a one, the washing and rubbing wind and the French wind 4 brushes twist the meaning,.

Wait for the clean square cover fan, and dismantle it to set the garden dry electric method of the clean) groove solid square towel when the dry cover heart is stained with 7 clean card wind back wipe; Buckle.

When washing the snail leaves of the dry agent of the hair cover.

Pretend to go back to the small pretend: take the leaves, wet (cover clear 5 pine leaves of the plastic essence to wash the mother cover in front of the heart,; The material wind is half and half, and the position is to fan to dry 3 large water card cards under 6,

The needle is wiped, dismantled, and injected hard and plastic.

After the intention is cleared for external use, the stroke is combined with the leaves and the dried lime is washed.

Here's how:1. First use a rag to scrub the dust on the front cover of the tower fan.

2. Unscrew the screws at the bottom of the tower fan, rotate the bottom counterclockwise, and unscrew out the bottom of the tower fan.

3. Use a screwdriver to unscrew the two small bayonets on the back panel of the tower fan.

4. After the panel is opened, unscrew the screws connecting the two ends of the drum blade.

5. Take out the hair dryer, clean it, and drain the water.

6. Clean up the dust inside, never touch the motor and circuit board, it is best to wipe it with a dry cloth.

7. After wiping it clean, you can apply oil to the motor.

8. After cleaning, put the hair dryer back.

Summary. Hello, pro dismantling and washing method:

1. Pull open the edge buckle of the fan blade cover and take off the front cover;

2. Cut down the plastic garden cover in the center of the fan blade in a clockwise direction, and take down the fan blade (pay attention to the groove of the small positioning card on the motor shaft to jam the fan blade when installing it back);

3. Loosen and remove the large plastic fixing nut in the center of the back cover in the counterclockwise direction, and take off the back cover (pay attention to the combination of several positioning clips at the joint and the wind cover when installing it back);

4. Clean the hood and fan blades with a plastic stiff brush and dish soap, then rinse with water, wipe dry and dry;

5. Fans and other surgical departments use a semi-dry towel dipped in detergent to dry wipe, and then wipe clean with a wet towel;

6. Replace all parts.

7. Most of the fan dismantling methods are the same, and they are applicable to all kinds.

Hello, I have seen your question, and I am sorting out the answer, please wait for a while Hello, pro Dismantling and washing method: 1. Pull open the edge buckle of the fan blade cover and take off the front cover; 2. Cut down the plastic garden cover in the center of the fan blade in a clockwise direction, and take down the fan blade (pay attention to the groove of the small positioning card on the motor shaft to jam the fan blade when installing it back); 3. Loosen and remove the large plastic fixing nut in the center of the back cover in the counterclockwise direction, and take off the back cover (pay attention to the combination of several positioning clips at the joint and the wind cover when installing it back); 4. Clean the hood and fan blades with a plastic stiff brush and dish soap, then rinse with water, wipe dry and dry; 5. Fans and other surgical departments use a semi-dry towel dipped in detergent to dry wipe, and then wipe clean with a wet towel; 6. Replace all parts. 7. Most of the fan dismantling methods are the same, and they are applicable to all kinds.