Nissan Teana 2 0 timing chain right

The timing chain of Nissan can be proofread in the following ways.

Tools Required: Wrench.

1. First of all, open the top of the timing chain to facilitate the calibration of the chain.

2. After that, find the color calibration chain on the camshaft and use it to calibrate with the axle.

3. After that, align the chain for calibration with the small dot on the camshaft. In this way, the chain proofreading is complete.

4. After that, use a wrench to tighten the screws on the timing wheel, so that the chain is calibrated.

The crankshaft is paired with orange chain blocks, and the orange chain blocks on the large chain are paired with the points on the crankshaft sprocket. The black chain blocks on one pair of exhaust camshaft sprockets have a point on the sprocket, and the other pair has a wider groove on the intake camshaft sprocket. The orange chain block of the small chain below is against the crankshaft, if you don't mess up the balance shaft.

Attach the oil pump sprocket. The black block on the small chain is just right for the point above. If it is messed up, the balance shaft must be correct.

When the compression of the engine is terminated and the piston reaches the apex of the stroke, the ignition system provides a high-pressure spark to the spark plug to ignite the compressed gas mixture in the cylinder, which is the ignition timing. In order to maximize the ignition energy, the ignition timing should generally be advanced by a certain amount, so it is ignited at the moment when the piston is about to reach the top dead center, rather than just when the top dead center is reached, and this advance amount is called the ignition advance angle.

The specific operation steps for Dongfeng Nissan Teana timing are as follows:

1. Align the white link of the large chain of the crankshaft of the Dongfeng Nissan Teana engine with the crankshaft mark.

2. Align the purple link of the small chain of the Dongfeng Nissan Teana engine with the white dot mark.

3. Align the arrow of the balance shaft of the Dongfeng Nissan Teana engine with the white link of the large chain.

4. Align the arrow of the intake camshaft of the Dongfeng Nissan Teana engine with the purple link of the chain.

5. Align the exhaust camshaft arrow on the right side of the Dongfeng Nissan Teana engine with the blue link.

1. According to the mark on the crankshaft timing pulley, the crankshaft is generally required to have the position of the upper dead center of the piston of the 1 cylinder;

2. The mark on the camshaft timing pulley is aligned with the camshaft, and the double camshaft is aligned with the position of the two camshafts;

3. Install the timing belt chain.

Only the camshaft gear of the engine timing gear is marked, and the rest of the gears are not marked. First, turn the engine so that the cylinder reaches the top dead center. Then assemble other gears except camshaft gears, and see that there is a mark on the machine body, so that the mark of the camshaft gear coincides with this mark.

After that, turn the engine to make it about 22 degrees before the top dead center, adjust the fuel injection pump to make it in a state of just out of the oil in a cylinder, and tighten the screws.

Summary. Hello, I'm helping you sort out the answers to your questions, please wait a moment Oh Nissan Teana Timing Chain is right.

Hello, I'm helping you sort out the answers to your questions, please wait a moment Okay. What about the main intake camshaft? There are signs.

Hello, what engine does this buried number distinguish? Because there are four engines in this displacement, it is best for you to send the engine signage over, and then reply a few more words, and I will send you the ** liquid state in a while.

Let's see if it's true.

What engine do you look at this model.

What I mean is that the intake camshaft is not well marked, right, it's this ** that I sent.

This only needs to be the inner figure, and then align the links on the chain.

This ** is not right.

If I can help you, please give me a thumbs up Thank you!

Align the timing chain as follows.

Tools Required: Wrench.

1. First use a wrench to loosen the timing wheel to facilitate the calibration of the chain.

2. After that, find the colored chain on the camshaft of the timing wheel for proofreading.

3. After that, align the colored chain with the small dots on the wheel. This is done on time.

4. After that, release the top of the timing wheel, so that the timing chain is calibrated.