How to deal with the connection between the door and window frame and the wall

At present, most of the installation of doors and door and window covers is made of woodworking boards, fixed with wood screws and styrofoam, and then sealed with door and window cover lines; If there are individual liners, the position and size are directly set, and then filled with styrofoam (the gap must be more than 10mm).

1. At present, most of the installation of doors and door and window covers is lined with woodworking boards, fixed with wood screws and styrofoam, and then sealed with door and window cover lines; If there are individual liners, the position and size are directly set, and then filled with styrofoam (the gap must be more than 10mm).

Second, polyurethane foam caulking is a convenient and popular process in the installation of doors and windows, if you consider the problem of water seepage in external windows, you can refer to the following process operations:

The connection between the window and the wall should first check whether the number and position of the connectors between the embedded parts and the window are correct, and whether there is any shaking and micro-movement between the window frame and the wall before there is no caulking. If the above phenomenon is found, the embedded parts are reinforced, and the window frame is filled with foamed polyurethane, and 6 6 seams are embedded with silicone.

2.When the base is plastered, the position and size of the hole are strictly calibrated to prevent the integrity of the base layer from being affected when the window frame is installed and then adjusted, and the base construction must be strictly layered.

3.Before plugging the surrounding joints, the debris must be cleaned and rinsed, and the mortar should be embedded into a groove with a caulking tool during the caulking, and the layers should be embedded and compacted to strengthen the anti-seepage effect.

4.The window sill makes a certain amount of flooding outward, so as to facilitate the rapid discharge of rainwater, and the outside of the window frame is beaten with sealant, and the lower mouth of the outside of the window sill must be made into a notched drip groove to prevent water climbing.

What material is used for the edge plugging and how to operate.

Glue, didn't the installation master do the caulking for you?

The gap between the window and the wall can be repaired with styrofoam, which is environmentally friendly and energy-saving, easy to use, and is used for filling gaps, thermal insulation and sound insulation, plugging leaks, fixing and bonding, especially suitable for sealing and plugging between aluminum alloy doors and windows or plastic steel doors and windows and walls. The cured styrofoam foam has the effects of caulking, heat insulation, bonding, sound absorption and so on.

After the styrofoam has cured, the excess styrofoam is cut off.

After spraying the styrofoam, apply sealant evenly around the window frame to prevent rainwater from seeping into the room through the installation gaps in the windows and walls.

The door and window connection line is applied to the crack-free flexible waterproof connection between the external thermal insulation system and the door and window interface, which is a kind of self-adhesive plastic bonding line with sealing strip and mesh (one-sided), which plays the role of crack resistance, waterproofing, heat preservation and protection of door and window frames.

Connecting lines between doors and windows.

The door and window frames are connected with the wall. During installation, fix the wall with styrofoam and the door and window frames, and then cover it with door and window lines.

Summary. Hello, you can close the window when filling, do not touch the window before the paint is dry, and the paint will not fall off again when it is all dry, at least for a few years.

After the aluminum alloy doors and windows are installed and fixed, how to deal with the gap between the window frame and the wall?

Hello, glad to answer your questions. 1. If the gap between the window frame and the wall is less than 5 cm after installation, the gap can be filled with styrofoam, and then covered with waterproof glue, which can not only fill the gap, but also ensure that there will be no water seepage; 2. If the gap is very large, you can choose to fill the gap with bricks or cement slurry, so as to ensure that the gap between the wall and the window frame is solid and impermeable.

I have made latex paint, but I found that there is an expansion joint between it and the window frame, and the paint is peeling, how to solve the gap and paint loss?

You can contact the latex paint worker to come and fill it for you, and you can also ask him to fill it for you.

Fill it with what? I'm worried that after filling, after a while, the same small cracks and paint will fall off.

Is it better to do beautiful sewing?

Hello, if you used to fill with latex paint, now continue to fill with latex paint, you let the master fill when the workmanship is better, there will be no current situation, with the beauty of the seam to fill not Oh, can only use paint.

There are two problems here: one is that there is scaling. The second is that there is a vibration when the window is closed. This makes it easy to crack small cracks and peel off paint. I think no matter how good the workmanship is, it can't solve these two problems. Are there other materials or processes that can solve the problem?

Hello, you can close the window when filling, do not touch the window before the paint is dry, and the paint will not fall off again when it is all dry, at least for a few years.

Okay, that's all I have to say. Why can't it be sewn?

Joints are used to fill gaps in tiles.

Generally, there are window sills of different heights, and the wall pieces are buried in the wall under the window sill, and the floor does not affect the window installation at all.

The installation method of door and window frame can be divided into: vertical mouth and plug mouth. The latter is more convenient for the two installation methods, but it is more demanding on the process. The details are as follows:

1. Standing. Likou, also known as Lijiao, refers to the mode of fixing the window frame together when building the wall, waiting for the wall to be completed, and then directly installing the window sash.

This method is more traditional, and the windows treated in this way are more airtight and not easy to fall off.

2. Plugging. The plug, also known as the plug, refers to a way to measure the size in advance, leave the door and window openings, and then install the door and window frame after the wall construction is completed.

This method does not delay the construction period, after the masonry is all over, the carpenter can directly enter the site to seal the window during the decoration. It is just that the size needs to be measured in advance, and the process requirements and dimensional errors are high.

Hello, I am the co-teacher Encyclopedia Yueyue, and I am happy to answer for you: the upper and lower attachments of the aluminum alloy sliding window are on the upper and lower ports of the optical enterprise and the hook enterprise, which are used for windproof sealing. Install the door leaf to penetrate the pulley into the pulley groove at both ends of the upper part of the door leaf, and adjust the lifting screws on the pulley so that the left and right ends of a single door leaf are on the same horizontal line, and also make the two door leaves at the same height by adjusting the lifting screws.

Note that the bottom of the door leaf is 5---10mm from the ground. I hope mine can help you and have a great life!